INFINITY-Z TUB DOOR & BACKWALL INSTALLATION INSTRUCTIONS Wall Profile with Flange OR STEP 1: Tub Backwall Installation Instructions STEP 2: Tub Door Installation Instructions ! Wall Profile without Flange CHOOSE the APPROPRIATE MANUAL for your model version Wall Profile WITH Flange: INFINITY-Z Manual Ver 4 Rev 5 062017 OR Wall Profile WITHOUT Flange: INFINITY-Z Manual Ver 5 Rev 2 012020 1-866-731-2244 For more information about DreamLine® products please visit DreamLine.
Q-WALL TUB BACKWALL ACRYLIC BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com MODEL #s SHBW-1360603-01 For more information about DreamLine® Shower Doors, Tub Doors & Enclosures, please visit DreamLine.
Table of Contents Page # Section title Preparation Tools 2 Detailed Diagram of Shower Wall Components 4 Parts List 5 Installation Steps 6-18 Tub Glass Shelves Installation (optional) 19 Product Maintenance 21 3 Overall Dimensions 56 "-- -6 0" 56"--- 60" 60" Q-Wall Tub manual Ver 1 Rev 2 11/2017 28"--- 32" 28 28"--- 32" 2" -3 "-- ©2017 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Tape Measure Level T-Square Hole Saw Caulk Pencil Power Drill Knife Hammer Drill bit (Ø 5/16") Phillips Screwdriver (acrylic safe) Adhesive to be sure that the correct model size has been ordered. ! Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. ! Tip: Set screw gun clutch to low setting when installing screws and bolts to prevent stripping the heads. ©2017 DreamLine.
Detailed Diagram of Shower Wall Components 4 1 3 2 5 6 7 8 9 ©2017 DreamLine.
Parts List ITEM # PART NUMBER DESCRIPTION QTY 030006 Side panel 2pcs 02 030005 Back panel 2pcs 03 060006000-1524 Decorative edge molding 2pcs 04 04059021-1524 Corner cover 2pcs 05 04058021-1524 Center cover 1pc 06 07550045 Wall anchor 21pcs 07 091101 Countersunk screw ST4.2×30 21pcs 08 07552010 Decorative cover 15pcs 09 017000001 Glass shelf 2pcs 10 07011029 Shelf bracket 6pcs ©2017 DreamLine.
Installation steps 1. Measure the distance of the back wall of W the tub from corner to corner. Record this measurement as “W”. (Fig 1) W W Fig 1 2. Divide the “W” measurement in half (W/2). W/2 Draw a plumb line to mark the center of the back wall (Fig 2) ©2017 DreamLine.
3. Measure the side walls from the corner to the front point where the Side Panel (#01) will be trimmed to size. Record this measurement as “D”. (Fig 3) D D Fig 3 Draw plumb Vertical Reference lines 1” from the corners 4a. Measure 1” from the corners and draw plumb, ©2017 DreamLine. All Rights Reserved vertical reference lines on the walls at both corners.
4b. Measure the location of the holes on the wall S = (D-1”) where the fixtures will be installed. Use these measurements to drill the cutouts in the corresponding Side Panel (#01) in Step #17. 1" A back Take exact measurements: corner of walls • from the vertical reference line to the center of the fixture holes: (A, B, C, G) • from the tub deck up to the center of the fixture holes: (E, F, H).
5. Place the Center Cover (#05) vertically on the back wall centerline (from Step#2) and mark the drilling holes through the predrilled holes in the Center Cover (#05). Drill the holes using a Ø5/16” drill bit and insert the Wall Anchors (#06). (Fig 5a and Fig 5b) 1 2 3 4 Ø5/16” Fig 5a Fig 5b 6. Place the Corner Cover (#04) to the corner of the wall and mark the drilling holes through the 1 2 3 4 ©2017 DreamLine. All Rights Reserved predrilled holes in the Corner Cover (#04).
