MIRAGE SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the rights to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Shower/Tub Door Components 6 7 1 8 5 2 9 10 20 11 12 19 13 4 15 16 17 3 18 21 Parts List 01 02 03 04 05 06 07 08 09 10 Stationary glass A Glass door Guide rail Handle Support bar Wall anchor Round head screw ST4.2×55 Guide rail connector Sliding bracket assembly Roller assembly 1pc 1pc 1pc 1pc 1pc 6pcs 6pcs 1pair 1pc 2pcs 11 12 13 15 16 17 18 19 20 21 Stopper block Wall bracket Single side strip Seal gasket Countersunk screw ST4.
Sliding Bracket Assembly A D E F B C G H I J A B C D E Face Plate Back Plate Slider 1/16” PVC gasket 1/16” PVC washer “MIRAGE – 60” Rev. 3 Ver.
Shower/Tub Door Installation NOTE: The installation of this door requires two installers. NOTE: The door can be installed on the shower base, tub or custom threshold. 1. Measure the distance between two walls. This distance is marked as “W”. See Fig. 1 for details. W Fig. 1 2. Your Guide rail (03) has been precut for your Shower model opening width: 60”. If W-width of your wall-to-wall opening is equal to 60” it is unnecessary to cut the Guide rail and you can continue to Step#3.
3. Fasten the Guide rail connector (08) to one of the sides of the Guide rail (03). Slide in two Roller assemblies (10) from the other end of the Guide rail. Fasten another Guide rail connector to the other side of the Guide rail. Position the Guide rail on base or threshold and trace through predrilled holes of Guide rail connector flange to mark wall. Drill the holes using Ø 5/16” drill bit and insert the Wall anchor (06). Apply a layer of waterproof silicone to the bottom side of the Guide rail.
5. Mount the Wall bracket (12) to Stationary glass A (01). Slide the glass into the channel of the Guide rail (03). 1 See Fig. 5 for details. 2 3 Fig. 5 6. Butt up Stationary glass A (01) against the wall and level it vertically. See Fig. 6 for details. Fig. 6 “MIRAGE – 60” Rev. 3 Ver.
7. Outline the position of the Wall bracket (12) on the wall. Set Stationary glass A (01) aside. Remove the Wall bracket from Stationary glass A and by replacing it to the outlined position mark the hole on the wall. Drill the hole using Ø 5/16” drill bit, insert the Wall anchor (06) and fasten the Wall bracket to the wall with the Round head screw ST4.2×55 (07). Put Stationary glass A back into position and tight it up to the Wall Bracket. 1 4 2 5 3 6 See Fig. 7 for details. Ø 5/16” Fig. 7 8.
. Butt up Stationary glass B (20) against the wall and level it vertically. See fig. 9 for details. Fig. 9 10. Outline the position of the Wall bracket (12) on the wall. Set Stationary glass B (20) aside. Remove the Wall bracket from Stationary glass B and by replacing it to the outlined position mark the hole on the wall. Drill the hole using Ø 5/16” drill bit, insert the Wall anchor (06) and fasten the Wall bracket to the wall with the Round head screw ST4.2×55 (07).
11. Push the Single side strip (13) between the groove of the Guide rail (03) and both Stationary glasses A & B using wooden shims or other piece of wood. 1 See fig. 11 for details. 2 Fig. 11 12. Glass shelves (19) are installed to Stationary glass B (20). Mark the Glass shelf position on the wall. According to the measurements in Fig. 12.1, mark drill holes for the shelf brackets. Drill the holes using Ø 5/16” drill bit and insert the Wall anchors (06).
Fig. 13 1 NOTE: Please refer to Sliding bracket assembly (09) diagram on Page 4. 13. Disassemble the Sliding bracket assembly. Mount the Face Plate (A) and Back Plate (B) on the top of Stationary glass A (01) with the Head screw M6×16 (G). Use PVC gasket (D) and PVC washer (E) in between glass and metal parts. NOTE: Use only hand tools. Do not over tighten the screws. 2 See Fig. 14 and Fig. 15 for details. Fig. 14 “MIRAGE – 60” Rev. 3 Ver.
Fig. 15 14. Install the Stopper block (11) on the bottom of the Glass door (02). See fig. 16 for details. 1 2 Fig. 16 “MIRAGE – 60” Rev. 3 Ver.
15. Bring the Glass door (02) inside the shower. Remove nuts from the Roller assembly (10) bolts and spread the rollers against the installation holes on the Glass door. Fasten the Roller assembly to the Glass door through the predrilled holes. NOTE: Steps 15 and Steps 16 require second person to hold Glass door. The Glass door will not stay by itself until you finish the Step 16. 1 3 2 4 See Fig. 17 for details Fig. 17 NOTE: Please refer to Sliding bracket assembly (09) diagram on Page 4. 16.
Fig. 19 17. Press the Magnetic strip (21) on the vertical edge of the Glass door (02) and Stationary glass B (20). Push the Seal gasket (15) into the channel of the Guide rail (03). 1 3 2 4 See Fig. 20 for details. Fig. 20 “MIRAGE – 60” Rev. 3 Ver.
18. Install the Handle (04) onto the Glass door (02). See fig. 21 for details. Fig. 21 1 19. Locate the Support bar (05) and temporarily fasten it to the Sliding bracket assembly (09) with the Head screw M6×8 (H). Adjust the bar to a proper position and level it horizontally. Hold it firmly and outline the wall bracket of the Support bar to mark wall with position. Remove the Support bar and detach its wall bracket.
20. Apply the sealant along the connection of Stationary glasses A and B with the wall inside the shower, as well as between the Guide rail (03) and the threshold outside the shower. See Fig. 23 and Fig. 24 for details. caulk Fig. 23 caulk Fig. 24 “MIRAGE – 60” Rev. 3 Ver.
NOTICE: The above installation steps are given for the right-hand configuration. For left-hand configuration door, please reverse Stationary glass A and B and attach the Sliding bracket assembly (12) to Stationary glass A. See Fig. 25 for details. Fig. 25 Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors and Tub Doors please visit www.BathAuthority.