Charisma Tub Door & Backwall TUB DOOR & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
QWALL TUB TUB ACRYLIC BACK WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please carefully read the instructions before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package, by marking all the components on the “Detailed Diagram of Tub Back Wall Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date.
Detailed Diagram of Tub Back Wall Components 4 2 1 5 3 6 7 8 9 10 Packing List 01 Side panel 2pcs 06 Wall anchor 21pcs 02 Back panel 2pcs 07 Countersunk screw ST4.2×30 21pcs 03 Decorative edge molding 2pcs 08 Decorative cover 15pcs 04 Corner cover 2pcs 09 Glass shelf 2pcs 05 Wall cover 1pc 10 Shelf bracket 6pcs NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference.
Back Panel Installation Instruction 1. Measure the distance of the back wall of the tub (corner to corner) The distance is “W” W See Fig. 1 for details. Fig. 1 W/2 2. Divide the W measurement by 2 (W/2). Place a mark on the back wall and draw a vertical line from top to bottom. W/2 See Fig. 2 for details. Fig. 2 Rev 1.
3. Measure the side walls from the corner to the front point where the Side panel (01) is going to end. This distance is “D”. D See Fig. 3 for details. D Fig. 3 D - 1” 1” Trim line 4. Verify on which side of your tub wall the fixtures will be installed. Place a mark on the side wall (NB: not the side panel!) with a distance of 1” (one inch) from the corner and draw a vertical line from top to bottom.
Fig. 5 5. Attach the Center cover (05) vertically at the center point along the line and mark the drilling holes through the predrilled holes on the Center cover. Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (06). 1 See Fig. 6 and Fig. 7 for details. 2 3 Ø5/16” 4 Fig. 6 Rev 1.
Fig. 7 6. Attach the Corner cover (04) to the corner of the wall and mark the drilling holes through the predrilled holes on the Corner cover. Drill the holes using Ø5/16” drill bit and insert the Wall Anchors (06). See Fig. 8 and Fig. 9 for details 1 3 Ø5/16” 2 4 Fig. 8 Rev 1.
Fig. 9 7. Determine the position of both Back panels (02). NOTE: a) Narrow side of the Back panel cannot be trimmed and should face the center of the Back wall. b) Wide side of the Back panel can be trimmed to the size of the wall and should face the corner. W/2-1” W/2-1” b a Place a mark on the wide side of the Back panel with a distance of (W/2 – 1”) from the center edge of the Back panel to the wide side of the Back panel and draw a straight line from top to bottom. b See Fig. 10 for details.
8. Place the Back panel (02) on a flat piece of plywood or a particle board. Cut the side end of the Back panel by making a few deep scratches with a sharp industrial knife using a T-Square tool or a handheld jig saw. See Fig. 11 and Fig. 12 for details. 1 2 Fig. 11 W/2-1” W/2-1” a Fig. 12 Rev 1.
1 9. Mount the Center cover (05) to the center of the back wall using the Countersunk screws ST4.2×30 (07). Do not tighten the screws. Leave the Center cover loose on the wall. See Fig. 13 for details. 2 Fig. 13 10. Apply the sealant to the back of the left Back panel (02). See Fig. 14 for details. Fig. 14 Rev 1.
1 11. Slide the right edge of the left Back panel (02) all the way behind the Center cover (05) and push the Back panel against the wall. You can adjust the position of the Back panel before the sealant sets. Apply equal pressure to the whole surface of the Back panel from top to bottom. Fasten the Corner cover (04) to the left corner of the back wall using the Countersunk screws ST4.2×30 (07). Do not tighten the screws. 2 See Fig. 15 for details. 3 Fig. 15 4 12.
. Align both Back panels at the top and tighten the screws on the Center cover (05) to secure this assembly in place. 1 See Fig. 17 and Fig. 18 for details. 2 Fig. 17 Fig. 18 Rev 1.
. Determine the position of both Side panels (01). D -1” D -1” NOTE: a) Narrow side of the Side panel cannot be trimmed and should face the corner of the side wall. b) Wide side of the Side panel can be trimmed to size of your measurements and should face the front of the tub. Place a mark on the wide side of the Side panel with a distance of D – 1” from the corner side of the Side panel to the front edge and draw a straight line from top to bottom. See Fig. 19 for details. Fig. 19 15.
D -1” D -1” Fig. 21 16. Place the marks on the Side panel (01) which is going to the side wall with the fixtures according to the taken measurements in Fig. 4. Drill the holes in the Side panel. Mind using the proper diameter saw bit or a handheld jig saw. See Fig. 22 and Fig. 23 for details. Fig. 22 Rev 1.
