Installation Manual

ManualsBrandsDraw-Tite ManualsAutomotiveDraw-Tite 75236 Max-Frame Class III 2" Square Receiver Hitch

Existing M12

Hex Washer Bolts

Both Sides

Frame

Bumper

Structure

Existing Weld Nuts

5 Places

Both Sides

Bumper Bracket

Both Sides

Figure 1

Hitch Shown In Proper Position

Frame Rail

Fascia

Installation Instructions

Toyota Tacoma

(Does Not Fit Toyota X-Runner)

Part Numbers:

33090

75236

87581

1. CAUTION: SUPPORT THE BUMPER STRUCTURE TO KEEP IT FROM SWINGING OUT OF POSITION DURING HITCH

INSTALLATION.

2. Referring to Figure 2, remove two (2) of the existing M12 hex washer bolts from the bumper bracket as shown, and loosen the

other three (3) bolts. Do this on both sides.

Rev. D07-18-0575236NSheet 1 of 2

z 2005 Cequent Towing Products

Hex Bolt, M12 x 40 x 1.25Qty. (4)

SpacerQty. (4)

Conical Washer, 1/2”Qty. (4)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Equipment Required: Torque Wrench

Wrenches: 10mm, 17mm, 19mm

Drill Bits: NONE

Fastener Kit: 75236F or F87581

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

5005000

Weight Carrying

Ball Mount

5505500

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Wiring Access Location: PU3, PU4

Remove

Loosen

Figure 2

Remove

Summary of content (6 pages)

PAGE 1
Part Numbers: Installation Instructions 75236 33090 87581 Toyota Tacoma (Does Not Fit Toyota X-Runner) Frame Rail Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or Fascia Max Gross Trailer WT (LB) Max Tongue WT (LB) Weight Distributing 5500 550 Weight Carrying Ball Mount 5000 500 Wiring Access Location: PU3, PU4 Hitch Shown In Proper Position Equipment Required: Torque Wrench Fastener Kit: 75236F or F87581 Hitch type Existing Weld Nuts 5 Places Both Sides Bumper Bracket Both
PAGE 2
Part Numbers: Installation Instructions 75236 33090 87581 Toyota Tacoma (Does Not Fit Toyota X-Runner) Existing M12 Hex Washer Bolts Both Sides Existing M12 Hex Washer Bolts Both Sides Figure 4 Figure 3 1 2 Qty. (4) Conical Washer, 1/2” 3 Qty. (4) Hex Bolt, M12 x 40 x 1.25 3. Raise the hitch into position so that the side brackets on the hitch are sandwiched between the bumper brackets and frame rails. Install the M12 x 1.25 x 40 bolts and washers and finger tighten. See Figure 3. 4.
PAGE 3
Numéros des pièces: Directives d’installation 75236 33090 87581 Toyota Tacoma (Ne convient pas au Toyota X-Runner) Rail du cadre Ne pas dépasser les limites inférieures du constructeur du véhicule, ou Plastique de carénage Attelage illustré dans la bonne position Équipement requis: Clé dynamométrique Trousse de visserie: 75236F ou F87581 Type de barre de remorquage Poids brut maximal de la remorque(LB) Poids maximal de la flèche d’attelage (LB) Répartition du poids 5500 550 Poids portant le mo
PAGE 4
Numéros des pièces: Directives d’installation 75236 33090 87581 Toyota Tacoma (Ne convient pas au Toyota X-Runner) Deux (2) boulons hexagonaux à rondelle existants M12 des deux côtés Boulons hexagonaux à rondelle existants M12 des deux côtés Figure 4 Figure 3 1 Qté. (4) 3 2 Qté. (4) 3. Élever la barre de remorquage en position de sorte que les attaches de côté sur la barre de remorquage soient prises en sandwich entre les attaches du pare-choc et les rails du cadre.
PAGE 5
Números de partes Instrucciones de instalación 75236 33090 87581 Toyota Tacoma (No se ajusta al Toyota X-Runner) Larguero del bastidor No supere el valor inferior entre la calificación del fabricante del vehículo del remolque o Placa protectora El enganche se muestra en la posición correcta Equipo necesario: Llave de torsión Kit de tornillos: 75236F o F87581 Tipo de enganche Peso bruto máximo del remolque (LB) Peso máximo en la horquilla (LB) Distribuidor de peso 5500 550 Carga de peso Montaje
PAGE 6
Números de partes: Instrucciones de instalación 75236 33090 87581 Toyota Tacoma (No se ajusta al Toyota X-Runner) Pernos hexagonales M12 con arandela existentes Ambos lados Pernos hexagonales M12 con arandela existentes Ambos lados Figura 4 Figura 3 1 2 Cant. (4) Arandela cónica, 1/2” Cant. (4) Perno hexagonal, M12 x 40 x 1.25 3 Cant. (4) Espaciador 3.