MIRAGE-X / BELLA SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the buildup of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a soft cloth. MIRAGE-X / BELLA manual Ver 1 Rev 4 07/2017 ©2017 DreamLine.
Table of Contents Section title Model Diagram Page # 2 Preparation Tools 3 Parts List 5-6 Installation Steps Bumpers 7-24 11-13 L-Bar 11, 15-16 Roller Assembly 17-18, 21-22 Vinyl Seals 20 & 23 Product maintenance 25 MIRAGE-X / BELLA manual Ver 1 Rev 4 07/2017 4 ©2017 DreamLine.
Model Diagram L- Bra 5 t cke 9 11 PAN EL DOO R 4 ©2017 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Power Drill Professional grade Glass suction cup Tape Measure Hammer Phillips Screwdriver Pencil Miter Saw or Hacksaw Silicone Drill bit (Ø8mm) (Ø5/16") Drill bit (Ø3mm) (Ø1/8") Carpenter’s Square Razor Knife Top Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. Middle Bottom Tip: Set screw gun clutch to low setting when installing screws and bolts to prevent stripping the heads. W ©2017 DreamLine.
Detailed Diagram of shower door components L-Bar (Left ) L-Bar (Right ) 6 7 5 9 1 2 10 11 12 PAN EL DOO R 4 13 DOOR EL PAN 14 15 3 16 17 18 19 20 21 ! Left-hand door installation ©2017 DreamLine. All Rights Reserved Right-hand door installation NOTE: This model is available in either a shower height or a tub height. This manual will describe the installation steps showing a shower height model. Please follow the same sequence of installation steps for the tub height model installation.
Parts List Item# PART NUMBER ITEM QTY Item# PART NUMBER ITEM QTY 01 010260003 Stationary Panel Glass 1pc 12 07121063 Bottom Rail insert 1pc 02 010260006 Door Glass 1pc 13 063007100-1804 Bottom seal strip 1pc 03 04170011-1574 Bottom Guide Rail 1pc 14 07551088 0.5mm Bottom Spacer Strip 1pc 04 07221002 Handle (203mm centers) 1pc 15 098002/098003 Allen Wrench 2.5mm,3mm 1ea 05 07121048 L - Bar™ (Left and Right) 1set 16 091105 Round Head screw ST4.
Installation steps 1. Measure the finished opening at the top, middle and bottom. The bottom width dimension will be “W”. Also check the threshold for level and the walls for plumb. Note that this model will provide up to 3/8” of adjustment for out-of-plumb conditions within the U-Channel on the panel side only. (Fig 1) This model requires a minimum threshold width of 1-3/8” Fig 1 2. Subtract 1/16” from your “W” dimension. (W (-)1/16” = L) “L” = finished cut length.
3. Place the Bottom Guide Rail (#03) onto the threshold and mark its position. Use a tape measure to keep Bottom Guide Rail (#03) parallel with the outside edge of the threshold. (Fig 3) threshold Fig 3 4.
5. Position the Wall Profile/U-Channel (#17) against the wall, on top of the Bottom Guide Rail (#03), and flush with the outside of the Bottom Guide Rail (#03). Adjust to plumb using a level. (Fig 5) Fig 5 position on the wall and also mark the hole locations for drilling. Remove the Wall Profile/ U-Channel (#17) and drill Ø5/16”(6mm) holes into the wall. Insert the Wall Anchors (#06). Apply a bead of silicone to the wall or to the back of the Wall Profile/U-Channel (#17).
7. Cut the 0.5mm Bottom Spacer Strip (#14) into three to four 2” pieces and place them into the Bottom Guide Rail (#03) to protect the bottom edge and corners of the Stationary Panel Glass (#01). (DO NOT install one long continuous strip). (Fig 7) cut 2”pcs 0.5mm Bottom Spacer Strip (#14) Wi Pa dth o ne f lG las s Fig 7 8. Dry fit the Stationary Panel Glass (#01) into the Wall profile/U-Channel (#17) and Bottom Guide Rail (#03). (Fig 8) ©2017 DreamLine.
9. Position the L-Bar™ (#05) onto the Stationary Panel Glass (#01) as shown and mark the position on the wall. Remove the Wall Plate (#5.6) and mark the holes for drilling. Drill two Ø5/16”(8mm) holes and insert the Wall Anchors (#06). Attach the Wall Plate (#5.6) using ST4.2 x 40 (#5.7) screws. (Fig 9) (See Page 15 for additional L-Bar details) 1 2 3 4 5 6 Ø5/16" (8mm) 7 Fig 9 NOTE: The top Bumper (#11) needs to be installed with ass 11.2 11.1 11.4 11.
10. Remove the Stationary Panel Glass (#01) and the 2” pieces of the 0.5mm Bottom Spacer Strips (#14). (Fig 11) Fig 11 11. To install the top Bumper (#11): Remove the Bumper insert (#11.1) and hold the Bumper base (#11.2) in place against the Wall profile/U-Channel (#17) below the L-Bar™ (#05) (Fig #12.1) to mark the position on the wall and to mark the hole for drilling. Drill a Ø5/16” hole and insert a Wall anchor (11.4). Clean the area with an alcohol swab.
12. To install the bottom Bumper (#11); First, clean the area with an alcohol swab. Remove the 3M tape backing from the Bumper (#11) and install the Bumper (#11) onto the Bottom Rail (#03) firmly against the wall and the Wall profile/U-Channel (#17). (Fig 13) 1 (Attaching the bottom Bumper (#11) with a screw is optional) Remove the 3M tape backing u-channel 2 bottom rail inside Fig 13 13. Apply silicone into the Wall profile/U-Channel ©2017 DreamLine.