Fig. 23 17. Apply the sealant to the back surface of the Side panel (01). Apply the sealant around the drilled holes and to the whole back side of the Side panel. See Fig. 24 for details. Fig. 24 Rev 1.
18. Slide the edge of the Side panel (01) all the way behind the Corner cover (04) and push the Side panel against the wall. Align the top of the Side panel with the Back panel before the sealant sets. Apply equal pressure to the whole surface of the Side panel from top to bottom. Peel off the adhesive tape on the back side of the Decorative edge molding (03) and attach it to the front edge of the Side panel. Apply pressure to the Decorative edge molding from top to bottom. See Fig. 25 for details.
19. Apply the sealant to the back surface of the Side panel (01) for another side wall installation. See Fig. 27 for details. Fig. 27 20. Repeat Step 18 to install the second Side panel. 1 3 2 4 See Fig. 28 and Fig. 29 for details. Fig. 28 Rev 1.
Fig. 29 1 21. Fasten tight the Corner covers (04) and the Center cover (05) to secure the Side panels (01) and the Back panels (02) in place. See Fig. 28 for details. 2 Fig. 28 Rev 1.
22. Use decorative plugs to cover the screw holes in the Corner covers (04) and the Center cover (05). 1 See Fig. 29 for details. 2 Fig. 29 23. Apply caulk along the top edge of the panels and along the connection of the bottom edges of the panels with the tub. See Fig. 30 for details. ATTENTION: Installation of QWALL-Tub is complete. If you want to install Glass shelves (09) to your Tub Wall, follow to the next step. Fig. 30 Rev 1.
Tub Glass Shelves Installation Instruction 24. Find the desirable height for the Glass shelves (09) and mark the locations on the wall. NOTE: The Glass shelves can be installed either two in one corner, or one in each. G See Fig. 31 for details. H Fig. 31 25. Mark the location for the Shelf brackets (10) according to the measurements in Fig. 32.1. Drill the holes using Ø5/16” drill bit and insert the Wall anchors (06). 3½” 3½” 3½” See Fig. 32 for details. 1 Ø 5/16” 2 3 Fig. 32 Rev 1.
1 10. Mount the Glass brackets (10) to the wall using the Countersunk screws ST4.2×30. NOTE: padded set screw of the Glass bracket should be facing down. Slide the upper Glass shelf (09) into the Glass brackets and tighten the set screws at the bottom of the brackets. Then slide the bottom Glass shelf in place. Tighten the set screws as well. 2 See Fig. 33 and Fig. 34 for details. 3 Fig. 33 Fig. 34 Rev 1.
Product maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. Acrylic cleaning procedure: Acrylic should be cleaned with warm water and a clean, nonabrasive cloth. If desired, a mild, nonabrasive detergent may also be used. Use only light pressure when cleaning.
Warranty 2011 This is Bath Authority LLC’s (“DreamLine”) exclusive written warranty effective April 1, 2011 This warranty extends only to the original owner/end-user for household use only and is not transferable to a subsequent owner. This warranty applies only to DreamLine™ products purchased from an authorized dealer and installed in United States or Canada. Proof of purchase (original sales receipt) must be provided with all warranty claims.
TEL: 866-731-8378 – 215-957-1411 FAX: 866-227-9245 – 215-893-1780 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Tub Back Wall please visit www.BathAuthority.com Rev 1.
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a soft cloth.
Preparation 1. PRIOR TO INSTALLATION, EXAMINE ALL BOXES AND PACKAGES FOR SHIPPING DAMAGE AND COMPARE THE PIECE COUNT WITH YOUR PACKING SLIP. AFTER OPENING ALL BOXES AND PACKAGES READ THIS INTRODUCTION CAREFULLY. CHECK THAT ALL OF THE NEEDED PARTS ARE INCLUDED IN THE PACKAGE BY CHECKING OFF THE COMPONENTS ON THE “DETAILED DIAGRAM OF SHOWER DOOR COMPONENTS”.
Tools Level Silicone Tape Pencil Measure Power Drill Drill bit 5/16” (8mm) Phillips Screwdriver Drill bit 3/16" (5mm) Drill bit 9/64" (3.5mm) Hammer Miter saw or Hacksaw Metal File Painter’s Tape Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Top Middle Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts.
Detailed Diagram of shower door components 5 1 6 3 8 4 9 10 11 12 13 15 The glass surface with the ClearMax™ label must be installed facing the inside of the shower 16 2 # Item Parts List Qty # 9 Item Qty Decorative cover for Guide block 6PCS 10 Roller assembly 4PCS 11 Guide rail bracket 2PCS 2PCS 12 Guide Block (left / right / middle) 1set 4PCS 13 4PCS Round head screwST4.2×16 6PCS Round head screwST4.