1” reference line 7. Determine the finished cut size for both Back Panels (#02). centerline (If the finished overall width of the back wall= 59-1/2” from corner-to-corner, then it will not be necessary to trim the back panels. Proceed to Step #9). L NOTE: (a) = Narrow edge (3-3/8”) toward the center line on the back wall. (do not trim this edge) (b) = Wider edge (4-5/8”) toward the corner of the back wall.
8. Place the Back Panel (#02) onto a flat piece of plywood or particle board. Use a T-square and a sharp industrial knife to score along the cut lines (from the previous step) on the Back Panel (#02) and continue scoring until fully cut through the panel. (Fig 8a and Fig 8b) 2 1 L L a Fig 8a Fig 8b 9. Install the Center Cover (#05) to the center of the back wall using the Countersunk Screws ST4.2×30 (#07). Do not fully tighten the screws yet. Leave the Center Cover (#05) loose on the wall for now.
11. Slide the right edge of the left Back Panel (#02) behind the Center Cover (#05) and push the Back Panel (#02) flat against the wall up to the 1” vertical reference line in the corner. Adjust the position of the Back Panel (#02) before the adhesive sets. Apply equal pressure to the whole surface of the Back Panel (#02) from top to bottom. Fasten the Corner Cover (#04) to the left corner of the backwall using the Countersunk Screws ST4.2×30 (#07). Do not fully tighten the corner cover screws yet.
13. Align both Back Panels (#02) at the top and tighten the screws on the Center Cover (#05) to secure this assembly in place. Do not tighten the screws on the corner covers yet. (Fig 13a and Fig 13b) 1 2 Fig 13b Fig 13a 1” reference line Trim line S Note: Refer to the “D” dimension from Step #3 to determine the finished cut size “S” for the Side Panel (#02) in the next steps. (D - 1” = S) 14. Measure from the 1” reference line to the D ©2017 DreamLine.
15. Mark the finished cut size “S” for both Side these edges to the corners Panels (#01). NOTE: (a) = Narrow edge (3-3/8”) toward the corner reference line (do not trim this edge) S S (b) = Wider edge (6-3/8”) toward the outside of the side wall. (trim this edge only) Trim the side panels to the “S” dimension, cutting from the wider edge (b) of the side panels only.
. Transfer the fixture hole measurements (from Step #4) onto the Side Panel (#01) that will be installed onto the wall with the fixtures. Drill the holes in the Side Panel (#01) using the appropriate diameter hole saw or a handheld jig saw. (Fig 17a and Fig 17b) Hole Saw ! NOTE: Be sure to drill the holes on the correct surface of the side panel to match the dimensions from Step#2 Fig 17a Fig 17b Right side wall fixtures shown as an example 18.
19. Slide the edge of the Side Panel (#01) behind the Corner Cover (#04) and push the Side Panel (#01) flat against the wall up to the vertical reference line toward the outside of the tub (Fig. 19a.3). Align the top of the Side Panel (#01) with the Back Panel (#02) before the adhesive sets. Apply equal pressure to the whole surface of the Side Panel (#01) from top to bottom.
21. Repeat Step#18 to install the second Side Panel (#01), tucking the Side Panel (#01) behind the corner cover and fully tightening the screws. (Fig 21a and Fig 21b) 1 2 3 4 Fig 21a Fig 21b 22. Tighten the screws for the Corner Covers (#04) and the Center Cover (#05) to secure the Side Panels (#01) and the Back Panels (#02) in place. (Fig 22) ©2017 DreamLine. All Rights Reserved Fig 22 23.
24. Apply a good quality mildew-resitant caulk or silicone along the top edge of the panels and corner covers and along the connection of the bottom edges of the panels with the tub. (Fig 24) ! Allow 24 hours for the adhesive and silicone/caulk to cure before using the shower. 24 Hours Fig 24 To install the optional Glass Shelves (#09), continue onto the next steps. ©2017 DreamLine. All Rights Reserved ! ATTENTION: The installation of the Q-WALL-Tub walls is complete.
