VIGOR 2820VS Snelstart Handleiding
Inhoudsopgave INHOUDSOPGAVE......................................................................................................................... 2 VERPAKKINGSINHOUD / VOORBEREIDING..................................................................................... 3 LED INDICATIE / AANSLUITINGEN .................................................................................................. 4 VERBINDEN VAN DE ROUTER EN HET COMPUTERSYSTEEM ............................................................
Verpakkingsinhoud / Voorbereiding Voor meer gedetailleerde instructies over het configureren van de Vigor 2820VS, kijk op www.draytek.nl Verpakkingsinhoud DrayTek Vigor 2820VS router. CD-ROM met Engelstalige handleiding, firmware en hulpprogramma’s. Ethernet CAT-5 UTP kabel. Voedingsadapter. Nederlandstalige snelstart. Engelstalige snelstart. Bevestigingsmateriaal voor wandmontage. 2 ISDN splitter kabels voor het aansluiten van meerdere toestellen op 1 ISDN poort.
LED indicatie / aansluitingen Led indicatie LED Soort ACT Activiteit USB CSM WCF DSL Link Link Link Link WAN2 Line Phone QoS Link Link Link Omschrijving Knippert langzaam wanneer er spanning op de router staat en de router normaal functioneert. Knippert snel(ler) wanneer de router in firmware mode staat. Brand wanneer er een USB 3G modem of een printer is aangesloten. Brand wanneer IM en P2P filter is ingeschakeld. Indicatie led voor ingeschakelde Web Content Filter.
Verbinden van de router en het computersysteem - - Zet uw computersysteem uit. Sluit uw computersysteem aan op één van de LAN aansluitingen. Sluit de internet verbinding aan op de DSL poort of op de WAN2 poort, afhankelijk van het type internet verbinding. Sluit de voedingsadapter aan. Zet de Vigor 2820VS router aan. Zet uw computersysteem aan. De ACT LED gaat knipperen indien de router correct werkt.
Configureer uw Computer in Windows Vista 1. Ga naar Start / Configuratiescherm (in klassieke weergave). In het configuratiescherm, dubbel- klik op Netwerkcentrum 2. Kies in het menu aan de linkerkant voor Netwerkverbindingen beheren. 3. Klik één keer op de aangesloten netwerkadapter met de rechtermuisknop en selecteer Eigenschappen. 4. Selecteer Internet Protocol versie 4 (TCP/IPv4) en klik op Eigenschappen. 5.
Configureer uw Computer in Windows XP 1. Ga naar Start / Instellingen / Configuratiescherm (in klassieke weergave). In het configuratiescherm, dubbel- klik op Netwerk verbindingen. 2. Dubbel-klik op LAN-verbinding. 3. In het Status van LAN verbinding scherm, klik op Eigenschappen. 4. Selecteer Internet Protocol (TCP/IP) en klik op Eigenschappen. 5. Selecteer Automatisch een IP-adres laten toewijzen en Automatisch een DNS serveradres laten toewijzen. 6. Klik OK om de configuratie te beëindigen. 7.
Configureer uw Computer in Windows 2000 1. Ga naar Start / Instellingen / Configuratiescherm. In het configuratiescherm, dubbelklik op Netwerk en inbelverbindingen. 2. Dubbel klik op LAN verbinding. 3. In het Status van LAN verbinding scherm, klik op Eigenschappen. 4. Selecteer Internet Protocol (TCP/IP) en klik op Eigenschappen. 5. Selecteer Automatisch IP-adres verkrijgen en Automatisch een DNS serveradres laten toewijzen. 6. Klik OK om de configuratie te beëindigen. 7. Sluit nu alle vensters met OK.
Configureer uw Computer in Windows 98 / ME 1. Ga naar Start / Instellingen / Configuratiescherm. In het configuratiescherm, dubbelklik op Netwerk en selecteer het Configuratie tabblad 2. Selecteer TCP/IP ->(van uw netwerk adapter) klik vervolgens op Eigenschappen. 3. Selecteer Automatisch een IP-adres laten toewijzen. 4. Ga vervolgens naar het tabblad DNS Configuratie. 5. Selecteer DNS uitschakelen en klik op OK om de configuratie te beëindigen. 6. Sluit nu alle vensters met OK.
Configureer uw Computer in Windows NT 1. Ga naar Start / Instellingen / Configuratiescherm. In het configuratiescherm, dubbelklik op Netwerk en selecteer het tabblad Protocol. 2. Selecteer TCP/IP protocol en klik op Eigenschappen. 3. Selecteer Automatisch IP-adres verkrijgen van een DHCP server en klik op OK. 4. Sluit nu alle vensters met OK. Ga nu naar Pagina 12 om verder te gaan met de configuratie.
