Vigor2866 Series G.Fast Security Firewall Quick Start Guide (for RF Model) Version: 1.2 Firmware Version: V4.0.5.
Date: April 28, 2020 ii
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2865 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2865/Document/CE/ Manufacturer: DrayTek Corp. Address: No.26 Fu Shing Rd., Hukou County, Hsin-Chu Industrial Park, Hsin-Chu City, Taiwan 303 Product: Vigor2865 Series Frequency Information for Europe area: 2.
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents 1. Package Content.....................................................................................................1 2. Panel Explanation...................................................................................................2 2.1 Vigor2865FVac/Vigor2866FVac .................................................................................................... 2 2.2 Vigor2865ac/Vigor2866ac..........................................................................................
1. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Besides, the content is subject to the real package. or Vigor router Antenna RJ-45 to RJ-45 Cable (Annex B) RJ-11 to RJ-45 Cable (Annex B) RJ-11 to RJ-11 Cable (Annex A) Quick Start Guide The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 28 Watts.
2. Panel Explanation 2.1 Vigor2865FVac/Vigor2866FVac LED ACT Status Off Blinking WAN2 On Off Blinking On Off On Off Blinking On QoS USB DSL Blinking Phone1/2 On Off Blinking 2.4G/5G On Off Blinking LED on Connector Left On WAN2 LED Off / P6 Blinking Right On Explanation The router is powered off. The router is powered on and running normally. Internet connection is ready. Internet connection is not ready. The data is transmitting. The QoS function is active. The QoS function is inactive.
LAN P1~P5 LED Left LED Right LED Off On Off Blinking On Off The port is connected with 10/100Mbps. The port is connected. The port is disconnected. The data is transmitting. The port is connected with 1000Mbps. The port is connected with 10/100Mbps The port “WAN2 / P6” is switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI.
DSL Connecter for accessing the Internet. Connecter for installing WLAN antennas. PWR Connecter for a power adapter. ON/OFF Power Switch.
2.2 Vigor2865ac/Vigor2866ac LED ACT Status Off Blinking WAN2 On Off Blinking On Off On Off Blinking On QoS USB DSL Blinking WCF On Off 2.4G/5G On Off Blinking DMZ On Off Blinking LED on Connector Left On WAN2 LED Off / P6 Blinking Explanation The router is powered off. The router is powered on and running normally. Internet connection is ready. Internet connection is not ready. The data is transmitting. The QoS function is active. The QoS function is inactive.
LAN P1~P5 Right LED Left LED Right LED On Off On Off Blinking On Off The port is connected with The port is connected with The port is connected. The port is disconnected. The data is transmitting. The port is connected with The port is connected with 1000Mbps. 10/100Mbps. 1000Mbps. 10/100Mbps The port “WAN2 / P6” is switchable. It can be used for LAN connection or WAN connection according to the settings configured in WUI.
DSL Connecter for accessing the Internet. Connecter for installing WLAN antennas. PWR Connecter for a power adapter. ON/OFF Power Switch.
3. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. (For the hardware connection, we take “ac” model as an example.) 3.1 Network Connection 1.
3.2 Wall-Mounted Installation Vigor router has keyhole type mounting slots on the underside. 1. Drill two holes on the wall. The distance between the holes shall be 168mm. 2. Fit screws into the wall using the appropriate type of wall plug. Note 3. The recommended drill diameter shall be 6.5mm (1/4”). When you finished about procedure, the router has been mounted on the wall firmly.
4. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. 4.1 Quick Start Wizard for Network Connection The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. Make sure your PC connects to the router correctly.
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. Here we take Vigor2865ac as an example. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next.
On the next page as shown below, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if wireless 2.4G/5G connection is used, please choose WAN3 or WAN4; if 3G USB modem is used, please choose WAN5 or WAN6. Then click Next for next step. Each WAN interface will bring up specific configuration page. Here, we take WAN1 (ADSL/VDSL2) as an example. Click Next to go to the following page.
PPPoE/PPPoA 1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page. 2. After finished the above settings, simply click Next.
3. Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection. 4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 5. Now, you can enjoy surfing on the Internet.
MPoA / Static or Dynamic IP 1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page. 2. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. 3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 4. Now, you can enjoy surfing on the Internet.
5. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
