Vigor2130 Quick Start Guide i
Vigor2130 Series High Speed Gigabit Router Quick Start Guide Version: 1.
Copyright Information Copyright Declarations Copyright 2009 All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: z Microsoft is a registered trademark of Microsoft Corp.
European Community Declarations Manufacturer: Address: Product: DrayTek Corp. No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Vigor2130 Series Router DrayTek Corp. declares that Vigor2130 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
Table of Contents 1. Introduction........................................................................................................... 1 1.1 Panel Explanation ...................................................................................................................... 2 1.1.1 For Vigor2130 ............................................................................................................... 2 1.1.2 For Vigor2130n .......................................................................
1. Introduction The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be greater than 900 Mbps almost. With the development of NGN (Next Generation Network), you may recently hear the news about FTTx deployment in your local area or even have already subscribed the unbundling last mile service (e.g. VDSL2) from local ITSP for FTTx.
1.1 Panel Explanation 1.1.1 For Vigor2130 LED Status Explanation ACT (Activity) Blinking Off On Off The router is powered on and running normally. The router is powered off. Hardware NAT is enabled. Hardware NAT is disabled. USB1/2 VPN QoS DoS On Blinking On Off Blinking On On On The WAN port is connected. It will blink while transmitting data. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active. The VPN tunnel is active.
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power switch.
1.1.2 For Vigor2130n LED Status Explanation ACT (Activity) Blinking Off On Off The router is powered on and running normally. The router is powered off. Hardware NAT is enabled. Hardware NAT is disabled. On Blinking On Off Blinking On On On The WAN port is connected. It will blink while transmitting data. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active. The VPN tunnel is active. The QoS function is active.
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power switch.
1.1.3 For Vigor2130Vn LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. Hardware NAT is enabled. Hardware NAT is disabled. Off On Off HPA (Hardware Packet Accelerate) WAN LAN1/2/3/4 USB1/2 Phone1/ Phone2 On Blinking On Off Blinking On Blinking On Off The WAN port is connected. It will blink while transmitting data. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active.
Interface Description Phone2/Phone1 Connector of analog phone for VoIP communication. Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power switch.
1.2 Package Content n Quick Start Guide o CD p RJ-45 Cable (Ethernet) q Antenna (n models) r Stand s The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.
2. Installing Your Router This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. 2.1 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. 1. Connect this device to a modem with a RJ-45 cable. 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. 3.
Stand Installation The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation.
2.2 Printer Installation You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients). 1. Connect the printer with the router through USB port. 2. Open Start->Settings-> Printer and Faxes.
3. Open File->Add a New Computer. A welcome dialog will appear. Please click Next. 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next.
6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish.
9. Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next. 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new printer you have added. 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and UPR name.
The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional functions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.
This page is left blank.
3. Configuring Web Pages To access Internet, please finish basic configuration after completing the hardware installation. 3.1 Accessing Web Page 1. Make sure your PC connects to the router correctly. Notice: You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to the later section - Trouble Shooting of the guide. 2.
3.2 Basic Configuration The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Open a web browser on your PC and type http://192.168.1.1. The system will ask you to type username/password. The displayed web pages will change according to the username and password typed. Here we take simple web pages for example. So, do not type any word on the window and click Login.
4. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue. After restarting the router, new password must be typed for accessing into router web page. 5. On the next page as shown below, please choose time zone for your router. Set/add NTP server(s). Then click Next for next step.
6. On the next page as shown below, please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step.
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue. PPPoE: if you click PPPoE as the protocol, please manually enter the Username/Password provided by your ISP and all the required information. Then, click Next.
PPTP/L2TP: if you click PPTP/L2TP as the protocol, please manually enter the Username/Password provided by your ISP and all the required information. Then, click Next. 7. In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs (clients) will share the same Internet connection with other wired hosts via Vigor wireless router.
WEP: if you choose WEP as the security configuration, you have to specify encryption key and authentication mode. WPA-PSK: if you choose WPA-PSK as the security configuration, you have to specify WPA mode, algorithm and pre-shared key.
WPA-RADIUS: if you choose WPA-Radius as the security configuration, you have to specify WPA mode, algorithm, Radius server, Radius server port and Radius server secret respectively. WPS: if you choose WPS as the security configuration, you can press Start WPS PIN and Start WPS PBC to complete the wireless connection.
8. Click Next to continue. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Now, you can enjoy surfing on the Internet.
This page is left blank.
4. Trouble Shooting This section will guide you to solve abnormal situations if you cannot access into the Internet after installing the router and finishing the web configuration. Please follow sections below to check your basic installation status stage by stage. ¾ Checking if the hardware status is OK or not. ¾ Checking if the network connection settings on your computer are OK or not. ¾ Pinging the router from your computer. ¾ Checking if the ISP settings are OK or not.
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not Sometimes the link failure occurs due to the wrong network connection settings. After trying the above section, if the link is stilled failed, please do the steps listed below to make sure the network connection settings is OK. For Windows The example is based on Windows XP. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.draytek.com. 1.
4. Select Obtain an IP address automatically and Obtain DNS server address automatically. For MacOs 1. Double click on the current used MacOs on the desktop. 2. Open the Application folder and get into Network. 3. On the Network screen, select Using DHCP from the drop down list of Configure IPv4.
4.3 Pinging the Router from Your Computer The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most important thing is that the computer will receive a reply from 192.168.1.1. If not, please check the IP address of your computer. We suggest you setting the network connection as get IP automatically. (Please refer to the section 4.2) Please follow the steps below to ping the router correctly.
4.4 Checking If the ISP Settings are OK or Not Open WAN>>Internet Access page and then check whether the ISP settings are set correctly. Use the Connection Type drop down list to choose Static IP/DHCP/PPPoE/PPTP/L2TP for reviewing the settings that you configured previously.
For Static Users 1. Choose Static IP as the connection type. 2. Check if IP Address, IP Mask and IP Router are set correctly (must identify with the values from your ISP). For PPPoE Users 1. Choose PPPoE as the connection type. 2. Check if Username, and Password are set correctly (must identify with the values from your ISP).
For PPTP/L2TP Users 1. Choose PPTP/L2TP as the connection type. 2. Check if Username, Password, IP address, Subnet Mask are entered with correct values that you get from your ISP. 4.5 Backing to Factory Default Setting If Necessary Sometimes, a wrong connection can be improved by returning to the default settings. Try to reset the router by software or hardware. Warning: After pressing factory default setting, you will loose all settings you did before.
Hardware Reset While the router is running (ACT LED blinking), press the Factory Reset button and hold for more than 5 seconds. When you see the ACT LED blinks rapidly, please release the button. Then, the router will restart with the default configuration. After restore the factory default setting, you can configure the settings for the router again to fit your personal request. 4.
