Manual

ManualsBrandsDraw-Tite ManualsHardware63138 BIKE CARRIERS

ITEM: 63138

DESCRIPTION: Q-Slot 4 Bike Rack

Assembly Instructions:

1. Attach the (2) side tubes (short) to 2” shank assembly using the 5/16-18 x 2.25” carriage bolts and 5/16” lock nuts provided.

2. Attach the vertical center tube to 2” shank assembly using one 5/16-18 x 2.25” carriage bolt and 5/16” lock nut provided

Important Note: Tighten lock nuts so the support tubes still swing freely – see figure 2. There must be 1 – 2 threads of bolt

past end of lock nuts.

3. Rotate side tubes to the horizontal position as illustrated. Align holes in plates and side tubes and secure tubes in position

with bail pins as shown (Figure 1).

4. Rotate center tube to the vertical position as illustrated. Align holes in u-shaped bracket and tube and secure in position with

bail pin as shown.

DESCRIPTION QTY. DESCRIPTION QTY.

2” Shank Assembly 1 Support Tube Assembly 1

Side Tube - Short 2 1-1/4” Shank 1

Center Tube - Long 1 3/8-16 x 2.0 Carriage Bolt 2

5/16-18 x 2.25 Carriage Bolt 3 3/8-16 Hex Lock Nut 2

5/16-18 Hex Lock Nut 3 1/2-13 Anti-Rattle Pin 1

Bail Pin 3 1/2" Flat Washer 1

5/8-11 Anti-Rattle Pin 1 Wrench 3/4 , 1-1/16 1

5/8" Flat Washer 1 Spring Clip 2

LH Wheel Cradle Assembly 4 Frame Hook Assembly – Long 2

RH Wheel Cradle Assembly 4 Frame Hook Assembly – Short 2

Kit Contents:

TOOLS REQUIRED:

½” Wrench

9/16 Wrench

Cequent Performance Products, Inc.

Plymouth, MI 48170

Technical Service: (888) 521-0510

63138N Rev D 6-29-12

FIGURE 2.

Important:

1 – 2 Threads

Minimum

Side Tube (Short)

(2) Places

Center Tube (Long)

5/16” Carriage Bolt

(3) Places

Bail Pin

2” Shank Assembly

Pin Clip

5/8” Anti-Rattle Pin

5/16” Lock Nut

(3) Places

FIGURE 1.

5/8” Flat Washer

2” Hitch

Page 1 of 15

Printed in China

Label side up

Summary of content (15 pages)

