Safety Instructions

ManualsBrandsDraperies.com ManualsElectronicsTubular motor

OPERATION GUIDE

Motor P1 button operation

Note: After the success of the reversing,retain all motor original settings.

Note:After the Reset to factor mode,will delete all previous system function setting and the emitter code.

2, Paring / Pair additional emitter / Remove one emitter

Enter paring status

Repeat paring operation

Loosen P1

Run for hint x1

4, Switch direction

5, Restore factory setting

Press 2s

Successful change the direction

Loosen P1

Run for hint x3

Press 10s

Restore factory setting successfull

Loosen P1

Run for hint x4

Press 14s

1, Short press function

Short press

Motor run upward / stoprunning / run downward ……

“Di~” x1

“Di” x3

“Di” x4

Note: This operation should be carried out under the conditions of motor has the limit.

Note: in the factory mode, enter paring status; In the user mode, enter pair additional emitter or remove one emitter.

Press 1s

The motor running

speed is improved

6 Speed Regulation

Press 1s

Run for hint x2

Press 1s

The motor running

speed is reduced

P2→Up/Down→Up/Down

Run for

hint x1

“Di” x1

Run for hint x1

“Di” x1

Press 1s

Run for hint x2

Press 1s

Run for hint x1

“Di” x1

Note: When the motor enters the radio lock mode, all the setting memory will be saved, only the radio receiving

function has been disabled.

3, Radio lock mode

The motor enters Radio Lock mode

Loosen P1

Run for hint x2

Press 6s

“Di” x2

Note: If the motor no response, it has already been the Max. or Min speed; The continuous motor speed has 3 grades,

20r/min, 24r/min, 28r/min, and the factory default is the fastest speed.

Fault and solution

ISSUE SOLUTION

The motor

doesn't run

NUMBER

a, Activate the motor afterfully charged

b, Paring again;

c, Contact after sales service

for more details

POSSIBLE CAUSES

a, The battery is not activated.

b, The emitter hasn't been paired;

c, If press P1 button for long time,

the motor no reaction, probably

the board is short circuit, or the

motor is broken.

Tubular Motor-

DM28LEU/S

Specification

(A-02)

P2→Stop→Stop

3rd limit

position

is ok

Press 1s Press 1s

Press 1s

2 3rd preferred stop position setting

2.1, Set the

3rd limit position

The 3rd limit position setting : If you have already set the upper and lower limit, then you can set the

3rd limit between upper and lower limit.

Run for hint x1

“Di” x1

Run for hint x1

“Di” x1

Run for hint x2

“Di” x3

Up+Down→Stop

Note: when under jog mode, press up/down button once, the motor will be jog running, if press more than 2S, the motor

will be continously running.

Press 5s Press 1s

Run for hint x1

1 Jog mode & running mode switch

Run for hint x2

“Di” x3

Run for hint x1

T<10s

Loosen P1

Paring is OK

Press 2s

Press 1s

Press 2s

Run for hint x1

The curtain

run downward

2 Switch rotating direction(optional)

Successfully switch direction

Upper

limit is OK

Press 2s

3.1, Setting the upper limit

3 Setting upper and lower limit

The curtain

run upward

Press 2s

3.2, Setting the lower limit

The curtain

run downward

The curtain

stops running

The curtain

stops running

User mode

Up→Stop→Up+Stop

Down→Stop→Stop+Down

Run for hint x2

“Di” x3

Press 2s

Lower

limit is OK

Run for hint x2

“Di” x3

Press 2s

Stop

1 Paring

Factory mode

Up→Up+Down

Note: In the user mode, power on the code can also operate;If 10s,no stay setting up emitter preess or no legal stop

button code,10s to the limit,will automatically exit the setting up mode.

If you need to reverse the rotateon of the motor controlled by the emitter,pls switch channel address.

Note: After the success of the reversing,retain all motor original settings.

Switch to jog mode

Switch to running mode

Run for

hint x1

“Di~” x1

Run for

hint x2

“Di” x3

“Di~” x1

The upper

limit

Run to the desired

upper position

Run to the desired

lower position

The lower

limit

Run to the req-

uired preferred

stop position

preferred stop

position

(Any position)

Run for

hint x1

T<10s

Loosen P1

Press 2s Press 2s

Loosen P1

Press 2s Press 2s

2.3, Clear the 3rd limit position

P2→Stop→Stop

2.2, Run to

the 3rd limit position

The motor runs automatically to

the 3rd limit position

Stop

Run for hint x1

“Di” x1

Run forhint x1

“Di~” x1

Clear

the 3rd limit position

is ok

Run for hint x1

“Di” x1

Run for hint x1

“Di” x1

Run for hint x2

“Di” x3

Run for hint x1

“Di” x1

Run for hint x1

“Di” x1

Run for hint x2

“Di” x3

Run for hint x2

“Di” x3

Run for hint x1

“Di” x1

Press 1sPress 1s

Press 2s

Press 1s

Press 1sPress 1sPress 1s

Press 2sPress 1sPress 1s

P2 P2

New emitter is paired to the motor

Run for hint x2

“Di” x3

Adjust the

required upper

limit position

Adjust the

required lower

limit position

The new

upper

limit is OK

Press 1s Press 2s

4 Pair additional emitter

3 Adjust limits

Method three

New emitter is paired to the motor

Method one

Run for hint x1

“Di” x1

Run for hint x2

“Di” x3

Run for hint x1

“Di” x1

Press 1sPress 1sPress 1s

Method one

P2 →P2 →P2

P2 P2

New emitter is paired to the motor

Method two

Method one

Method two

P2 →P2 →Stop

Up+Stop→Up/Down→Up+Stop

Down+Stop→Up/Down→Down+Stop

3.1, Adjusting the upper limit position

3.2, Adjusting the lower limit position

Press 5s

Run forhint x1

“Di~” x1

Run for hint x2

“Di” x3

Run forhint x1

“Di~” x1

Enter to

the process

of adjusting

the limit

The new

lower

limit is OK

Press 1s Press 2s

Press 5s

Enter to

the process

of adjusting

the limit

Stop

Note: After entering the limit fine-tuning mode, the original

3rd limit position

will not be deleted;If there is no

button operation in 2 minutes, 2 minutes time limit, motor chance to rotate the hint, and automatically exit the limit

fine-tuning mode;After fine-tuning the up/down limits can not be in the same position.

Run for hint x1 “Di~” x1

Run for hint x2

“Di” x3

Method two

Stop

Run for hint x1 “Di~” x1

P2 P2

One emitter have been removed

5 Remove one emitter

P2 →P2 →P2

One emitter have been removed

Note: Emitter is the paired emitter for master motor, is unpairing emitter; After the emitter is added, keep all

the original settings of the motor.

Note: are all of the code emitters,this method only can delete the emitter not the emitter ;After deleting

the emitter, keep all the settings of the motor (the limit is reserved for the previous setting).

Power on to 1Power off to 0

During the limit setting mode, press UP/DOWN once, the motor will jog running, if you press UP/DOWN 2S,

the motor will run continuously.

Successfully switch direction

Loosen P1

Run for hint x3

Press 10s

“Di” x3