14. After applying silicone into the Bottom Guide Rail (#03), add the 2” pieces of the 0.5mm Bottom Spacer Strip (#14) into the Bottom Guide Rail (#03) to protect the bottom edge and corners of the Stationary Panel Glass (#01). (DO NOT install one long continuous strip). (Fig 15) Wi Pa dth o ne f lG las s Fig 15 15. Re-install the Stationary Panel Glass (#01) ©2017 DreamLine. All Rights Reserved into the Wall profile/U-Channel (#17) and Bottom Guide Rail (#03).
12. After the Stationary Panel Glass (#01) is installed into the Wall Profile/U-Channel (#17), install the L-Bar™ (#5.3) to the Wall Plate (#5.6). (Fig 17 and Fig 18) Left L-Bar™ installation shown as an example 5.4 5.5 5.6 5.7 5 5.3 5.8 5.2 5.1 L-Bar parts list 5.1 Rubber pad 2pcs 5.2 M5 rubber tip set screw 2pcs 5.3 L-Bar 1pc 5.4 Decorative cover 1pc 5.5 Wall Anchor 2pcs 5.6 Wall plate 1pc 5.7 ST4.2x40 2pcs 5.8 M5x14.5 Screw 2pcs ©2017 DreamLine.
13. Re-attach the L-Bar™ (#5.3) to the Wall Plate 1 (#5.6) and adjust the angle (+/-)3/16” (4mm) if necessary using the set screws (Fig 19.3 and 19.4). Tighten all screws and attach the Decorative Cover (#5.4). Secure the L-Bar™ (#05) to the top of the Stationary Panel Glass (#01) using the clear gasket and rubber-tipped set screws. (Fig 19 and Fig 20) 3 2 Ma 4 Max 3/16” (4mm) 5 m) m ”(2 /16 x3 /16 ”(4 mm ) 6 0-1 ©2017 DreamLine.
Bottom Roller Assembly (#10) Parts List 10.1 Roller body (exterior) 1pc 10.2 Rubber pad 1 2pcs 10.3 Rubber pad 2 1pc 10.4 Bearing 1pc 10.5 Adjustment disk 1pc 10.6 M5x14 Allen Bolt 4pcs 10.7 Cover plate 1pc 10.8 Decorative cover plate 1pc 10.9 M5x16 Allen Bolt 2pcs 10.6 10.9 10.8 10.6 10.7 10.5 10.4 10.3 10.2 10.
15. Set the Door Glass (#02) with the attached Bottom Roller Assemblies (#10) onto the Bottom Guide Rail (#03). Have an assistant available to support the Door Glass (#02) for the next few steps. (Fig 18) NOTE: Use caution to prevent the door glass from making contact with the wall during installation. ©2017 DreamLine.
Guide Block Assembly (#09) Parts List 1 9.1 Exterior Slider Bracket (for panel) 1pc 9.2 Gasket 2pcs 9.3 Rubber sleeve 2pcs 9.4 Shaft 2pcs 9.5 Sliding pad 1pc 9.6 Sliding Guide Block (for door) 1pc 9.7 M5x10 set screw 2pcs 9.8 M4x4 flat head screw 2pcs 9.8 9.7 9.6 9.2 9.3 9 2 9.4 9.1 9.5 Fig 19 ©2017 DreamLine. All Rights Reserved 16. Attach the Exterior Slider Bracket (#9.1) through the notch of the installed Stationary Panel Glass (#01) as shown in Fig 19.
17. Install the Handle (#04) to the outside of the 1 Door Glass (#02). (Fig 21.1) 2 Attach the Bumper Seal Strip (#13) to the closing edge of the Door Glass (#02). (Fig 21.2) (Fig 21) doo r 18. Measure from the edge of the installed Stationary Fig 21 Panel Glass (#01) to the wall and cut the Bottom Rail Insert (#12) to this dimension: W (-) 1/16”. Use a metal file to file off any burrs from the cut end. Apply silicone into the Bottom Guide Rail (#03) and install the Bottom Rail Insert (#12).
19. The door should operate smoothly and create a good seal with the wall when in the closed position. If necessary, adjust the Bottom Rollers (#10) as shown to tilt the door slightly for a good seal with the wall. Loosen the center M5 x 14 Allen Bolts (#10.6) and then rotate the Adjustment Disk (#10.5) using the Roller Adjustment Tool (#20) as shown. Use shims or an assistant to hold the Door Glass (#02) in the desired position and re-tighten the allen bolt. Only adjust one roller at a time.
20. Attach the roller Cover Plate (#10.8), leaving approximately 1/16” of clearance beneath the bottom rail. Re-adjust the plate if it makes contact with the bottom rail. (Fig 25) ©2017 DreamLine.
21. Remove the paper strip from the adhesive backing of the Bottom Deflector (#18) and attach all three strips to the bottom edge of the Door Glass (#02) as shown. Attach the Anti-water side strip (#19) to the edge of the Door Glass (#02). Notch off the inside bottom to fit around the Bottom Deflector (#18). Also, notch the bottom of the Bumper Seal Strip (#13) to fit around the Bottom Deflector (#18). (Fig 26). NOTCH OUT TO FIT AROUND L-BAR panel door inside inside door ©2017 DreamLine.
22. Apply a good quality, mildew-resistant silicone along the U-Channel and Bottom rail. (Fig 27) ! Allow 24 hours for the silicone to fully cure before first use. ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2017 DreamLine.