UNIDOOR / UNIDOOR-LS Style B SHOWER DOOR AND INLINE PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved UNIDOOR/UNIDOOR-LS/UNIDOOR LUX/UNIDOOR PLUS SINGLE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
©2018 DreamLine. All Rights Reserved Style “A” (single door installation shown) with Half-Frosted Glass: NOTE: This model features the Half-Frosted glass option. The textured surface on the door glass should be installed to face outside of the shower. The door glass can be flipped for left or right-hand installation.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Models with Glass-to-Glass Hinge panels: For Glass-to-Glass Hinge Door models: Use the installation manual that is packaged with the Hinge panel glass first.
©2018 DreamLine. All Rights Reserved STYLE A UNIDOOR Single shower door 23”- 30” Refer to detailed diagram on page 12 of this manual to begin the installation.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package(s) by checking off the components on the “Detailed Diagram of Shower Door Components”.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine.
©2018 DreamLine. All Rights Reserved Single Shower Door Assembly and Installation NOTE: The following shower door installation instructions should be used as a general guide and prerequisite to the installation of the UNIDOOR, UNIDOOR-LS, UNIDOOR LUX and UNIDOOR PLUS models. Before you begin the installation, please check your finished opening size. Specific size information can be found on DreamLine.
©2018 DreamLine. All Rights Reserved 2. The Door Glass (01) ships with four 5/8” shims attached to the top (2pcs) and bottom (2pcs). Determine the swing of your door and only remove the shims from the top of the door glass, leaving the bottom shims in place. Set the Door Glass (01) onto the threshold at the desired location and check for level.
©2018 DreamLine. All Rights Reserved 1 TIP: The PVC hinge spacer can also be used as a template to assist with marking the hinge mounting holes. 2 *Only use the PVC hinge spacer to correct for minor out-of-plumb wall conditions. 3 Fig. 4 ATTENTION: As viewed from inside the shower, the hinge plate is very close to the drilled holes in the wall and might get scratched while installing the long screws. Be careful not to scratch the hinge surfaces during installation. (OPTIONAL) 5.
©2018 DreamLine. All Rights Reserved Setting the Adjustable Hinges The Adjustable hinges are pre-set to overclose to 85º and are adjustable up to 90º after the door is installed. Once the door glass is installed, simply loosen the Allen set screws and position the door to the desired closed position. While holding the door in the new closed position, retighten the Allen screws and your door will now self-center to the chosen closed position. 5a.
©2018 DreamLine. All Rights Reserved 5b. The hinges are factory set to 85 degrees. You can change this angle by using the adjustment screws on the hinge plate. (Fig 5b) outside inside Fig 5b 5c. Use the supplied Allen Key to loosen the adjustment screws on the inside hinge plate, adjust the door to the desired angle (90 degrees for example) then retighten the adjustment screws (Fig 5c). Be sure that you create a tight seal with the supplied strike vinyl when the door is in the closed position.
©2018 DreamLine. All Rights Reserved 6. Mount the Handle (02) to the Door Glass (01). (Fig 6) Fig. 6 7. Measure the bottom of the Door Glass (01) from end to end to determine the actual width of the door. Cut the Bottom anti-water strip (07) to the size of your measurement and notch approximately 3/8” off the inner side of the Bottom anti-water strip as shown. Press the Bottom Anti-water strip (07) tightly onto the bottom edge of the Door Glass (01).
©2018 DreamLine. All Rights Reserved 1 2 7/8" Into the hinge Into the hinge 3 4 7/8" 7/8" 8. Take three measurements: from the top edge of the Door Glass (01) to the upper body of the top Hinge (05) (+) 7/8” from the lower body of the upper Hinge to the upper body of the bottom Hinge (+) 1-3/4” from the lower body of the bottom Hinge to top of the installed Bottom anti-water strip (07) (+) 1-7/8” Cut the Side strip (06) according to the measurements.
©2018 DreamLine. All Rights Reserved Fig. 10 If the model includes additional panel glass, refer to the manual that is packaged with the panel glass to continue with the installation.
