©2018 DreamLine. All Rights Reserved UNIDOOR/UNIDOOR-LS/UNIDOOR LUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved Style “A” (single door installation shown) with Half-Frosted Glass: NOTE: This model features the Half-Frosted glass option. The textured surface on the door glass should be installed to face outside of the shower. The door glass can be flipped for left or right-hand installation.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Models with Glass-to-Glass Hinge panels: For Glass-to-Glass Hinge Door models: Use the installation manual that is packaged with the Hinge panel glass first.
©2018 DreamLine. All Rights Reserved STYLE A UNIDOOR Single shower door 23”- 30” Refer to detailed diagram on page 12 of this manual to begin the installation.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package(s) by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Single Shower Door Assembly and Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR, UNIDOOR-LS, UNIDOOR LUX and UNIDOOR PLUS models. Before you begin the installation, please check your finished opening size. Specific size information can be found on DreamLine.
©2018 DreamLine. All Rights Reserved 2. The Door Glass (01) ships with four 5/8” shims attached to the top (2pcs) and bottom (2pcs). Determine the swing of your door and only remove the shims from the top of the door glass, leaving the bottom shims in place. Set the Door Glass (01) onto the threshold at the desired location and check for level.
©2018 DreamLine. All Rights Reserved 1 TIP: The PVC hinge spacer can also be used as a template to assist with marking the hinge mounting holes. 2 *Only use the PVC hinge spacer to correct for minor out-of-plumb wall conditions. 3 Fig. 4 ATTENTION: As viewed from inside the shower, the hinge plate is very close to the drilled holes in the wall and might get scratched while installing the long screws. Be careful not to scratch the hinge surfaces during installation. (OPTIONAL) 5.
©2018 DreamLine. All Rights Reserved Setting the Adjustable Hinges The Adjustable hinges are pre-set to overclose to 85º and are adjustable up to 90º after the door is installed. Once the door glass is installed, simply loosen the Allen set screws and position the door to the desired closed position. While holding the door in the new closed position, retighten the Allen screws and your door will now self-center to the chosen closed position. 5a.
©2018 DreamLine. All Rights Reserved 5b. The hinges are factory set to 85 degrees. You can change this angle by using the adjustment screws on the hinge plate. (Fig 5b) outside inside Fig 5b 5c. Use the supplied Allen Key to loosen the adjustment screws on the inside hinge plate, adjust the door to the desired angle (90 degrees for example) then retighten the adjustment screws (Fig 5c). Be sure that you create a tight seal with the supplied strike vinyl when the door is in the closed position.
©2018 DreamLine. All Rights Reserved 6. Mount the Handle (02) to the Door Glass (01). (Fig 6) Fig. 6 7. Measure the bottom of the Door Glass (01) from end to end to determine the actual width of the door. Cut the Bottom anti-water strip (07) to the size of your measurement and notch approximately 3/8” off the inner side of the Bottom anti-water strip as shown. Press the Bottom Anti-water strip (07) tightly onto the bottom edge of the Door Glass (01).
©2018 DreamLine. All Rights Reserved 1 2 7/8" Into the hinge Into the hinge 3 4 7/8" 7/8" 8. Take three measurements: from the top edge of the Door Glass (01) to the upper body of the top Hinge (05) (+) 7/8” from the lower body of the upper Hinge to the upper body of the bottom Hinge (+) 1-3/4” from the lower body of the bottom Hinge to top of the installed Bottom anti-water strip (07) (+) 1-7/8” Cut the Side strip (06) according to the measurements.
©2018 DreamLine. All Rights Reserved Fig. 10 If the model includes additional panel glass, refer to the manual that is packaged with the panel glass to continue with the installation.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2018 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
