UNIDOOR X (STYLE M1) SHOWER DOOR & GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com STYLE M1 STEP 1: Install Shower Door STEP 2: Install Panel For more information about DreamLine Shower Doors, Tub Doors and Enclosures, please visit DreamLine.
©2017 DreamLine. All Rights Reserved UNIDOOR-X Style M GLASS-TO-GLASS HINGE SHOWER DOOR INSTALLATION IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Right Hand Door installation shown For more information about DreamLine® products please visit DreamLine.
©2017 DreamLine. All Rights Reserved This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially-formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a soft cloth.
Model Numbers ©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Unidoor-X Style M manual used with the following Model Styles: Style L1 Style M Style M2 Style M1 ! Style M4 Style M3 When installing one of the configurations shown above with glass-to-glass hinges, discard the Style A manual that is packaged with the door glass and use this Style M manual for the installation of the hinge panel glass and door glass.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2017 DreamLine. All Rights Reserved Tools Level Drill bit (Ø=5/16") Metal File Tape Measure Drill bit (Ø=1/8") Silicone* Pencil Phillips Screwdriver Power Drill Miter saw Hammer or Hacksaw *Quick-drying/fast curing silicone recommended for the installation of hinge panels.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Installation steps Style M - 6” & 24” Inline Panel and Shower Door Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR Style M, M1, M2, M3, M4 and L1 models. Before you begin the installation, please check your finished opening size and model dimensions to ensure proper placement of the Hinge Panel Glass (#32) and Door Glass (#01).
©2017 DreamLine. All Rights Reserved Installation steps for 6” hinge panel with Hinge Panel Glass Bracket 1. Draw a line on the threshold and on 2. Cut the vertical U-channel to 69-7/16”. Cut the bottom U-channel** to 6”. (Fig 4) the wall to represent the centerline of the U-channel. Make sure the line is parallel to the front edge of the threshold.
©2017 DreamLine. All Rights Reserved 3. Position the U-channels and Hinge Panel Glass Bracket (#36) on the centerlines to mark the holes for drilling. (Fig 5) Fig 5 UNIDOOR-X (STYLE M) manual Ver 2 11/2016 4. Mark the hole positions on the centerline on the wall and threshold through the holes in the U-channels and the Hinge Panel Glass Bracket (#36). (Note that the Hinge Panel Glass Bracket (#36) is wider than the u-channel).
©2017 DreamLine. All Rights Reserved 5. Drill Ø5/16” holes in the wall and install the wall anchors. Drill Ø1/8” holes into an acrylic threshold (or Ø5/16” holes and anchors for a tile threshold). (Fig 7) 6. Apply silicone to the back of the U-channels and the screw holes, then install the U-channels and Hinge Panel Glass Bracket (#36) using the ST4.2 x 40mm screws (#23).
©2017 DreamLine. All Rights Reserved 7. Add the 0.5mm shims into the bottom U-channel to protect the bottom corners of the glass. Apply a bead of silicone into the length of the U-channels. (Fig 9) Quick-drying/fast curing silicone is recommended for the installation of hinge panel glass into u-channels. 8. Install the Hinge Panel Glass (#32) into the U-channel, checking for level and plumb. Install the gasket into the Hinge Panel Glass Bracket.
©2017 DreamLine. All Rights Reserved 9. Tighten the rubber-tipped set screws on the Hinge Panel Glass Bracket (#36) to secure the glass. Do Not overtighten! (Fig 11) insi de ! Fig 11 NOTE: Following the installation of the Hinge Panel Glass (#32), it is strongly recommended that the silicone be allowed to fully cure before hanging the door glass. (Fig 12) Go to Step #18 on Page 21 to continue the installation of the Hinges, Door Glass and other components.
©2017 DreamLine. All Rights Reserved Installation steps for 24” hinge panel glass with L-Bracket 10. Cut the vertical U-channel 1 (#09) to 71”. (Fig 13) U-Channel 1 L Fig 13 11. Cut the bottom U-channel 2 (#29) to 24” (see note** below).
©2017 DreamLine. All Rights Reserved 12. Position the U-channel 2 (bottom profile) (#29) onto the threshold, parallel to the outside edge. Mark the position of the U-channel and mark the position of the holes for drilling. You need to use at least 3 holes for the U-channel 2 (bottom profile) (#29): one near each end and one near the center. • Drill the holes into the threshold using an Ø1/8” drill bit.
©2017 DreamLine. All Rights Reserved 13. Next, position the vertical U-channel 1 (#09) (wall 2 1 profile) on top of the installed bottom U-channel. Use a level to plumb the U-channel 1 (#09) (wall profile) and mark the positions of the holes for drilling. You need to use at least four holes for the U-channel 1 (#09) (wall profile). • Drill the holes into the wall using a Ø5/16” drill bit. • Insert the Wall Anchors (#13) into the 5/16” holes.
