Operating instructions

ManualsBrandsDraper ManualsHome building and DecorSLX14

Caution:

① Read instructions completely before proceeding.

② Test lift prior to installation.

③ Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

④ Do not obstruct operation of Scissor Lift SLX with ﬁ ngers or any object.

Serious injury or damage could result.

⑤ Maximum lifting capacity is 159 kg.

⑥ Scissor Lift SLX is designed to accommodate ceiling suspended

equip ment. Equipment should not be allowed to rest on optional ceiling

closure during operation (refer to section titled “Installing Pro jec tor”).

⑦ Entire bottom of unit must be unobstructed to permit proper op er a tion.

Sufﬁ cient clearance must be allowed below projector or op tion al ceiling

closure: 305cm for Model SLX10, 427cm for Model SLX14, etc.

⑧ Unit must be installed level (use a carpenter’s level).

⑨ Unit operates on 220V AC.

⑩ Verify the show position when testing lift. Make required changes by

referring to adjustment instructions on page 4 of this document.

CAUTION: Before servicing unit, disconnect hardwired control and any

remote control.

Note: Unit has been thoroughly inspected and tested at factory and found to be

operating properly prior to shipment.

Planning

① Based on screen location and projector speciﬁ cations, determine proper

position for projector in stal la tion.

② Conﬁ rm that there is adequate space for installation and operation.

Minimum clear ance above ceiling level varies according to Scissor Lift

model, plus height of projector, optional mounting bracket, optional ceiling

closure, and optional Environmental Air Space Housing.

③ Arrange to provide service access to the unit.

④ Maximum lifting capacity is 159 kg.

As Soon As Scissor Lift Arrives

① Open carton and inspect for damage.

② Locate the following parts:

A. The unit itself

B. Controls

C. Optional equipment: Environmental Air Space Housing, Universal

Projector Mount, closure panel or ceiling ﬁ nish kit (all ship in separate

cartons).

③ Test lift prior to installation.

Installation/Operating Instructions

220V SLX Scissor Lift Video Projector Lift by Draper

Hanging Unit

Please note: If using Environmental Air Space Housing option, go to

Environmental Air Space Housing instructions on page 3.

The Scissor Lift may be installed in a variety of ways; recessed above the

ceiling, or sus pend ed below the ceiling. The lift should be supported by four 12.7

thread ed mount ing rods. If ceiling recessed, the entire unit (including the projector)

should set approximately 38 mm above the ﬁ n ished ceiling in its “stored” position.

The threaded rods should pass through the corner mount ing ﬂ anges and be

secured by nuts above and below. The unit should then be guy wired or blocked to

pre vent swing ing.

All installations should observe the following guidelines:

① If installing above a hard ceiling, optional Draper Access Panels are

available to allow access to the unit.

② Installer must ensure that all fasteners and supports are of ad e quate

strength to securely support Scissor Lift and projector.

③ Fastening methods must be suitable for mounting surface, and se cure ly

Electrical Connections

Unit operates on 220V AC.

Opening the electrical box ex poses ter mi nals for ﬁ eld con nec tions. Unit is shipped

with internal wiring com plete.Wire to connect unit to power supply should be

furnished by in stall er. Con nec tions should be made in accordance with wiring

di a gram, and wiring should com ply with na tion al and local elec tri cal codes. All

op er at ing switches should be “off” before power is con nect ed.

Caution: Make sure electrical supply has been disconnected before

attempting to connect Scissor Lift to electricity.

Scissor Lift should be operated and checked prior to installing pro jec tor and/or

optional ceiling closure.

Low Voltage Control Switch shown below comes with 22.8 meters of cable and

should be plugged in to Control Panel on top frame of lift for control of the "Closed"

and "Show" positions. Momentary Key Switch shown below comes with 22.8

meters of cable and should be plugged in to Control Panel on top frame of lift for

control of the "Service" position.

If you encounter any difﬁ culties installing or servicing your Scissor Lift, call your dealer

or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.

anchored so that vibration or abusive pulling on unit will not weaken

installation.

④ Unit should be level, with weight shared more or less equally by all four

threaded mount ing rods.

⑤ Bottom of unit must be unobstructed after installation. Sufﬁ cient clear ance

must be allowed below projector or optional ceiling closure.

⑥ Do not use unit to support adjacent ceiling, light ﬁ xtures, etc.

⑦ Do not complete the ceiling below unit until electrical connections have

been completed and unit has been operated successfully.

⑧ We recommend that safety cables be attached to the Scissor Lift SLX for

added security (a sound in stal la tion practice with overhead equipment).

⑨ When the Scissor Lift SLX is to be installed in “other space used for

environmental air” the optional environmental air space housing must

be installed per instructions to isolate the lift from the “other space

used for environmental air.”

Operation

When unit is ﬁ rst operated, be cautious! If unit fails to operate when the

“down” button is pressed, press “off” and recheck elec tri cal con nec tions before

pro ceed ing. Cycle unit down and up several times to conﬁ rm sat is fac to ry

operation.

Caution: Do not pull on or touch safety belt when unit is in motion. If belt

locks, the cables will unspool.

Caution: Obstructing bottom pan may cause cables to unspool.