Installation steps 1. Measure the finished opening width at the top, middle and bottom. This distance is marked as “W”. See Fig 1 for details W Fig 1 GUIDE RAIL (#01) W = FINISHED OPENING -1/16” 2. The Guide Rail (#01) and the Bottom Rail (#02) have been precut for your model size width of 48” or 60”. If your finished opening width is less than 48” or 60”, you will need to cut the Guide Rail (01) and the Bottom Rail (02) to “W” (W = finished opening -1/16”).
BOTTOM RAIL (#01) W = FINISHED OPENING -1/16” Divide the amount to be cut off by 2... W ...then cut off equal amounts from each end For Example, if the rail measures 60” out of the box and your finished opening = 57“, then you will need to cut 1-1/2” from each end. Place the Bottom Rail (#02) in the desired position and parallel to the front edge of the Shower base or the Tub deck. (60“ minus 57” = 3“, divided by 2 = 1-1/2”).
4. Apply silicone to the underside of the bottom rail, then position it in place on the threshold. See Fig 5 for details TIP: Use Painter’s tape to hold the bottom rail in place while the silicone cures. Fig 5 5. Draw a plumb line from the front outside edge of the Bottom Rail (#02) up from the threshold/tub deck surface to locate the left Guide Rail Bracket (#11).
HEIGHT OF THE GUIDE RAIL BRACKET FOR 76” SHOWER DOOR: MODEL # SHDR-1348760 & SHDR-1360760 6. Place the Guide Rail Bracket (#11) at a height of 74” from the base. 74” Align the front bottom corner of the Guide Rail Bracket (#11) with the outside of the Bottom Rail (#02) to mark the wall for drilling. Be sure to keep the Guide Rail Bracket (#11) level. See Fig 7 for details 74” Fig 7 HEIGHT OF THE GUIDE RAIL BRACKET FOR 58” TUB DOOR: MODEL # SHDR-1360580 7.
8. Mark the drill holes on the wall using the Guide rail bracket (#11). Drill the holes using a Ø5/16” drill bit. Insert the Wall anchors (#05) and secure the Guide rail bracket (#11) to the wall with the Round head screw ST4.2×40 (#08). See Fig 9 for details 1 2 3 Ø 5/16" 4 5 Fig 9 9. Place the Guide Rail (#01) onto the installed Guide Rail bracket (#11). Use a level to confirm the installation height of the second bracket before drilling on the opposite wall.
10. Install the Guide Rail (#01) over the top of the Guide Rail brackets (#11) and lock them together. Mark the drill holes in the underside of the Guide Rail (#01) through the holes in the bottom of the bracket. Remove the Guide Rail (#01) and drill the holes using an Ø1/8” drill bit. Before attaching the Guide Rail (#01) to the Guide Rail brackets (#11): Slide two Roller assemblies (#10) into each channel of the Guide Rail (#01) with the finished surface of the disks facing out. (Fig 11.6, 11.
12. Secure the Door Glass (#03) onto the Roller assemblies (#10) and fasten them with the provided bolts. See Fig 13 for details TIP: BE SURE TO COVER THE DRAIN TO PREVENT LOOSING ANY SCREWS. NOTE: ROTATING THE GLASS HOLDER OUTER DISKS: THE DISK BOLT IS POSITIONED OFF-CENTER BY 1/8” TO PROVIDE FOR SOME MINOR ADJUSTMENTS TO THE DOOR GLASS TO ACHIEVE A BETTER SEAL WITH THE WALL. YOU WILL NEED AN ASSISTANT TO SUPPORT THE WEIGHT OF THE GLASS WHILE YOU LOOSEN THE BOLT, ROTATE THE DISK AND RE-TIGHTEN THE BOLT.
14. As viewed from the outside: Slide the Door Glass (#03) to the right side and secure the Left Guide block (#12) to the left end of the Bottom Rail (#02). Drill Ø1/8" holes into the Bottom Rail (#02) through holes in the Guide block (#12) and fasten the Guide Block (#12) with the Round head screw ST4.2×16 (#06). Install the Middle Guide block (#12) into the pre-drilled holes in the Bottom Rail (#02) using the Round head screws ST4.2×16 (#06).
16. Apply a good quality mildew-resistant silicone along the connection of the Guide Rail (#01) and the shower base or tub deck. Allow 24 hours for the silicone to fully cure before using the shower.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosure please visit DreamLine.