Glass Shelves Installation Instruction (optional) 25. Determine the preferred height for the Glass Shelves (#09) and mark the locations on the wall. (Fig 25) NOTE: Both Glass Shelves can be installed in one corner, or one shelf in each corner. G H Fig 25 26. Mark the location for the Shelf Brackets (#10) according to the measurements in Fig 25.1. Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (#06). (Fig 26) 1 2 3-1/2" 3-1/2" 3 ©2017 DreamLine.
27. Mount the Glass Brackets (#10) to the wall using the Countersunk Screws ST4.2×30 (#07). NOTE: The Glass Brackets (#10) should be installed with the set screws on the bottom. Slide the upper Glass Shelf (#09) into the Glass Brackets (#10) and tighten the set screws at the bottom of the brackets. Then slide the bottom Glass Shelf (#09) into place and tighten the set screws. (Fig 27a and Fig 27b) 1 2 3 Fig 27a ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2017 DreamLine.
INFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Table of Contents Section title Preparation Tools Parts List Installation Steps Wheel Assemblies Vinyl Seals Product maintenance INFINITY-Z manual Ver 4 Rev 5 06/2017 Page # 2 3 5 6-13 11 12 14 ©2017 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Silicone/Caulk Tape Measure Phillips Screwdriver Pencil Power Drill Drill bit (Ø=5/16") (D=8mm) Drill bit (Ø=1/8") (D=3mm) Miter saw or Hacksaw Hammer Top Tip: Measure the finished opening before Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. Tip: Set screw gun clutch to low setting when installing screws and bolts to prevent stripping the heads. Middle Bottom W ©2017 DreamLine.
Detailed Diagram of shower door components 13 8 14 12 11 10 2 1 9 5 15 16 3 7 18 4 6 ©2017 DreamLine.
Parts List DESCRIPTION QTY PART# DESCRIPTION QTY 01 Glass profile 2pcs 10 Round head screw ST4.2x25 8pcs 02 Wall profile 2pcs 11 Round head screw ST4.2x10 4pcs 03 Guide rail (top and bottom) 2pcs 12 Flat head screw ST4.
Installation steps 1. Measure the distance between the two finished walls at the top (at model height: 58” or 72”), middle and bottom. The wall profiles will adjust for out-of-plumb conditions, so use the smallest measurement as the “finished opening” dimension to determine the finished cut length in Step #2. (Fig 1) NOTE: The Top and Bottom Guide Rails (#03) are shorter than the model size by design.
3. After the Top and Bottom Guide Rails (#03) have been cut, you will need to re-install the roller stopper on each Top and Bottom Guide Rails (#03) on the end that has been cut off (the door end). Remove the existing stopper. Mark the drilling hole at the distance of 3-1/8” from the cut end of the Top and Bottom Guide Rails (#03). Drill a new hole using a Ø1/8” drill bit; then re-secure the stopper with the screw.
5. Slide the Stationary Glass (#05) fully into the groove of the Glass Profile (#01), and then secure the Glass Holder (#16) to the Bottom Guide Rail (#03) with the Flat Head Screw ST4.2x16 (#12). (Fig 6) ! NOTE: Use caution when installing the stationary glass into the frame to prevent damage to the edges of the glass. Bottom rail cut away to show detail Inside add a bead of silicone to the bottom rail (optional) prior to installing the stationary glass Fig 6 6.
8. Slide the Wall Profiles (#02) all the way onto the Glass Profiles (#01) on both sides. Make sure the flange of the wall profile faces inside the shower. (Fig 8) Inside Fig 8 9. Move the assembled frame into the designated position on the shower base*, bathtub or threshold (depending on your installation), and push the Wall Profiles (#02) tight to the walls to compensate for any out-of-plumb conditions. Push the bottom rail down tight to the threshold and adjust the frame to a vertical position.
10. Use a helper to hold the assembly in position and mark the drill holes on the wall through the holes on the flange of the Wall Profiles (#02). Gently set the assembled unit aside; drill the holes using a Ø5/16” drill bit and insert the Wall Anchors (#14). Apply silicone along the Wall Profile (#02) and around the holes on the wall. Also apply silicone caulk under the Bottom Guide Rail (#03).