Standard Single Station Control (See Fig. 1) (CE Approved)—One three-button

switch with “up”, “down”, and “off” buttons. Lift starts up or down when ap pro pri ate

button is pressed, and may be stopped by pressing “off” button. Factory set

limit switch es stop lift automatically when pro jec tor is in “show” position. One

momentary key switch lowers lift from “show” to “service” position.

Optional Multiple Station Control (Not CE Approved)—Optional, moves lift from

“stored” to “show” position only. Each switch ing station has a three-button switch

with “up”, “down”, and “off” buttons. Lift starts up or down when ap pro pri ate button

is pressed, and may be stopped by pressing “off” button. Factory set limit switch es

stop lift automatically when pro jec tor is in “show” position.

Optional Key Operated Switch (Not CE Approved)—If ordered, the standard

LVC-S can be replaced with a second single station, momentary key-operated

three position (up/off/down) switch. Multiple Station Control re quired for this option.

Moves lift from “stored” to “show” position only.

Optional Infrared or Radio Frequency Remote Control (CE Approved)—If

ordered, a three-button transmitter is provided, with “up”, “down”, and “stop”

buttons. Unit starts up or down when appropriate button is pressed, and may be

stopped by pressing “off” button. Factory set limit switches stop unit au to mat i cal ly

when projector is in “show” po si tion. Only controls "show" and "stored" positions.

Optional RS232 Control (CE Approved)—For Serial communication an R2D7

Serial Communications Interface is optionally available.

Low Voltage Trigger (CE Approved)—Input provided for Low Voltage Trigger from

projector (see diagram on page 4).

Please Note: Scissor Lift SLX must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA

C22.1 and the National Electric Code (NEC), NFPA 70, as required. An appropriate

disconnect device shall be provided as part of the building installation.

OFF

DOWN

OFF

LVC-S SP-KSM

Closed & Show

Service

Figure 1

Caution: Beware

of pinch points

These Installation/Operating Instructions are available in the ofﬁ cial language

of the country where you purchase the product. Please contact your distributor to

request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises

dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez demander à

votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der ofﬁ ziellen

Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen

Sie die jeweilige Verkaufs-Abteilung.

Summary of content (7 pages)

PAGE 1
Installation/Operating Instructions 220V SLX Scissor Lift Video Projector Lift by Draper These Installation/Operating Instructions are available in the official language of the country where you purchase the product. Please contact your distributor to request a copy. Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur.
PAGE 2
20V Scissor Lift SLX by Draper page 2 of 7 Adjusting for Level or Center of Gravity Installing Projector Generally, the video projector should be suspended from the Projector Pan according to projector manufacturer’s instructions and recommended standard ceiling mounting hardware. The Scissor Lift SLX has a grounded 220V AC power cord for projector power supply. The power cord is laced down the back scissor and is “hot” at all times. Control cables should be laced through our Cable Management System.
PAGE 3
220V Scissor Lift SLX by Draper page 3 of 7 Installing Projector Using Universal Projector Mount ① ② ③ ④ ⑤ The universal projector mount includes: -2 x long arms -4 x short arms -4 x M3, 4 x M4, 4 x M5 and 4 x M6 mounting bolts (30mm in length) -4 spacers (½" [13 mm], 5/8" [16 mm], ¾" [19 mm], 7/8" [22 mm]) Determine which size mounting bolts suit your projector, and set others aside. They are no longer required.
PAGE 4
220V Scissor Lift SLX by Draper page 4 of 7 LVT RP/RQ WALL KEY Controls plug into the data cable inputs on the Control Panel, which is located on the Top Frame on the front side of the lift, using RJ14 connectors. RP/RQ Function Indicator Connecting Controls For IR or RF Remote Control, use data cable with RJ14 connectors on both ends. Pin 123456 YGRB For serial control of "Show" position, use data cable with RJ14 connectors on both ends and an R2D7 Serial Control Interface.
PAGE 5
www.draperinc.com (765) 987-7999 Wall Switch Key Switch BN Low voltage wiring by others RD WH RD BK Show Limit Switch RD Down Limit Switch BK Up Limit Switch Low Voltage Trigger (6 - 24 VDC) RP/RQ Bus Ports for remote controls such as Eye Port for IR Eye, RF Receiver, LED Wall Switch and RS232.
PAGE 6
220V Scissor Lift SLX by Draper page 6 of 7 Scissor Lift SLX Dimensions Table A 973.14 mm 919.16 mm Model SLX10 SLX14 SLX17 SLX21 SLX24 SLX28 SLX32 Closed Height 36cm 42cm 47cm 53cm 60cm 65cm 70cm 903.29mm 957.26mm See Table A 3.175 mm 889mm 920.75mm 1008mm 1066.8mm 41.275 mm 900.1mm 941.39mm 1066.8mm 1054.1mm 1031.9mm 527mm 127mm 1231.9mm571.5mm 482.6 mm www.draperinc.
PAGE 7
220V Scissor Lift SLX by Draper page 7 of 7 Installing Optional Environmental Air Space Housing The Environmental Air Space Housing is shipped in pieces, and must be assembled by the installer. The height of the Environmental Air Space Housing can be adjusted by moving the screws to different mounting holes in side panels. Aluminum tape is provided to cover unused holes. It is recommended that an access panel be installed in the ceiling to allow future access.