i
Vigor Router 11ax Series Quick Start Guide Version: 1.0 Firmware Version: V4.4.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2135ax, Vigor2765ax, Vigor2766ax series router is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.draytek.com.tw/ftp/Vigor2765ax/Document/CE/ https://www.draytek.com.tw/ftp/Vigor2766ax/Document/CE/ https://www.draytek.com.tw/ftp/Vigor2135ax/Document/CE/ Manufacturer: DrayTek Corp. Address: No. 26, Fushing Rd.
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents 1. Package Content .................................................................................................. 1 2. Panel Explanation................................................................................................. 2 2.1 Broadband Router - Vigor2135ax, Vigor2135Vax ...................................................................... 2 2.2 35b Security Router - Vigor2765ax, Vigor2765Vax.................................................................... 4 2.3 G.
1. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Router Quick Start Guide RJ-45 Cable (Ethernet) RJ-11 to RJ-11 Cable (Annex A) RJ45 to RJ45 Cable (Annex B) RJ11 to RJ45 Cable (Annex B) The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 27.6 Watt.
2. Panel Explanation 2.1 Broadband Router - Vigor2135ax, Vigor2135Vax Vigor2135ax LED ACT WAN WLAN USB (for “V” model) Status Off Blinking Blinking with WLAN On Blinking Off Off On Blinking Blinking with WLAN Vigor2135Vax Explanation The system is not ready or is failed. The system is ready and can work normally. WPS is enabled and waiting for the response from the wireless client. Internet connection is ready. The data is transmitting. Internet connection is not ready.
Interface WLAN ON/OFF WPS Description Wireless band will be switched /changed according to the button pressed and released. For example, 2.4G (On) and 5G (On) – in default. 2.4G (Off) and 5G (On) – pressed and released the button once. 2.4G (On) and 5G (Off) – pressed and released the button twice. 2.4G (Off) and 5G (Off) – pressed and released the button three times. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds.
2.2 35b Security Router - Vigor2765ax, Vigor2765Vax Vigor2765ax LED ACT Status Explanation Off Blinking Blinking with WLAN On The system is not ready or is failed. The system is ready and can work normally. WPS is enabled and waiting for the response from the wireless client. The DSL link up, waiting for the Internet connection. Slowly - The DSL connection is ready for training. Quickly - The DSL connection is synchronizing. The router is ready to access to the Internet through DSL link.
Interface WLAN ON/OFF WPS Description Wireless band will be switched /changed according to the button pressed and released. For example, 2.4G (On) and 5G (On) – in default. 2.4G (Off) and 5G (On) – pressed and released the button once. 2.4G (On) and 5G (Off) – pressed and released the button twice. 2.4G (Off) and 5G (Off) – pressed and released the button three times. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds.
2.3 G.Fast Security Router - Vigor2766ax, Vigor2766Vax Vigor2766ax LED ACT Status Explanation Off Blinking Blinking with WLAN On The system is not ready or is failed. The system is ready and can work normally. WPS is enabled and waiting for the response from the wireless client. The DSL link up, waiting for the Internet connection. Slowly - The DSL connection is ready for training. Quickly - The DSL connection is synchronizing. The router is ready to access to the Internet through DSL link.
Interface WLAN ON/OFF WPS Description Wireless band will be switched /changed according to the button pressed and released. For example, 2.4G (On) and 5G (On) – in default. 2.4G (Off) and 5G (On) – pressed and released the button once. 2.4G (On) and 5G (Off) – pressed and released the button twice. 2.4G (Off) and 5G (Off) – pressed and released the button three times. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds.
3. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. 3.1 Network Connection 1. Connect the DSL interface to the land line jack with a DSL line cable. 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. 3.
3.2 Wall-Mounted Installation Vigor router has keyhole type mounting slots on the underside. 1. Drill two holes on the wall. The distance between the holes shall be 100.75mm. The recommended drill diameter shall be 6.5mm (1/4”). 2. Fit screws into the wall using the appropriate type of screw plug. 3. Hang the Vigor router directly onto the screws. (Here we take Vigor2765ax as an example.
4. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. Make sure your PC connects to the router correctly.
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.
On the next page as shown below, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if 3G USB modem is used, please choose WAN3. Then click Next for next step. WAN1, WAN2 and WAN3 will bring up different configuration page. Here, we take WAN1 (ADSL/VDSL2) as an example. On the next page as shown below, please select the appropriate protocol according to the information from your ISP.
2. After finished the above settings, simply click Next. 3. Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
MPoA / Static or Dynamic IP 1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page. 2. Please enter the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. 3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 4. Now, you can enjoy surfing on the Internet.
5. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”. Be a Registered Owner Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