12. Fasten the top and the bottom Wheel Assemblies (#17) to the Door Glass (#04). The top wheels can adjust the door level using the adjustable bolt and lock nut. The bottom wheel has a press button to fix the wheel onto the Bottom Guide Rail (#03). The wheels must face towards the outside of the shower. Be sure that the handle holes are on the correct side for the installation. (Fig 12) NOTE: The lock nut of the upper wheel (Fig 12.4) and the press button of the bottom wheel (Fig 12.
14. Install the Handle (#06) to the Door Glass (#04). Press the Anti-Water Strips (#07) onto the vertical edges of the Stationary Glass (#05) and both vertical edges of the Door Glass (#04). Insert the Seal Gasket (#15) into the Glass Profile (#01) starting from the bottom (Fig. 14.3). (Fig 14) 1 2 3 Outside Fig 14 TIP: The longer Anti-Water Strips (#07) attach to the edges of the Door Glass (#04) and the shorter strip attaches to the edge of the Stationary Glass (#05). 15.
16. Apply good quality mildew-resistant silicone along the profiles and guide rails; on the seams between the bottom guide rail and the profiles as well as along the shower base or threshold. Allow 24 hours for the silicone to cure before using the shower. (Fig 16) ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2017 DreamLine.
INFINITY-Z ® SHOWER AND TUB DOOR INSTALLATION d INSTRUCTIONS e e n v i r LMANUALsPRIOR PLEASE REVIEW THIS ENTIRE TO INSTALLATION e m e a R e Dr ghts © Ri l l A MODEL #s SHDR-0960580-## d e e n v i r L e s m e a R e r s D ght © Ri All MODEL #s SHDR-0948720-## SHDR-0954720-## SHDR-0960720-## Left-hand door installation shown ® ## = finish 01-Chrome 04-Brushed Nickel 06-Oil Rubbed Bronze FR-Frosted Glass IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time without
d e e n v i r L e s m e a R e r s D ght © Ri All ® Record the following purchase information for your records or in the event you need to contact DreamLine®: Purchase Order Number Store/Vendor Purchased From Installation Date OD Number (optional) Installed By: SKU Number INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 located on the shipping box or label if available.
Section Title General Preparations and Warnings Model Specific Preparation Adjustable Wall Profile System Tools Detailed Diagram of Shower Door Components Parts List Installation Steps Top and Bottom Roller Assembly Installation Handle and Vinyl(s) Installation Decorative Cover with Washer Installation Product Maintenance Troubleshooting Factory Parts Information d e e n v i r L e s m e a R e r s D ght © Ri l l A ® d e e n Symbol Legendi v r L e s m e a R e r s D ght © Ri All Page # 2 3 4 5 6 7-8 9-24 20
d e e ® n i e erv ed L s m n v e i r a L R e e Dr regahmts Res © DRi hts ©All Rig l l A IMPORTANT • GENERAL PREPARATION • • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2020 DreamLine® All Rights Reserved Model Specific Preparation 1” Out-of-Plumb Adjustment; Verify threshold and walls with a level Threshold must be level 1” minimum threshold d e e n v i r L e s m e a R e r s D ght © Ri l l A ® ±0.0 1” (25.4mm) minimum flat threshold ±0.0 ! Threshold must be level ! DO NOT attach the handle and/or towel bar to the glass until instructed to do so. DO NOT attempt to use the handle/towel bar to lift the glass during installation.
©2020 DreamLine® All Rights Reserved Adjustable Wall Profile System ! Wall Profile The Glass Profiles can be adjusted within the Wall Profiles for overall width or to correct for out-of-plumb conditions within the model size. Screw them together after making final adjustments. ® Glass Profile d ® e e n iine errvved L s L m e e a s m R e e DDrreaghttss R © © ll RRiigh AAll Wall Profile Glass Profile 1” m ax d e e n iine errvved L s L m e e a s m R e e DDrreaghttss R © © ll RRiigh AAll ® ® ST4.
