Owners manual

Hide-A-
Goose
Installation Instructions
Part Numbers:
9460/9470
9464/9474
Equipment Required:
Wrenches: 3/4” , 15/16”
Drill Bits:
3/16”, 9/16”, 3 1/2” Hole Saw,
*(5/8” - 4457 rail kit only)
30,000 LB (13,620 Kg) Max Gross Trailer Weight (GTW)
7500 LB (3405 Kg) Max Tongue Weight (TW)
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Fastener Kit: 58320 and 58312
Mounting Slots
*Inner mounting
slots
1
11
1
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
8
88
8
9
99
9
11
Locking Pin
Figure 1
Figure 2
Alignment Pin
Ball Sleeve
See Note on
Page 2
12
Magnetic
Cover
*Note! 4457 Rail Kit Only
Fasteners for (2) additional
attachments are supplied
with 4457 rail kit. See
Figures 1,2 & 4 and also
lines 5A & 5B on next page.
*4457 rail kit only
IMPORTANT!
This product is intended to be used with Cequent Performance Products manufactured mounting kits. If the Gooseneck hitch installation is made
with Cequent manufactured mounting kits, the installation instructions for the Gooseneck hitch are included as part of the mounting kit installation
instructions. Give this installation instruction to vehicle owner after installation is complete.
General instructions for fabricated support structures.
IF CEQUENT PERFORMANCE PRODUCTS MANUFACTURED MOUNTING KITS ARE NOT USED, THIS PRODUCT BECOMES A
GENERAL APPLICATION PRODUCT. IT IS THE RESPONSIBILITY OF THE INSTALLER TO SELECT STRUCTURALLY SAFE
MATERIALS AND LOCATIONS FOR ATTACHMENT. INSTALLATION INFORMATION FOLLOWS.
© 2012 Cequent Performance Products Sheet 1 of 2 9460N 5-3-12 Rev. G
1
11
1
Qty. (1) Head
7
77
7
Qty. (2) 1/2” U-Bolts
2
22
2
Qty. (4) *(6) 5/8” -11 X 2.00 Grade 8 Carriage Bolt
8
88
8
Qty. (4) 1/2 Flat Washer
3
33
3
Qty. (4) *(6) Conical Toothed Washer
9
99
9
Qty. (4) U-Bolt Spring
4
44
4
Qty. (4) *(6) 5/8”-11 Hex Nut



Qty. (4) 1/2”-13 Lock Nut
5
55
5
Qty. (1) Handle Qty. (1) 2-5/16” Ball
6
66
6
Qty. (1) Spring Clip Qty. (1) Vinyl Handle
Tighten all 5/8 grade 8 fasteners with torque wrench to 210 Lb.-Ft. (285 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
9
99
9



11
Locking Pin
Holding Slots
Figure 2
Figure 3
Locking Pin
12
Tighten all 5/8 grade 5 fasteners with torque wrench to 150 Lb.-Ft. (203 N*M)
Printed in China
A brand label, either Draw-Tite or BullDog, is supplied with this
hitch. After installing mounting kit to truck frame peel and apply
this label to surface of frame bracket.