Owner manual

ManualsBrandsDraw-Tite ManualsCar63139 BIKE CARRIER - PRO SERIES DUETTE - TRUNK MOUNT

63139

Cequent Performance Products

Plymouth, MI 48170

63139N Rev B 11-13

Printed in China

Trunk Mount 2 Bike Carrier

Assembly Instructions:

1. Remove and inventory content from box. (Figure 1)

2. Rotate upper support tube and align adjustment hole with crescent slot in main support assembly.

3. Install the supplied 1/4” x 1-3/4” long carriage bolt , spacer, and adjustment knob as shown in Figure 2.

4. Slide bike arm assembly onto main assembly and fasten with fasteners as shown in figure 3. Tighten

1/4” Hex nut so bike arm is tight. Slide on rack end strap and install lock nut so 2 threads are show

beyond nut. This will allow the strap attachment to pivot freely.

5. Install attachment straps as shown in figure 4

Page 1 of 12

FIGURE 1

Lower Support

Kit Contents:

Main Bike Carrier 1 ¼-20 x 1-3/4 Hex Bolt 2

Bike Arm Support 2 Strap – Vehicle End 4

Instructions 1 Adjustment Knob 2

Spacer 2 ¼-20 x 1-3/4 Carriage Bolt 2

Strap – Carrier End 2 ¼-20 Hex Nut 2

¼-20 Lock Nut 2

ITEM

DESCRIPTION

1-7/8” Height Adjustment for Lower Support

Bike Retaining Strap

Adjustment Knob

Straps – Vehicle End

Strap – Carrier End

Spacer

Bike Arm Support

Upper Support

Strap – Vehicle End

Main Bike Carrier

Summary of content (12 pages)