©2020 DreamLine® All Rights Reserved Tools Tape Measure Level Phillips Screwdriver Pencil d e e n v i r L e s m e a R e r s D ght © Ri l l A Silicone ® Drill Bit Ø5/16" (8mm) Drill Bit Drill Bit Ø3/16" Ø1/8" (4.
©2020 DreamLine® All Rights Reserved Detailed Diagram of Shower Door Components 03 d e e n v i r L e s m 17a e a R e r s D ght © Ri l l A ® inside 07 02 13 09 11 14 18 inside 08 05 04 12 06 03 17b inside 16 d e e n v i r L e s m e a R e r s D ght © Ri All inside ® 10 inside 01 Left-hand door installation shown INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 6
©2020 DreamLine® All Rights Reserved Parts List 01 02 03 d e e n v i r L e x2 s x2 m e a R e r s D ght © Ri05 06 l l A ® Glass Profile 04 Door Glass Wall Profile x1 10 ST4.0x25mm Pan Head screw Inline Panel Glass x1 08 07 Anti-water Strips 1 Short, 2 Long Guide Rail (Top and Bottom) Handle x8 ® Push-in Glazing Vinyl ST4.0x10mm Pan head screw INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 x1 09 d e e x1 n v i r L e s m e a R e r s D 11ght 12 © Ri All x3 x2 ST4.
13 ©2020 DreamLine® All Rights Reserved Parts List 15 14 d e e n v i r L e x4 s x8 m e a R e r s D ght © Ri17a 17b 17a l l A ® Decorative Cover (with washer) 16 Glass Clip Wall Anchor x2 Wheel Assembly (Top) x2 Vinyl Insert Wheel Assembly (Bottom) x1 x2 18 Towel Bar d e e n v i r L e s m e a R e r s D ght © Ri All x1 INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 ® 8
©2020 DreamLine® All Rights Reserved Installation Steps 1 Top *at model height d e e n v i r L e s m e a R e r s D ght © Ri l l A ® ________” Middle ________” Bottom ________” Fig 1 TIP NOTE W d e e n v i r L e s m e a R e r s D ght © Ri All ®determine Use the smallest measurement from Fig 1 to the finished cut length of the Guide Rails (#03). The Top and Bottom Guide Rails (#03) are shorter than the model size by design.
- = Finished Opening (W) MODEL SIZE *from Table A Cut-off Length (C) *from Door End only Panel Side d e e n v i r L e s m e a R e s Dr ghtCenter © Ri All ® Cut the Top and Bottom Guide Rails (#03) from the Door End only, (which is the end farthest from the Glass Clip hole) and cut each rail to the same length (D) from the same end.
©2020 DreamLine® All Rights Reserved 3 1 2 3-1/8” to the center of the hole r doo end d e e n v i r L e s m e a R e Dr ghts © Ri Ø1/8” l l A ® r doo end 3 door end d e e n v i r L e s m e a R e Dr ghts © Ri All ® Fig 3 /8” 3-1 nter e ce to th e hole of th Top Rail Door End Parts Needed Bottom Rail /8” 3-1he center Tools Needed 03 to t e hole of th x2 INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 11
©2020 DreamLine® All Rights Reserved 4 top d e e n v i r L e s m e a R e Dr ghts © Ri All ® ® Fig 4 d ve e r n i L e s m e a R e Dr ghts © Ri All bottom TIP For ease of installation: Add liquid soap, wax, or lubricant to the screws prior to attaching the Glass Profiles (#01) to the Guide Rails (#03). Use a low setting on the screw gun to prevent stripping the screws.
©2020 DreamLine® All Rights Reserved 5 d e e n v i r L e s m e a R e Dr ghts © Ri All ® Fig 5 d e e n v i r L e s m 2 e a R e Dr ghts © Ri All ® 1 Holes in both profiles must line up inside inside Parts Needed 02 NOTE The holes in the Wall Profiles (#02) are off-center, and must line up with the corresponding holes in the Glass Profiles (#01).
