Operating instructions

ManualsBrandsDraper ManualsHome building and DecorSLX14

Planning

 Based on screen location and projector speciﬁcations, determine proper

position for projector installation.

 Conﬁrm that there is adequate space for installation and operation. Minimum

clearance above ceiling level varies according to Scissor Lift model, plus height

of projector, optional mounting bracket, optional ceiling closure, and optional

Environmental Air Space Housing.

 Arrange to provide service access to the unit.

 Maximum lifting capacity is 350 Lbs.

As Soon As Scissor Lift Arrives

 Open carton and inspect for damage.

 Locate the following parts:

A. The unit itself

B. Controls

C. Optional equipment: Environmental Air Space Housing, Universal

Projector Mount, closure panel or ceiling ﬁnish kit (all ship in separate

cartons).

 Test lift prior to installation. Please Note: Packaging must be removed from

lift before testing.

Installation/Operating Instructions

Scissor Lift SLX Video Projector Lift by Draper

Electrical Connections

Unit operates on 115V AC, 60 Hz. current. 10.93 amps current draw (3.93 amps

for lift, 7 amps for outlet). Opening the electrical box exposes terminals for ﬁeld

connections. Unit is shipped with internal wiring complete.Wire to connect unit

to power supply should be furnished by installer. Connections should be made

in accordance with wiring diagram, and wiring should comply with national and

local electrical codes. An appropriate disconnect device shall be provided as part

of the building installation. All operating switches should be “off” before power is

connected.

If you encounter any difﬁculties installing or servicing your Scissor Lift SLX, call your

dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

Operation

Before operating or testing the unit, make sure the

packaging has been removed from the unit. This can be

accomplished by removing the eight screws (four per side)

holding the packing frame to the lift. Once the packaging is

all removed, operate the lift in the "Up" direction, so the lift's

control encoder will recognize it's "home" location. Until you

do this, the Down function will not work.

When unit is ﬁrst operated, be cautious! If unit fails

to operate properly, press “off” and recheck electrical

connections before proceeding. Cycle unit down and

up several times to conﬁrm satisfactory operation. You

must also do this if the Scissor Lift ever loses or is

disconnected from the power.

Caution: Do not pull on or touch safety belt when unit

is in motion. If belt locks, the cables will unspool.

Caution: Obstructing bottom pan may cause cables

to unspool.

Standard Single Station Low Voltage Control (See Fig.

1)—One three-button switch with “Up”, “Down”, and “Off”

buttons. Lift starts up or down when appropriate button

is pressed, and may be stopped by pressing “Off” button.

Factory set limit switches stop lift automatically when

projector is in “show” position. One momentary key switch lowers lift from “Show”

to “Service” position.

Optional Multiple Station Control—Optional, moves lift from “Stored” to “Show”

position only. Each switching station has a three-button switch with “Up”, “Down”,

and “Off” buttons. Lift starts up or down when appropriate button is pressed,

and may be stopped by pressing “Off” button. Factory set limit switches stop lift

automatically when projector is in “Show” position.

Optional Key Operated Switch—If ordered, the standard LVC-S can be replaced

with a second single station, momentary key-operated three position (up/off/down)

switch. Multiple Station Control required for this option. Moves lift from “stored” to

“show” position only.

Optional Infrared or Radio Frequency Remote Control—If ordered, a three-

button transmitter is provided, with “up”, “down”, and “stop” buttons. Unit starts up

or down when appropriate button is pressed, and may be stopped by pressing

“off” button. Factory set limit switches stop unit automatically when projector is in

“show” position. Only controls "show" and "stored" positions.

Optional RS232 Control—For Serial communication an R2D7 Serial

Communications Interface is optionally available.

Low Voltage Trigger—Input provided for Low Voltage

Trigger from projector (see diagram on page 4).

Please Note: Scissor Lift SLX must be installed in accordance with the

requirements of the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70, as required. An

appropriate disconnect device shall be provided as part of the building installation.

Caution:

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions completely before proceeding.

DANGER: To reduce risk of shock:

 Always disconnect power from lift before cleaning.

WARNING–To reduce risk of burns, ﬁres, electric shock or injuries to persons:

 Disconnect power from lift before putting on or taking off parts.

 Use this lift only for its intended use as described in these instructions. Do

not use attachments not recommended by the manufacturer.

 Never operate this lift if it has a damaged cord or plug. If it is not working

properly, call your dealer or the manufacturer for assistance/repair.

 Keep cords away from heated surfaces.

 Never operate lift with air opening blocked. Keep the air openings free of lint,

hair, and the like.

 Never drop or insert any object into any opening.

 Do not use outdoors.

 Route cords and cables as shown in the instructions.

 WARNING: Rick of Electric Shock—connect this product to a

properly grounded electrical supply.

IMPORTANT INSTALLATION/OPERATING INSTRUCTIONS

WARNING: To prevent injury, this apparatus must be securely attached to

the building structure in accordance with the instructions.

 Test lift prior to installation. Please Note: Packaging must be removed from

lift before testing.

 Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

 Do not obstruct operation of Scissor Lift SLX with ﬁngers or any object.

Serious injury or damage could result.

 Lift is intended for use with product weighing not more than 350 pounds.

 Scissor Lift SLX is designed to accommodate ceiling suspended equipment.

Equipment should not be allowed to rest on optional ceiling closure

during operation (refer to section titled “Installing Projector”).

 Entire bottom of unit must be unobstructed to permit proper operation.