PAGE 1
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack DESCRIPTION 2” Shank Assembly Side Tube - Short Center Tube - Long 5/16-18 x 2.25 Carriage Bolt 5/16-18 Hex Lock Nut Bail Pin 5/8-11 Anti-Rattle Pin 5/8" Flat Washer LH Wheel Cradle Assembly RH Wheel Cradle Assembly QTY. 1 2 1 3 3 3 1 1 4 4 Kit Contents: DESCRIPTION Support Tube Assembly 1-1/4” Shank 3/8-16 x 2.
PAGE 2
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Support Tube Assembly 1/2” Anti-Rattle Pin FIGURE 4 1/2” Flat Washer 3/8” Carriage Bolt 3/8” Nylon Lock Nut 1-1/4” Shank Pin Clip FIGURE 3 Assembly Instructions: 1. Attach the 1-1/4” Shank to Support Tube Assembly using (2) 3/8” carriage bolts and (2) 3/8” hex lock nuts (Figure 3). 2. Install Support Tube Assembly with 1-1/4” Shank the 2” Shank Assembly. Line up the threads in shank with hole in 2” shank and install the ½” anti-rattle pin.
PAGE 3
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Bicycle Loading: 1. Load inner bicycle first. Pull bail pins and rotate center tubes down as illustrated. (Fig 7) 2. Load bicycle into Wheel Cradles. Adjust cradles to appropriate position. Ensure tire is well supported at both ends of Wheel Cradles. Tighten cradles to prevent movement. (Fig 8) 3. Rotate center tube to vertical position and lock with bail pin. Lower Frame Hook assembly down over bicycle frame as illustrated. (Fig 9) 4.
PAGE 4
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Bicycle Loading (continued): 5. 6. 7. Loop Wheel Cradle straps over wheels and secure. (Fig 10) WARNING – Failure to use wheel cradle straps may result in bike falling off rack during use. Load second bicycle as describe in Bicycle Loading steps 2 thru 5. Reverse direction of second bicycle to prevent handle bar interference. (Fig 12) Bicycles with inclined frames (angled cross tube i.e.
PAGE 5
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack 5/8” Anti-Rattle Pin 1/2” Anti-Rattle Pin 5/8” Flat Washer 1/2” Flat Washer Clip Clip 1-1/4” Hitch 2” Hitch IMPORTANT NOTES: • This bicycle rack has been designed to carry a maximum of four (4) bikes in a 2” square hitch or up to two (2) bikes in a 1-1/4” receiver, see figures above. • When used as a four (4) bike carrier, DO NOT EXCEED maximum of 140 lbs (63 kgs). • When used as a two (2) bike carrier, DO NOT EXCEED maximum of 90 lbs (40 kgs).
PAGE 6
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack DESCRIPTION Bras d'accouplement 2 po Tube latéral - Court Tube central - Long Boulon de carrosserie 5/16-18 x 2.25” Contre-écrou hexagonal 5/16-18 Goupille en arceau Cheville antibruit 5/8-11 Rondelle plate 5/8” Berceau de roue gauche Berceau de roue droit Contenu de l'ensemble : DESCRIPTION QTÉ 1 Support tubulaire 2 Barre 1 1/4 po 1 Boulon de carrosserie 3/8-16 x 2.
PAGE 7
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Assemblage des supports tubulaires Cheville antibruit 1/2” FIGURE 4 Rondelle plate 1/2” Boulon de carrosserie 3/8” Contre-écrou nylon 3/8” Barre 1 1/4” Agrafe à ressort FIGURE 3 Instructions de montage : 1. Fixer la barre d'accouplement 1 1/4 po à l'assemblage de supports tubulaires à l'aide de deux (2) boulons de carrosserie 3/8 po et de deux (2) contre-écrous hexagonaux 3/8 po (Figure 3). 2.
PAGE 8
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Chargement des vélos : 1. Charger le vélo positionné vers l'intérieur en premier. Tirer les goupilles à arceau et faire pivoter les tubes centraux vers le bas, comme illustré. (Fig. 7) 2. Charger le vélo sur les berceaux de roue. Régler les berceaux à la position appropriée. S'assurer que le pneu est bien supporté aux deux extrémités des berceaux de roue. Serrer les berceaux pour prévenir tout mouvement. (Fig. 8) 3.
PAGE 9
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Chargement du vélo (suite) : 5. 6. 7. Bien attacher les sangles de berceau par-dessus les roues. (Fig. 10) AVERTISSEMENT - Non utilisation de sangles berceau de roue de vélo peut entraîner de tomber pendant l'utilisation en rack. Charger le deuxième vélo selon les instructions des étapes 2 à 5. Inverser l'orientation du deuxième vélo pour prévenir l'enchevêtrement des guidons. (Fig. 12) Dans le cas de vélos dont les cadres sont inclinés (p.ex.
PAGE 10
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Cheville antibruit 5/8” Cheville antibruit 1/2” Rondelle plate 5/8” Rondelle plate 1/2” Agrafe Attelage récepteur 2 po Agrafe Attelage récepteur 1 1/4 po NOTES IMPORTANTES : • Ce support à vélos a été conçu pour supporter un maximum de quatre (4) vélos dans un attelage récepteur carré de 2 po et jusqu'à deux (2) vélos dans un attelage récepteur de 1 1/4 po, voir les figures ci-dessus.
PAGE 11
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack DESCRIPCIÓN Ensamble del vástago de 2” Tubo lateral-corto Tubo central - largo Perno de carruaje, 5/16-18 X2.25 Tuerca de bloqueo hexagonal, 5/16-18 Pasador de asa Pasador anti-traqueteo, 5/8-11 Arandela plana, 5/8" Ensamble de la base de la rueda –izq. Ensamble de la base de la rueda – der. Contenido del kit: Cant. DESCRIPCIÓN 1 Ensamble del tubo de apoyo 2 Vástago, 1-1/4” 1 Perno de carruaje, 3/8-16 X2.
PAGE 12
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Ensamble del tubo de apoyo Pasador anti-traqueteo, 1/2" FIGURA 4 Arandela plana, 1/2" Perno de carruaje, 3/8" Tuerca de bloqueo de nylon, 3/8” Vástago, 1-1/4” Gancho pasador FIGURA 3 Instrucciones de ensamble: 1. Instale el vástago de 1-1/4” al ensamble del tubo de apoyo usando (2) pernos de carruaje de 3/8” y (2) tuercas hexagonales de bloqueo de 3/8” (Figura 3). 2.
PAGE 13
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Cómo cargar las bicicletas: 1. Cargue la bicicleta interior primero. Hale los pasadores de asa y rote los tubos centrales hacia abajo como se ilustra. (Fig 7) 2. Cargue la bicicleta en las bases de las ruedas. Ajuste las bases a la posición apropiada. Verifique que la llanta esté bien apoyada en ambos extremos de las bases de las ruedas. Apriete las bases para evitar el movimiento. (Fig 8) 3.
PAGE 14
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Cómo cargar las bicicletas (continuación): 5. 6. 7. Enlace las correas de la base de las ruedas sobre las ruedas y asegure. (Fig 10) ADVERTENCIA - No utilice correas de la rueda cuna puede resultar en bicicleta cayendo bastidor durante su uso. Cargue la segunda bicicleta como se describe en Cómo cargar las bicicletas, pasos 2 al 5 Reverse la dirección de la segunda bicicleta para evitar la interferencia de la barra del manubrio.
PAGE 15
ITEM: 63138 DESCRIPTION: Q-Slot 4 Bike Rack Pasador anti-traqueteo, 5/8" Arandela plana, 5/8" Pasador anti-traqueteo, 1/2" Arandela plana, 1/2" Gancho Gancho Enganche, 1-1/4” Enganche, 2” NOTAS IMPORTANTES: • Este portabicicletas está diseñado para transportar un máximo de cuatro (4) bicicletas en un enganche cuadrado de 2” o hasta dos (2) bicicletas en un receptor de 1-1/4”, ver las figuras arriba. • Cuando se usa como un cargador de (4) bicicletas, NO SUPERE el peso máximo de 140 lbs (63 kgs).