PAGE 1
ITEM: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Kit Contents: Main Bike Carrier Bike Arm Support Instructions Spacer Strap – Carrier End 1 2 1 2 2 ¼-20 x 1-3/4 Hex Bolt Strap – Vehicle End Adjustment Knob ¼-20 x 1-3/4 Carriage Bolt ¼-20 Hex Nut ¼-20 Lock Nut 2 4 2 2 2 2 Assembly Instructions: 1. 2. 3. 4. 5. Remove and inventory content from box. (Figure 1) Rotate upper support tube and align adjustment hole with crescent slot in main support assembly.
PAGE 2
ITEM: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Shown Assembled Spacer 1/4-20 Lock Nut 1/4-20 Hex Nut (see note 4) 1/4-20 x 1-3/4 Long Hex Bolt Shown Assembled Adjustment knob 1/4 -20 x 1-3/4” long Carriage Bolt Strap – Carrier End FIGURE 2 FIGURE 3 Strap – Carrier End Strap – Vehicle End FIGURE 4 Mounting Rack to Vehicle: 1. 2. 3. 4. 5. 6. Hold the bike rack in approx. location on vehicle to see if the lower support needs to be put in the raised position (1-7/8” difference).
PAGE 3
ITEM: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Bicycle Loading: 1. 2. 3. 4. Load first bike so that the gears and de-railer are facing away from the vehicle. Load so that the top tube of the bicycle rest on the rack cradles. Route a cradle strap over top tube of bicycle then loop strap through heavy plastic loop. To secure strap place it back upon itself and pressing hook and loop together. Check to ensure bicycle is secure and unable to jump out of cradle. Figure 5.
PAGE 4
ITEM: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier IMPORTANT NOTES: • This bicycle rack has been designed to carry up to two (2)bikes, as long as the maximum weight on the rack does not exceed 34 kgs or 75 lbs. • Vehicles with a severely curved trunk or hatch along the top edge should not use this rack. Straps could slide to the side, causing your rack and bicycles to fall from the vehicle. • Always check tie down and hook and loop straps for tightness prior to each trip and often during a long trip.
PAGE 5
Article: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Contenu de l'ensemble : Principal porte-vélos Support de bras de vélo Instructions Espaceur Sangle - Transporteur extrémité Instructions de montage : 1. 2. 3. 4. 5. 1 2 1 2 2 Boulon ¼-20 x 1-3/4 Sangle - extrémité de véhicule Bouton de réglage Boulon de carrosserie ¼-20 x 1-3/4 Écrou hexagonal ½-20 Écrou de blocage ½-20 2 4 2 2 2 2 Retirer et vérifier le contenu de l'emballage.
PAGE 6
Article: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Montré assemblé Espaceur Écrou de blocage 1/4-20 Écrou hex. 1/4-20 (voir remarque 4) Boulon hex long 1/4-20 x 1-3/4 Montré assemblé Bouton de réglage Boulon de carrosseerie long 1/4-20 x 1-3/4 Sangle – Extrémité du porte-vélos FIGURE 3 FIGURE 2 Sangle - Transporteur extrémité Sangle - extrémité de véhicule FIGURE 4 Montage du porte-vélos sur le véhicule : 1. 2. 3. 4. 5.
PAGE 7
Article: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier Chargement des vélos : 1. 2. 3. 4. Charger le premier vélo de façon que les engrenages et le dérailleur soient du côté opposé au véhicule. Charger de façon que le tube supérieur du vélo repose dans les berceaux du porte-vélos. Faire passer une sangle de berceau dans les berceaux et par-dessus le tube supérieur du vélo. Faire passer la sangle dans la boucle en plastique robuste puis de retour sur elle-même.
PAGE 8
Article: 63139 DESCRIPTION : Trunk Mount 2 Bike Carrier REMARQUES IMPORTANTES : • Ce porte-vélos a été conçu pour transporter deux (2) vélos, à condition que le poids maximum qu'il supporte ne dépasse pas 34 kg (75 lb). • Les véhicules dont le coffre ou le hayon présente un bord supérieur très incurvé ne doivent pas recevoir ce porte-vélos. Les sangles risquent de glisser sur le côté, causant la chute du porte-vélos et des vélos du véhicule.
PAGE 9
ARTÍCULO: 63139 DESCRIPCIÓN : Trunk Mount 2 Bike Carrier Contenido del kit: Soporte para bicicletas principal Soporte del brazo de la bicicletas Instrucciones Espaciador Correa - portadora extremo 1 2 1 2 2 Perno hexagonal ¼ -20 x 1-3/4 Correa - vehículo extremo Perilla de ajuste Perno de carruaje ¼ -20 x 1-3/4 Tuerca hexagonal ¼ -20 Tuerca bloquee ¼ -20 Instrucciones de ensamble: 1. 2. 3. 4. 5. 2 4 2 2 2 2 Retire y realice el inventario del contenido de la caja.
PAGE 10
ARTÍCULO: 63139 DESCRIPCIÓN : Trunk Mount 2 Bike Carrier Se muestra instalado Espaciador Tuerca hexagonal, 1/4-20 (ver nota 4) Tuerca bloquee, 1/4-20 Perno hexagonal largo, 1/4-20 X 1-3/4” Se muestra instalado Perilla de ajuste Perno de carruaje, 1/4-20 X 1-3/4" de largo FIGURA 2 Correa - portadora extremo FIGURA 3 Correa - portadora extremo Correa - vehículo extremo FIGURA 4 Cómo instalar el cargador en el vehículo: 1. 2. 3. 4. 5. 6.
PAGE 11
ARTÍCULO: 63139 DESCRIPCIÓN : Trunk Mount 2 Bike Carrier Cómo cargar las bicicletas: 1. 2. 3. 4. Cargue la primera bicicleta de manera que los engranajes y los desviadores estén orientados en dirección contraria del vehículo. Cargue de manera que el tubo de la parte superior de la bicicleta se apoye en las bases del cargador. Pase una correa de la base a través de las bases y por encima del tubo superior de la bicicleta. Pase la correa por el ojal de plástico grueso y nuevamente sobre sí mismo.
PAGE 12
ARTÍCULO: 63139 DESCRIPCIÓN : Trunk Mount 2 Bike Carrier NOTAS IMPORTANTES: • Este cargador para bicicletas está diseñado para cargar hasta dos (2) bicicletas, siempre y cuando el peso máximo del cargador no supere los 34 kilos o 75 libras. • Los vehículos con un baúl bastante curvo o con puerta tipo escotilla a lo largo del borde superior no deben utilizar este cargador. Las correas podrían deslizarse hacia un lado y causar que el cargador y las bicicletas se caigan del vehículo.