©2018 DreamLine. All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
©2018 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
INLINE PANEL - STYLE B INLINE PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Model #s UNIDOOR - Style B w/ 6” inline UNIDOOR - Style B inline w/L-Bar™ MODEL #s MODEL #s SHDR-20297210-## SHDR-20307210-## SHDR-20317210-## SHDR-20327210-## SHDR-20337210-## SHDR-20347210-## SHDR-20357210-## SHDR-20367210-## UNIDOOR - Style B inline w/ Support Bar MODEL #s SHDR-20417210C-## SHDR-20427210C-## SHDR-20437210-## SHDR-20447210-## SHDR-20457210-## SHDR-20467210-## SHDR-20477210-## SHDR-20487210-## SHDR-20477210C-## SHDR-20487210C-## SHDR-20497210-## SHDR-20507210-## SHDR-20517210-## SHDR
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the buildup of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. ©2018 DreamLine. All Rights Reserved For best results, squeegee the glass after each use and dry with a soft cloth.
Table of Contents Page # Preparation Tools 2 Detailed Diagram of Shower Panel Components Parts List 4 5 Adjustable Wall Profile System 6 Installation Steps 7-16 Vinyl Seals 9 Support Bar Installation 13 L-Bar Assembly 14 Product maintenance 17 Left-side inline panel installation ! 3 Right-side inline panel installation NOTE: This model is reversible for right or left-side panel installation. The right-side panel installation is shown as an example throughout this manual.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the “Detailed Diagram of Shower Panel Components”.
Tools Level Tape Measure Power Drill Phillips Screwdriver Knife Professional-grade Glass suction cup Pencil Silicone Drill bit (Ø5/16") (8mm) Drill bit (Ø1/8") (3mm) Soft Head Hammer Mallet Top Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered. Threshold must be level shower/tub drain with tape to prevent losing screws or small parts.
Detailed Diagram of Shower Panel components Diagram A 12* 11 10 Diagram B 11 9 10 13 13 14 14 15 15 16 16 17 17 18 18 19 19 9 12a Right L-Bar™ (installation shown) 12b Left L-Bar™ 23 Right side panel installation shown (using Right L-Bar™) ©2018 DreamLine.
Parts List Diagram A PART# DESCRIPTION QTY PART# DESCRIPTION QTY 09 Wall profile 1pc 15 Truss head screw ST4.2x40 4pcs 10 Glass profile 1pc 16 Pan head screw ST4.2x35 1pc 11 Panel glass 1pc 17 Decorative screw cover and washer 4pcs 12* Support bar * 1pc 18 Bottom bracket 1pc 13 Wall Anchor 4pcs 19 Anti-Water strip (inline) 1pc 14 Pan head screw ST4.2x10 3pcs 23 Countersunk screw ST4.
Adjustable Wall Profile System Glass Profile Wall Profile 1” m The Glass Profiles can be adjusted within the Wall Profiles for overall width or to correct for out-of-plumb conditions within the model size. Screw them together after making final adjustments. her 3 Ø1/8" was w scre 2 dec ora tive cap 1 ©2018 DreamLine.
Installation steps NOTE: The UNIDOOR or ELEGANCE shower door ! needs to be installed prior to proceeding with the following Panel Glass installation. Please see the Single Shower Door installation manual included in the door packaging for complete shower door installation instructions. Before beginning the installation, recheck the finished opening size. Specific model size information can be found on DreamLine.com.
2. Apply clear silicone into the entire length of the channel of the Glass Profile (#10) and attach it to the edge of the Panel Glass (#11). Make sure the Glass Profile (#10) is flush with the top and bottom of the Panel Glass (#11). Insert the Panel Glass (#11) with the attached Glass Profile (#10) into the Wall Profile (#09). (Fig 2) ! ATTENTION: Please note that the bottom hole in the corner of the Panel Glass must be opposite from the Glass Profile.