NOTE ©2020 DreamLine® All Rights Reserved 6 At this step, decide on the handing of the door and panel prior to placing the assembly into the opening to mark the location of the holes for drilling. Flip the assembly so that the Inline Panel Glass (#06) will be installed on the desired side of the opening. d e e n v i r L e s m e a R e Dr ghts © Ri All ® 1 ±0.
©2020 DreamLine® All Rights Reserved 7 1 d e e n v i r L e s m e a R e Dr ghts © Ri All ® 2 Ø3/16” Drill Bit 3* *see NOTE d e e n v iFig 7 er L s m e a R e r s D ght © Ri All ® NOTE If a stud is present behind the wall, drill a hole using a Ø3/16” drill bit up to the stud, drill an Ø1/8“ pilot hole into the stud and do not use wall anchors. If no stud is present, drill the hole using a Ø5/16” drill bit and insert Wall Anchors (#14) as shown in Fig 7.3.
! ©2020 DreamLine® All Rights Reserved 8 Before securing the frame assembly, bring the Door Glass (#04) into the shower area and lean it safely against the wall, using padding to protect the glass, walls, and base. Make sure the handle holes on the Door Glass (#04) are on the correct side for installation. The Wheel Assemblies (#17a/17b) can be attached prior to setting the glass into the shower.
©2020 DreamLine® All Rights Reserved 9 1 wall profiles 2 3 d e e n v i r L e s m e a R e Dr ghts bottom © Ri rail All ® ne silicone 4 silico 5 ST4.0×55 6 ST4.0×55 wall wall Overhead View Fig 9 TIP d e e n v i r L e s m e a R e Dr ghts © Ri All Extender Driver Bit recommended for the installation of these screws. ® Parts Needed NOTE The screwheads on the ST4.
©2020 DreamLine® All Rights Reserved 10 1 2 d e e n v i rinside L e s m e a R e Dr ghts © i inside R All ® Fig 10a NOTE For models with Frosted glass, install the textured (Frosted) surface facing towards the outside of the shower. Use caution when installing the Inline Panel Glass (#05) into the frame to prevent damage to the edges of the glass.
©2020 DreamLine® All Rights Reserved 11 d e e n v i r L e s m e a R e r s D ght © Ri l l A ® inside d e e in erv L s m e a Fig 11 R e r s D ght © Ri All ® Right-hand panel installation shown Parts Needed ! To prevent scratching or damaging the glass and aluminum, DO NOT use a screwdriver or other metal tool to install the Push-in Glazing Vinyl (#08). Use a plastic putty knife or similar if necessary.
©2020 DreamLine® All Rights Reserved 12 d e e n v i r L e s m e a R doo e r r gla s t sD s h © Rig inside l l A ® inside d e e n v i r L e s m e a R e r s D ght © Ri All ® Fig 12 *Left-hand door installation shown NOTE Top Wheels The lock nut on the Top Roller Assembly (#17a) and the push-button on the Bottom Roller Assembly (#17b) should both be installed pointing up. DO NOT overtighten the Roller Assemblies (#17a/17b).
©2020 DreamLine® All Rights Reserved 13 1 2 inside d e e n v i r L e s m e a R e r s D ght © Ri l l bottom A ® align and install 3 inside lift up 4 adjust* align and install d e e n v i r L e s m e a R e r s D ght © Ri All top ® Fig 13 NOTE *If necessary: Adjust the Top Roller Assemblies (#17a) for smoother operation.
©2020 DreamLine® All Rights Reserved Handle and Vinyl Installation 14 d e e n v i r L e s m e a R e Dr ghts © Ri All ® inside door door glass Inline Panel Glass panel door glass outside Fig 14 d e e n v i r L e s m e a R e Dr ghts © Ri All NOTE ® The longer Vertical Vinyl Seals (#07) attach to the edges of the Door Glass (#04); the shorter Vertical Vinyl Seal (#07) attaches to the edge of the Inline Panel Glass (#05).