©2017 DreamLine. All Rights Reserved NOTE: There is a top and a bottom to the Hinge Panel Glass (#32): The top hinge cutout is 7-7/8” to center, the bottom hinge cutout is 8-3/8” to center. The hinge panel glass must be installed correctly so that the door glass can be installed correctly. 15. Install the Hinge Panel glass (#32) into the U-channel 2 (#29) (bottom profile) and the U-channel 1 (#09) (wall profile). Apply a dab of silicone to the exposed end of the bottom u-channel.
©2017 DreamLine. All Rights Reserved Installation steps for 24” hinge panel glass with L-Bracket L- Bracket Assembly Parts List** 35.9 35.4 35.5 35.3 35.6 35.2 35.1 35.7 35.8 35.1 35.2 35.3 35.4 35.5 PVC spacer Rubber tip set screw L-Bracket (left hand shown) Decorative cover Ø5/16” Wall anchor 1 pc 2 pcs 1 pc 1 pc 6 pcs 35.6 35.7 35.8 35.9 Wall plate Truss Head Screw ST 4.
©2017 DreamLine. All Rights Reserved (Left-hand bracket installation shown) 16. Position the L-Bracket assembly (#35) onto the Hinge Panel Glass (#32) as shown and mark its position on the wall. Remove the Wall Plate (#35.6) from the L-bracket. Hold the Wall Plate (#35.6) to the marks on the wall. Check for level and mark the holes for drilling through the wider, untapped holes. (Fig 20.2) Drill two Ø5/16”(8mm) holes and insert the Ø5/16” Wall anchors (#35.5). (Fig 20) 1 2 3 4 Ø5/16" (8mm) Fig 20 17.
©2017 DreamLine. All Rights Reserved 18. Adjust the Stationary Glass to plumb and tighten the screws. Attach the Decorative Cover (#35.4). Secure the L-Bracket (#35.5) to the top of the Stationary Glass using the clear gasket and rubber-tipped set screws. Do not overtighten! (Fig 22) 9 /16 0-1 m) 11 10 m ”(2 Fig 22 Left-hand bracket installation Fig 23 Right-hand bracket installation NOTE: The left-hand L-bracket installation is shown.
©2017 DreamLine. All Rights Reserved 19. Attach the Hinges (#05) to the Hinge Panel Glass (#32) with the bolts facing inside the shower. Install the hinges onto the Hinge Panel Glass (#32) flush with the edge of the glass. Use at least one 2mm hinge gasket per side. Tighten the hinge bolts evenly and snap in the decorative bolt caps.
©2017 DreamLine. All Rights Reserved 20. The Door Glass (#01) ships with four 1 5/8” spacers attached to the top (2pcs) and bottom (2pcs). These 5/8” spacers will create the proper spacing at the bottom of the door glass and will ensure the installed door height finishes at 72”, but always 5/8” confirm with a measurement. 2 door glass 3 inside door glass outside Set the Door Glass (#01) with the 5/8“ spacers attached onto the threshold, inline with the Hinge Panel Glass (#32).
©2017 DreamLine. All Rights Reserved 22. Measure the bottom of the Door Glass (#01) from side to side to determine the actual width of the door. Cut the Bottom Anti-Water Strip (#07) to the size of your measurement and notch 3/8” of the inner side of the Bottom Anti-Water Strip (#07) as shown in Fig 27.2. Press the Bottom Anti-Water Strip (#07) onto the bottom edge of the Glass Door (#01).
©2017 DreamLine. All Rights Reserved For Style M only: If your model does not include additional panel glass, proceed to the next step to install the L-shaped Strip (#08) to the wall. 1 Inside shower ATTENTION: Prior to the next step, please be sure the section of the wall where you need to attach the L-shaped Strip (#08) is clean, dry, and free from soap, oil or any construction debris. 24. With the door closed, place the L-shaped Strip (#08) on the door edge and mark its location on the wall.
©2017 DreamLine. All Rights Reserved 25. With the door open, apply a good quality mildew-resistant/waterproof silicone along the connection of both U-Channels to the wall and threshold on the inside of the shower. NOTE: The surface needs to be clean and free of debris before applying silicone. Let the silicone cure before closing the door to avoid contact with the Bottom anti-water strip (#33) (Fig. 31) Fig 31 26. Allow 24 hours for the silicone to fully cure before using the shower.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2017 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
©2017 DreamLine. All Rights Reserved UNIDOOR PLUS (STYLE F) SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Style F Style F Right side panel installation shown ATTENTION: This model is also available with the Half Frosted Band glass option.
©2017 DreamLine. All Rights Reserved Style “F”: Half Frosted Band Glass Installation NOTE: This model features the half frosted glass option. Hinged Left installation shown. To install for hinged Right, flip the door and panel to the proper handing. NOTE: The textured surface of both the stationary glass and door glass should face outside of the shower. Hinged Left installation UNIDOOR PLUS (STYLE F) manual Ver.