Sufﬁcient clearance must be allowed below projector or optional ceiling closure:

10' for Model SLX10, 14' for Model SLX14, etc

 Unit must be installed level (use a carpenter’s level).

 Unit operates on 115V AC 60 Hz. current. 10.93 amps current draw (3.93

amps for lift, 7 amps for outlet).

 Verify the show position when testing lift. Make required changes by referring

to adjustment instructions on page 4 of this document.

 The maintenance/service factory limit setting must not be adjusted to a lower

position than the preset factory limit setting. In addition, Draper does not

recommend setting show position at the maintenance/service position—for

example, if you wish to have 8' show position, order a lift with at least a 10'

maintenance position.

 When the Scissor Lift SLX is to be installed in “other space used for

environmental air” the optional environmental air space housing must

be installed per instructions to isolate the lift from the “other space

used for environmental air.”

 When Scissor Lift SLX is NOT installed in environmental air space housing

and optional ceiling closure, the ALTERNATE wiring for up limit switch may

be used (see Alternate Wiring schematic on page 5).

CAUTION: Before servicing unit, disconnect hardwired control and any

remote control.

Note: Unit has been thoroughly inspected and tested at factory and found to be

operating properly prior to shipment.

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK. DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

Scissor Lift SLX is approved to UL 2442 and CSA C22.2 No. 60065-03.

Caution:

Beware

of pinch

points

D C U

2¾"

4½"

/8"

Front Side Back

LVC-S

Up & Show

OFF

DOWN

OFF

SP-KSM

Service

Figure 1

Caution: Make sure electrical supply has been disconnected before

attempting to connect Scissor Lift to electricity.

Scissor Lift should be operated and checked prior to installing projector and/or

optional ceiling closure.

Low Voltage Control Switch shown below comes with 75' of non-plenum rated

cable and should be plugged in to Control Panel on top frame of lift for control

of the "Up" and "Show" positions. Momentary Key Switch shown below comes

with 75' of cable and should be plugged in to Control Panel on top frame of lift for

control of the "Service" position.

Summary of content (7 pages)

PAGE 1
Installation/Operating Instructions Scissor Lift SLX Video Projector Lift by Draper Caution: Important Safety Instructions Read all instructions completely before proceeding. DANGER: To reduce risk of shock: 1 Always disconnect power from lift before cleaning. WARNING–To reduce risk of burns, fires, electric shock or injuries to persons: 2 Disconnect power from lift before putting on or taking off parts. 3 Use this lift only for its intended use as described in these instructions.
PAGE 2
Scissor Lift SLX by Draper Hanging Unit Please note: If using Environmental Air Space Housing option, go to Environmental Air Space Housing instructions on page 7. The Scissor Lift may be installed in a variety of ways; recessed above the ceiling, or suspended below the ceiling. The lift should be supported by four ½" threaded mounting rods or bolts with locking nuts.
PAGE 3
Scissor Lift SLX by Draper page 3 of 7 Installing Projector Using Universal Projector Mount 1 2 3 4 5 The Universal Projector Mount includes: -2 x long arms -4 x short arms -4 x M3, 4 x M4, 4 x M5 and 4 x M6 mounting bolts (30 mm in length) -4 spacers (½" [13 mm], 5/8" [16 mm], ¾" [19 mm], 7/8" [22 mm]) Determine which size mounting bolts suit your projector, and set others aside. They are no longer required. If your projector has only three mounting holes, set aside one of the mounting arms (see Fig.
PAGE 4
Scissor Lift SLX by Draper page 4 of 7 Connecting Controls to Data Cable Splitter Board Controls plug into the Data Cable Splitter Board, which is located on the Top Frame on the front side of the lift, using RJ14 connectors. DETAIL OF DATA CABLE SPLITTER BOARD For IR or RF Remote Control, use data cable with RJ14 connectors on both ends. Any control, including automated dry contact systems, being connected to the wall switch input MUST send a momentary signal.
PAGE 5
Scissor Lift SLX by Draper page 5 of 7 Adjusting FULLY DOWN position Limit switches for the Scissor Lift SL are preset at the factory. The DOWN limit switch is set for the fully down (maintenance) position for the size lift you have ordered. The limit switch assembly is located inside the lift and behind the Lifting Cable Drum. DOWN The Down limit switche shown in the drawing are for setting the "Fully Down" position.
PAGE 6
Scissor Lift SLX by Draper page 6 of 7 Scissor Lift SLX Dimensions 9 /16" (14 mm) x4 Table A 385/16" (973 mm) 363/16" (919 mm) Closed Extended Model Height Height SLX10 141/16" 10'7" SLX14 165/16" 14'2" SLX17 189/16" 17'8" SLX21 2013/16" 21'3" SLX24 231/16" 24'9" SLX28 255/16" 28'5" 359/16" (903 mm) 3711/16" (957 mm) Top View See Table A /8" (3.175 mm) 1 35" (889 mm) 36¼" (921 mm) 391/16" (992 mm) 42" (1067 mm) 357/16" (900 mm) 371/16" (941 mm) 42" (1067 mm) 19/16" (39.
PAGE 7
Scissor Lift SLX by Draper page 7 of 7 Installing Optional Environmental Air Space Housing “other space used for environmental air.” Includes trim ring for ceiling opening. 1 Attach Environmental Air Space Housing top frame to top of Scissor Lift SLX with bolts provided. 2 Install top panel to Environmental Air Space Housing frame. 3 Attach assembly to overhead structure. Allow clearance between Environmental Air Space Housing top and structure for ease of future access.