3. Press the Anti-Water Strip (inline) (#19) onto the vertical edge of the Panel Glass (#11). (This will protect the edge of the panel glass and allow for proper spacing with the door glass). Attach the Bottom Bracket (#18) through the bottom hole of the Panel Glass (#11). (Fig 3) 1 inside 2 3 inside 4 inside inside Fig 3 4. Carefully position the assembled panel onto the threshold and against the wall. Push the Wall Profile (#09) tight to the wall while holding the panel tight to the threshold.
5. Close the Door and align the Panel Glass (#11) with the Door. Use the reference mark on the threshold (from Step #1 ) to confirm that the Door is perpendicular to the wall. If necessary, adjust the position of the Panel Glass (#11) so that the Anti-Water Strip (inline) (#19) makes contact with the Door Glass from top to bottom and creates a seal. ◾Mark the wall along the inner edge of the Wall Profile (#09). ◾Mark the drilling hole onto the threshold through the hole in the Bottom Bracket (#18).
! Double check the alignment and spacing of the panel glass with the door glass before drilling into the threshold for the bottom bracket. 7. Drill a hole for the Bottom Bracket (#18) into the threshold at the mark that was made in Step #5. ** Use an Ø1/8” drill bit for installation into an acrylic base OR use a Ø5/16” drill bit and an anchor for installation into a tile threshold. Use the Pan Head Screw ST4.
8. Recheck the alignment and spacing of the Door Glass and Panel Glass (#11) and test the operation of the Door. After final adjustments of the Panel Glass (#11) drill holes into the Glass Profile (#10) through the predrilled holes in the Wall Profile (#09) using an Ø1/8” drill bit. Use the Pan Head Screws ST4.2×10 (#14) and Washers (#17) to attach the Wall Profile (#09) to the Glass Profile (#10). Cover the exposed screw heads with Decorative Screw Cover (#17).
Support Bar Assembly and Installation 10. Attach the Support Bar (#12) to the Panel Glass as shown. ◾ Adjust the Support Bar (#12) to a proper position on the glass and the wall (ideally at a 45° angle) and level it. ◾ Outline the Wall Bracket’s position on the wall Fig 10.2. ◾ Remove the Wall Bracket from the Support Bar (#12). ◾ Place the Wall Bracket against its outlined position on the wall and mark the hole for drilling.
L-Bar™ Parts List Assembly (Right L-Bar™ shown) Right L-Bar™ installation shown as an example 4.9 4.4 4.3 4.5 4.2 4.6 4.1 4.7 4.8 Unidoor-LS -Style B DESCRIPTION QTY PART# DESCRIPTION QTY 4.1 PVC spacer 2pcs 4.6 Wall Plate 1pc 4.2 M5 rubber tip set screw 2pcs 4.7 Truss Head Screw ST4.2x40 2pcs 4.3 L-Bar™(Right-hand shown) 1pc 4.8 Flat Head Screw M5x14 2pcs 4.4 Decorative cover 1set 4.9 Wall Plate adjustment set screw 2pcs 4.
11. Position the L-Bar™ assembly (#4.3) onto the Panel Glass as shown (Fig 11.1). Be sure the gaskets are in place to protect the glass. Make it level and mark the position on the wall. Remove the Decorative Cover (#4.4) and Wall Plate (#4.6) from the L-Bar™. Position the Wall Plate (#4.6) on the marks on the wall and adjust for level. Mark the holes for drilling through the wider, untapped holes (Fig 11.3). Drill two Ø5/16”(8mm) holes and insert the Ø5/16” Wall Anchors (#4.5).
13. Adjust the Stationary Panel Glass to plumb if necessary and tighten the screws. Attach the Decorative Cover (#4.4) to the L-Bar™ (#4.3). Firmly secure the L-Bar™ (#4.3) to the top of the Panel Glass using the clear gasket and rubber-tipped set screws. (Fig 13) 0-1 10 /16 "(2 mm ) 11 12 Fig 13 14. Apply a good quality mildew-resistant silicone along the connection of the Wall Profile to the wall and the Panel Glass to the threshold.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2018 DreamLine.