©2017 DreamLine.
©2017 DreamLine. All Rights Reserved ADDITIONAL MODEL CONFIGURATIONS for UNIDOOR-X GLASS-TO-GLASS HINGE DOORS Model#s: D12306572-## D1230672 D12314572 D1231472 D12322572 D1232272 D12330572 D1233072 D12406572 D1240672 D12414572 D1241472 D12422572 D1242272 D12430572 D1243072 D12506572 D1250672 D12514572 D1251472 D12522572 D1252272 Finishes: -01 = Chrome -04 = Brushed Nickel -06 = Oil Rubbed Bronze -09 = Satin Black UNIDOOR PLUS (STYLE F) manual Ver.
©2017 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2017 DreamLine. All Rights Reserved Tools Required Caulk Level Tape Measure Caulk Gun UNIDOOR PLUS (STYLE F) manual Ver.
©2017 DreamLine. All Rights Reserved Detailed Diagram of Glass Panel Components 9 11 13 23 19 20 The glass surface with the ClearMax™ label must be installed to face inside of the shower 29 Packing List 09 11 13 19 U-channel 1 (76”, wall profile) Stationary glass Ø5/16” Wall anchor Anti-Water strip (inline panel) 1pc 20 1pc 23 14pcs 29 1pc Anti-Water strip (enclosure) * Countersunk screw ST4.2x40 U-channel 2 (44”, bottom profile) 1pc 14pcs 1pc NOTE: Unpack your unit carefully and inspect it.
©2017 DreamLine. All Rights Reserved Style “F”: 6”-34” In-Line Stationary Panel Installation NOTE: The Unidoor shower door needs to be installed prior to proceeding with the following Stationary Glass installation instructions. Please see the Single Shower Door installation manual in the door packaging (or the Style M Glass-to-Glass hinge door installation manual included with the hinge panel glass) for complete shower door installation instructions.
©2017 DreamLine. All Rights Reserved NOTE: Use parts from “Detailed Diagram of Glass Panel Components” for the Stationary Glass assembly and installation. 2. Measure the actual width of your stationary glass panel. NOTE: You will be doing straight cuts for this stationary panel installation. *It may be necessary to remove any burrs from the cut end of the U-channels with a metal file before placing the Uchannel onto the glass.
©2017 DreamLine. All Rights Reserved 3. Slip the cut U-channel 2 (44”, bottom profile) (29) and uncut U-channel 1 (76”, wall profile) (09) onto the Stationary glass (11) in the shown locations. With the door open place the Stationary glass on threshold opposite of door. Adjust the Stationary glass and U-channel 1 (wall profile) against the wall to compensate for any out of plumb conditions ensuring that the Stationary glass is level vertically and U-channel 1 is flush with the wall.
©2017 DreamLine. All Rights Reserved 5. Remove the U-channel 1 (76”, wall profile) (09), U-channel 2 (44”, bottom profile) (29) and Anti-Water strip (inline panel) (19) from the Stationary glass (11) and set the Stationary glass aside. Place the U-Channel 2 (bottom profile) onto the threshold base in line with the inside threshold mark. Mark the drill holes on the threshold through the predrilled holes in the UChannel 2 and drill the holes using Ø1/8” drill bit.
©2017 DreamLine. All Rights Reserved 6. Cut the U-channel 1 (76”, wall profile) (09) at the top mark that was made in step #4. 1 Place the U-Channel 1 (wall profile) on the U-Channel 2 (44”, bottom profile) (29) and align vertically with wall mark. U-Channel 1 2 U-Channel 2 3 Mark the drill holes on the wall through the predrilled holes in the U-Channel 1. Now drill holes in the wall using Ø5/16 drill bit and insert the Ø5/16” Wall anchors (13). 4 Ø5/16” 5 See Fig. 8 for details. Fig. 8 7.
©2017 DreamLine. All Rights Reserved Fig. 10 8. Slide the Stationary glass (11) into the groove of both U-Channels. NOTE: If you have difficulty sliding the Stationary glass into the U-Channels, you can slightly tap on the Stationary glass with a rubber mallet and a piece of wood. 1 2 3 4 Apply a bead of silicone on both open ends of the U-Channels, and its connection. See fig. 11 for details. Fig. 11 UNIDOOR PLUS (STYLE F) manual Ver.
©2017 DreamLine. All Rights Reserved 9. Apply a good quality mildew-resistant waterproof silicone along the connection of both U-Channels to the wall and threshold on the inside of shower. Allow 24 hours for the silicone to fully cure before using the shower. See Fig. 12 for details. waterproof silicone inside Fig. 12 10. Notch the Anti-Water strip (inline panel) (19) 1” at the base to fit around bottom U-channel.
©2017 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2017 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com UNIDOOR PLUS (STYLE F) manual Ver.