DO NOT drill the profiles throughout, ONLY through the first layer of the Wall Profile (#02) and Glass Profile (#01). ! 1 3/4” ll wa ©2020 DreamLine® All Rights Reserved 15 2 d e e n v i r L e s wall m e a R e r s D ght © Ri l l A ® Ø1/8” inside inside 3 4 ll wa ll wa inside inside d e e n iFig 15 erv L s m e a R e r s D ght © Ri All ® NOTE Make sure that the bottom rail is tight to the threshold before screwing the wall profiles and glass profiles together NOTE The ST4.
©2020 DreamLine® All Rights Reserved 16 NOTE The surfaces need to be clean and free of debris before applying silicone. d e e n v i r L e s24 m e a R e r s D ght Hours © Ri l l A ® d e e n v i r L e s m e a R e r s D ght © Ri All ® Fig 16 ! Tools Needed Allow 24 hours for the silicone caulk to cure before using shower.
©2020 DreamLine® All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
Problem/Symptom Missing Parts Suggested Solution •Check all shipping/packaging material for missing parts/components. •If not found, contact DreamLine Customer Support [1-855-8312126] to order factory part replacement. d e e n v i r L e s m e a R e r s D ght © Ri l l A ® Page(s) ―― Leakage: underneath Bottom Guide Rail (#03) •Make certain that the bottom rail is tight to the threshold and that silicone is creating a seal along the entire length of the bottom rail.
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 48x72 Clear Glass ITEM # FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCRIPTION QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1134 / 04004011-1134 / 04006011-1134 Top or Bottom Guide Rail 2 pcs 04 010021014 Door Glass 1 pc 05 0100
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 48x72 Frosted Glass ITEM # FACTORY PARTS INFORMATION ITEM DESCRIPTION FACTORY PART NUMBER QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1134 / 04004011-1134 / 04006011-1134 Top or Bottom Guide Rail 2 pcs 04 010021016 Door Glass 1 pc 05 010
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 54x72 Clear Glass ITEM # FACTORY PARTS INFORMATION ITEM DESCRIPTION FACTORY PART NUMBER QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1283 / 04004011-1283 / 04006011-1283 Top or Bottom Guide Rail 2 pcs 04 010022011 Door Glass 1 pc 05 01002
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 54x72 Frosted Glass ITEM # FACTORY PARTS INFORMATION ITEM DESCRIPTION FACTORY PART NUMBER QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1283 / 04004011-1283 / 04006011-1283 Top or Bottom Guide Rail 2 pcs 04 010022013 Door Glass 1 pc 05 010
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 60x72 Clear Glass ITEM # FACTORY PARTS INFORMATION ITEM DESCRIPTION FACTORY PART NUMBER QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1437 / 04004011-1437 / 04006011-1437 Top or Bottom Guide Rail 2 pcs 04 010021010 Door Glass 1 pc 05 01002
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 60x72 Frosted Glass ITEM # FACTORY PARTS INFORMATION ITEM DESCRIPTION FACTORY PART NUMBER QTY 01 04002011-1830 / 04002041-1830 / 04002061-1830 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1830 / 04183041-1830 / 04183061-1830 Left or Right Wall Profile 2 pcs 03 04001011-1437 / 04004011-1437 / 04006011-1437 Top or Bottom Guide Rail 2 pcs 04 010021011 Door Glass 1 pc 05 010
INFINITY-Z Shower and Tub Door Manual Ver 5 Rev 2 012020 Product Parts Information INFINITY-Z 60x58 Clear Glass ITEM # FACTORY PARTS INFORMATION FACTORY PART NUMBER ITEM DESCRIPTION QTY 01 04002011-1474 / 04002041-1474 / 04002061-1474 Left or Right Glass Profile for 6mm (1/4in) Glass 2 pcs 02 04183011-1474 / 04183041-1474 Left or Right Wall Profile 2 pcs 03 04001011-1437 / 04004011-1437 / 04006011-1437 Top or Bottom Guide Rail 2 pcs 04 010021007 Door Glass 1 pc 05 010022001 Inline Pa
d e e n v i r L e s m e a R e r s D ght © Ri All ® d e e n v i r L e s m e a R e r s D ght © Ri All ® TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.