Installation Guide

ManualsBrandsDreamLine ManualsKitchenInfinity-Z 60 in. x 58 in. Frameless Sliding Tub Door in Brushed Nickel

INFINITY-Z manual Ver 4 Rev 4 09/2016

INFINITY-Z

SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

reserves the right to alter, modify or redesign products at any time without prior notice.

For the latest up-to-date technical drawings, manuals, warranty information or additional details

please refer to your model’s web page on DreamLine.com

Please read these instructions carefully before installing. If you have any questions regarding

installation, please contact our technical support specialists Monday through Friday 8AM – 7PM and

Saturday 9AM-5PM EST at Phone: 1-866-731-2244, Fax: 1-866-857-3638 or e-mail our technical

support group at Support@DreamLine.com

For more information about DreamLine

products please visit DreamLine.com

Model #s

SHDR-0960580-##

SHDR-0948720-##

SHDR-0960720-##

##=finish

01-Chrome

04-Brushed Nickel

FR-Frosted Glass

Summary of content (14 pages)

PAGE 1
INFINITY-Z SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com Model #s SHDR-0960580-## SHDR-0948720-## SHDR-0960720-## ##=finish 01-Chrome 04-Brushed Nickel FR-Frosted Glass Please read these instructions carefully before installing.
PAGE 2
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
PAGE 3
Tools Required INFINITY-Z manual Ver 4 Rev 4 09/2016 3
PAGE 4
Detailed Diagram of Shower Door Components Packing List 01 02 03 04 05 06 07 08 09 Glass profile Wall profile Guide rail (Top and Bottom) Door Glass Stationary glass Handle Anti-water strip (2 long, 1 short) Single side strip Truss head screw ST4.2×40 2pcs 2pcs 2pcs 1pc 1pc 1pc 3pcs 1pc 8pcs 10 11 12 13 14 15 16 17 18 Round head screw ST4.2x25 Round head screw ST4.2x10 Flat head screw ST4.
PAGE 5
Shower Door Installation 1. Measure the distance between the two finished walls at the top (at model height: 58” or 72”), middle and bottom. The wall profiles will adjust for out-ofplumb conditions, so use the smallest measurement as the “finished opening” dimension to determine the finished cut length in step#2. See Fig. 1 for details. Top Middle NOTE: The Top and bottom Guide Rails (03) are shorter than the model size by design.
PAGE 6
3. After the Top and bottom guide rails (03) have been cut, you will need to re-install the roller stopper on each Top and bottom guide rails (03) on the end that has been cut off (the door end). Remove the existing stopper. Mark the drilling hole at a distance of 3-1/8” from the cut end of the Top and bottom Guide rail (03). Drill a new hole using an Ø1/8” drill bit; then re-secure the stopper with the screw. 1 3 1/8” ATTENTION: Do not drill the Guide rail throughout, only through the first layer.
PAGE 7
5. Slide the Stationary glass (05) fully into the groove of the Glass profile (01), and then secure the Glass holder (16) to the bottom Guide rail (03) with the Flat head screw ST4.2 x 16 (12). See Fig. 6 for details. TIP: Apply a thin bead of silicone to the bottom rail prior to setting your glass. See the detail below. Fig. 6 6. Starting from the bottom, insert the Single side strip (08) into the groove between the glass and the glass profile using a wooden or plastic shim.
PAGE 8
. Slide the Wall profiles (02) all the way onto the Glass profiles (01) on both sides. Make sure the flange of the wall profile faces inside the shower. inside See Fig. 8 for details. Fig. 8 9. Move the assembled frame into the designated position on the shower base*, bathtub or threshold (depending on your installation), and push the Wall Profiles (02) tight to the walls to compensate for any out-of-plumb conditions.
PAGE 9
10. Use a helper to hold the assembly in position and mark the drill holes on the wall through the holes on the flange of the Wall Profiles (2). Gently set the assembled unit aside; drill the holes using a Ø 5/16” drill bit and insert the Wall anchors (14). Apply silicone along the wall profile and around the holes on the wall. Also apply silicone caulk under the bottom Guide rail (03).
PAGE 10
12. Fasten the top and the bottom Wheel assemblies (17) to the Door Glass (04). The top wheels can adjust the door level using the adjustable bolt and lock nut. The bottom wheel has a press button to fix the wheel onto the bottom Guide rail (03). The wheels will face towards the outside of the shower. 1 4 2 5 3 6 Note: The lock nut of the upper wheel (Fig 12.4) and the press button of the bottom wheel (Fig 12.1) should be pointing up. See Fig. 12 for details. inside Fig. 12 13.
PAGE 11
14. Install the Handle (06) to the Door Glass (04). Press the anti-water strips (07) onto the vertical edges of the Stationary glass (05) and both vertical edges of the Door Glass (04). Insert the Seal gasket (15) into the Glass profile (01) starting from the bottom. (Fig. 14.3) 1 outside See Fig. 14 for details. 2 TIP: The longer anti-water strips (07) attach to the edges of the Door Glass (04) and the shorter strip attaches to the edge of the Stationary glass (05). 3 Fig. 14 15.
PAGE 12
16. Apply good quality mildew-resistant silicone along the profiles and guide rails; on the seams between the bottom guide rail and the profiles as well as along the shower base or threshold. Allow 24 hours for the silicone to cure before using the shower. See Fig. 16 for details. 24 H 24 h Waterproof Silicone INFINITY-Z manual Ver 4 Rev 4 09/2016 Fig.
PAGE 13
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
PAGE 14
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.