i VigorIPPBX 3510 Quick Start Guid
VigorIPPBX 3510 Quick Start Guide ii
VigorIPPBX 3510 Quick Start Guide Version: 2.
Copyright Information Copyright Declarations Copyright 2010 All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: z Microsoft is a registered trademark of Microsoft Corp.
European Community Declarations Manufacturer: Address: Product: DrayTek Corp. No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 VigorIPPBX 3510 DrayTek Corp. declares that VigorIPPBX 3510 is in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
VigorIPPBX 3510 Quick Start Guide vi
Table of Contents 1. Introduction........................................................................................................... 1 1.1 Panel Explanation ...................................................................................................................... 2 1.2 Package Content........................................................................................................................ 4 2. Installing Your Router..........................................................
VigorIPPBX 3510 Quick Start Guide viii
1. Introduction The VigorIPPBX 3510 is a dual-WAN broadband router with IP PBX function. The 2nd WAN interface is shared with the 4th LAN port. These two WANs can connect to DSL/Cable modem or fiber media converter for policy-based load-balance, fail-over and BoD (Bandwidth on Demand); it also features advanced bandwidth control mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable access control and bandwidth management.
1.1 Panel Explanation Description for LED LED Status Explanation PWR (Power) On Off Blinking Off On Blinking On Off The router is powered on. The router is powered off. The router is powered on and running normally. The router is not ready or failed. The WAN connection is ready. It will blink while transmitting data. CDR utility has been installed and is recording. CDR utility has not been installed and is unable to record. A USB device is connected and active. The data is transmitting.
Description for Connectors Interface Factory Reset FXS FXO LAN (1-4) WAN USB PWR ON/OFF Description Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connecter for telephone set. Connecter for FXS interface of PABX or PSTN line. Connecters for local networked devices.
1.2 Package Content n Quick Start Guide o CD p RJ-45 Cable (Ethernet) q Rack mount kit (brackets) r FXO (optional) sFXS (optional) tThe type of the power cord depends on the country that the router will be installed.
2. Installing Your Router This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. 2.1 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. 1. Connect the cable Modem/DSL Modem/Media Converter to WAN port of router with Ethernet cable (RJ-45). 2.
2.2 Printer Installation You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000/Vista. For Windows 98/SE, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers. 1. Connect the printer with the router through USB/parallel port. 2. Open Start->Settings-> Printer and Faxes.
3. Open File->Add a New Computer. A welcome dialog will appear. Please click Next. 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next.
6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish.
9. Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next. 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new printer you have added. 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and LPR name.
The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional functions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.
3. Configuring Web Pages To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly.
Note: The home page will change slightly in accordance with the router you have. 4. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue. 5. On the next page as shown below, please select the WAN interface (WAN 1 or WAN2) that you use. If WAN1 interface is used, please choose WAN1; if WAN2 interface is used, please choose WAN2. Choose Auto negotiation as the physical type for your router. Then click Next for next step.
6. On the next page as shown below, please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step. PPPoE: if you click PPPoE or PPPoA as the protocol, please manually enter the Username/Password provided by your ISP. Then click Next.
PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type in all the information originally provided by your ISP. Then click Next for next step. Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step.
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue. 7. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet.
This page is left blank.
4. Trouble Shooting This section will guide you to solve abnormal situations if you cannot access into the Internet after installing the router and finishing the web configuration. Please follow sections below to check your basic installation status stage by stage. ¾ Checking if the hardware status is OK or not. ¾ Checking if the network connection settings on your computer are OK or not. ¾ Pinging the router from your computer. ¾ Checking if the ISP settings are OK or not.
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not Sometimes the link failure occurs due to the wrong network connection settings. After trying the above section, if the link is stilled failed, please do the steps listed below to make sure the network connection settings is OK. For Windows The example is based on Windows XP. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.draytek.com. 1.
4. Select Obtain an IP address automatically and Obtain DNS server address automatically. For Mac OS 1. Double click on the current used Mac OS on the desktop. 2. Open the Application folder and get into Network. 3. On the Network screen, select Using DHCP from the drop down list of Configure IPv4.
4.3 Pinging the Router from Your Computer The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most important thing is that the computer will receive a reply from 192.168.1.1. If not, please check the IP address of your computer. We suggest you setting the network connection as get IP automatically. (Please refer to the section 4.2) Please follow the steps below to ping the router correctly.
4.4 Checking If the ISP Settings are OK or Not Open Internet Access page and then check whether the ISP settings are set correctly. For PPPoE Users 1. Check if the Enable option is selected. 2. Check if Username and Password are entered with correct values that you got from your ISP.
For Static/Dynamic IP Users 1. Check if the Enable option is selected. 2. Check if Obtain an IP address automatically for Dynamic IP setting is selected. Or check if IP address, Subnet Mask and Gateway are entered with correct values for Static IP setting that you got from your ISP. For PPTP/L2TP Users 1. Check if the Enable option for PPTP/L2TP Link is selected. 2. Check if Server, Username, Password and WAN IP address are set correctly (must identify with the values from your ISP).
4.5 Backing to Factory Default Setting If Necessary Sometimes, a wrong connection can be improved by returning to the default settings. Try to reset the router by software or hardware. Warning: After pressing factory default setting, you will loose all settings you did before. Make sure you have recorded all useful settings before you pressing. The password of factory default is null. Software Reset You can reset the router to factory default via Web page.
4.6 Contacting Your Dealer If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.
