Aqua Shower Door & Base Kit SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up -to-date technical drawings, manua ls or any other details please refer to the support.BathAuthority.com web page.
AQUA SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Shower Door and Tub Door Component 1 7 8 9 3 2 4 5 10 11 6 12 13 14 15 Packing List 01 02 03 04 05 06 07 08 Wall profile Stationary glass Support bar Hinge Glass door Towel bar Wall anchor Decorative caps 1pc 1pc 1pc 2pcs 1pc 1pc 5pcs 2pcs 09 10 11 12 13 14 15 Round Head screw ST4.2×10 Big head screw ST4.2×40 Anti-Water strip Bottom anti-water strip Round head screw ST4.2×25 Bottom bracket Countersunk screw ST4.
Shower/Tub Door Installation 1. Place the Wall profile (01) to the wall above the shower base or tub and level it vertically. See Fig. 1 for details. Fig. 1 2. Mark the drilling holes on the wall through the holes in the Wall profile (01). Place the Wall profile aside, drill the holes using Ø5/16” drill bit and insert the Wall anchors (07). Apply silicone caulk along the wall profile and around the holes on the wall.
3. Slide the Stationary glass (02) into the groove of the Wall profile (01). See Fig. 3 for details Fig. 3 4. Take apart the Bottom bracket (14). Place the Bottom bracket base into the notch on the bottom of the Stationary glass (02) from inside and mark the drill hole on the threshold, tray or bathtub. Remove the glass, drill the hole using Ø1/8” drill bit and secure the Bottom bracket base with Round head screw ST4.2×25 (13). See Fig. 4 for details. 1 3 Inside Ø1/8" Outside 2 4 Fig. 4 “AQUA” Rev.
5. Place the Stationary glass (02) back into the Wall profile (01) and assemble the Bottom bracket (14). See Fig. 5 for details. NOTE: Make sure to use clear rubber gasket to prevent glass to metal connection. Fig. 6 Fig. 5 6. Locate the Support bar (03). Adjust the Support bar at the angle that will provide adequate support to the glass and the wall. Level it horizontally. Hold it firmly and outline the bracket’s position on the wall. Remove the Support bar and detach the wall bracket from it.
7. Install both Hinges (04) on the Stationary glass (02) with the decorative non-screw side facing outwards. Hang the Glass door (05) from the inside. You will need assistance in this process. NOTE: Use 5/8” shim beneath the glass door to hold it in position while you attach the hinges. NOTE: Use clear rubber gasket to prevent glass to metal connection. Inside Outside 1 Begin at the top hinge when hanging the door.
8. Install the Towel bar (06) onto the Glass door (05). Attach the Anti-water strip (11) over the vertical edge of the Glass door (05). Attach the Bottom anti-water strip (12) over the bottom edge of the Glass door. 1 3 Door Outside Inside Outside See Fig. 9 for details. 2 Inside Panel Outside Door Fig. 9 9.
. Apply caulk inside and outside along bottom and vertical edge of the stationary glass and wall profile. See Fig. 11 for details. Caulk Fig. 11 Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on BathAuthority.com Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration W W1 11 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1132320 DLT-1136360 32"×32" 36"×36" 32" 36" 32" 36" 15" 15" 16" 18" DLT-1134420 34” x 42” 34” 42” 15” 21” DLT-1132480 DLT-1136480 DLT-1130600 DLT-1132600 DLT-1134600 DLT-1136600 32"×48" 36"×48" 30"×60" 32"×60" 34"×60" 36"×60" 32” 36" 30" 32" 34" 36" 48” 48" 60" 60" 60" 60" 15” 15" 15" 15" 15" 15" 24” 24" 30" 30" 30" 30" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130601 DLT-1132601 DLT-1134601 DLT-1136601 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130602 DLT-1132602 DLT-1134602 DLT-1136602 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
NEO ANGLE SHOWER BASE W C C A W B A MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2036360 DLT-2038380 DLT-2040400 DLT-2042420 36"×36" 38"×38" 40"×40" 42"×42" 36" 38" 40" 42" 18 5/16" 20 5/16" 22 5/16" 24 5/16" 25" 25" 25" 25" 12" 12" 14 3/8" 14 3/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
QUARTER ROUND SHOWER BASE W C C W R MODEL SPECIFICATION W (in) C (in) R (in) DLT-7033330 DLT-7036360 DLT-7038380 33"×33" 36"×36" 38"×38" 33" 36" 38" 12" 12" 12" 21 5/8" 21 5/8" 21 5/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration W C C W MODEL SPECIFICATION W (in) C (in) DLT-1032320 DLT-1036360 32"×32" 36"×36" 32" 36" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034481 DLT-1036481 DLT-1036601 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034482 DLT-1036482 DLT-1036602 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Cross Section Diagram Shower Base Cement board Finished Wall (2"×4") Stud Mortar Drain “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig. 4 “SLIMLINE SHOWER BASE” Ver.5 Rev.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig. 6 “SLIMLINE SHOWER BASE” Ver.5 Rev.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-857-3638 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Bases please visit www.BathAuthority.