Configuratie onder MacOS / MacOS X Mac OS (8.x / 9.x) Klik op Apple (icoon) > Regelpanelen > TCP/IP. Onder Verbind via selecteert u Ethernet. Onder Configureer selecteert u Via DHCP-server. Sluit links bovenin het TCP/IP scherm. Klik op Bewaren indien daarom gevraagd wordt. Herstart de Apple Macintosh. Apple MacOS X Klik op Apple (icoon) > Systeemvoorkeuren > Netwerk. Selecteer bij Toon: de optie Ingebouwd Ethernet. Selecteer onder de tab TCP/IP de optie Via DHCP. Klik op Pas nu toe.
Benaderen van de Webconfiguratie Om de Vigor 2820VS te configureren dient u te beschikken over Microsoft Internet Explorer 5.0 / Netscape 4.5 of hoger. 1. Open uw internet browser. Typ in de adresbalk http://192.168.1.1 Dit nummer is het standaard IPadres voor deze router. Druk vervolgens op Enter. 2. Een gebruikersnaam en wachtwoord scherm zal nu verschijnen. Klik op OK om door te gaan. Standaard heeft de router geen gebruikersnaam en wachtwoord.
Configuratie WAN1 DSL Instellingen voor ADSL via KPN Telecom De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN1: - Enable Yes - Display Name ADSL - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor ADSL via BBned De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN1: - Enable Yes - Display Name ADSL - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen. Kies in het hoofdmenu voor: WAN >> Internet Access Klik op WAN 1 om de configuratie voor ADSL te maken.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor ADSL via Tiscali / BabyXL De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN1: - Enable Yes - Display Name ADSL - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen. Kies in het hoofdmenu voor: WAN >> Internet Access Klik op WAN 1 om de configuratie voor ADSL te maken.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor ADSL via Versatel De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN1: - Enable Yes - Display Name ADSL - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen. Kies in het hoofdmenu voor: WAN >> Internet Access Klik op WAN 1 om de configuratie voor ADSL te maken.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Configuratie WAN2 Ethernet Instellingen voor ADSL via KPN Telecom i.c.m een Speedtouch Home De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN2: - Enable Yes - Display Name breedband - Physical Type Auto negotiation - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor ADSL via KPN Telecom i.c.m. Speedtouch 500/700 serie De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN2: - Enable Yes - Display Name breedband - Physical Type Auto negotiation - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor internet via ZIGGO De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN2: - Enable Yes - Display Name breedband - Physical Type Auto negotiation - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. U bent nu klaar met de configuratie van de internet verbinding.
Instellingen voor internet via Breedband Dynamisch De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN2: - Enable Yes - Display Name breedband - Physical Type Auto negotiation - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. De verbinding controleren Kies in het hoofdmenu voor: Online Status De huidige status van de router verschijnt.
Instellingen voor internet via PPPoE De Internet verbinding configureren Kies in het hoofdmenu voor: WAN >> General Setup. De algemene instellingen voor de internet verbinding worden in het scherm aangemaakt. Vul de volgende gegevens in bij WAN2: - Enable Yes - Display Name breedband - Physical Type Auto negotiation - Load Balance Mode Auto Weight - Active mode Always On Druk op OK om de instellingen toe te passen.
Als uw instellingen correct zijn ingevoerd zal het scherm hiernaast verschijnen. Klik na ongeveer 10 seconden op de Hyperlink 1st http://192.168.1.1:80 Nu zal het hoofdmenu van de router weer verschijnen en zal de internetverbinding na ongeveer 1 minuut actief zijn. De verbinding kunt u controleren door de onderstaande stappen te volgen. De verbinding controleren Kies in het hoofdmenu voor: Online Status De huidige status van de router verschijnt.
FAQ 1. Wat is de inlog naam en het inlog wachtwoord voor toegang tot de router? De standaard inlog naam is admin. Standaard is er geen inlog wachtwoord ingesteld. U kunt in de Router Web Configurator onder System Maintenance > Administrator Password bij New Password en Retype New Password een wachtwoord invoeren zodat uw Vigor 2820VS beveiligd is. 2. Ik ben het inlog wachtwoord vergeten.
De kleine lettertjes Voorbehoud We behouden ons het recht voor om deze en andere documentatie te wijzigen zonder de verplichting gebruikers hiervan op de hoogte te stellen. Afbeeldingen en screenshots kunnen afwijken. Garantie Wij garanderen dat de DrayTek Vigor routers gedurende de eerste drie jaar na aankoop, vrij zullen blijven van defecten als het gevolg van fabricagefouten en defecte onderdelen.