Aqua Swing Tub Door & EX/RT Panel TUB DOOR AND PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
AQUA SWING SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or additional details please refer to your model’s web page on DreamLine.com. Left hand installation shown Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Detailed Diagram of Shower door Components 01 03 04 05 02 06 07 11 08 09 10 Packing list 01 02 03 04 05 06 Wall profile Glass door with Hinged glass profile Wall anchor Big head screw ST4.2×55 Round head screw ST4.2×16 Decorative plug and washer 1pc 1set 4pcs 4pcs 3pcs 3sets 07 08 09 10 11 Threshold connector (left/right) Aluminum threshold Bottom anti-water strip Threshold end cover (left/right) Handle 1set 1pc 1pc 1set 1pc NOTE: Unpack your unit carefully and inspect it.
Shower door installation 1. Prepare your finished opening for installation. Clean all surfaces and remove any debris or construction materials. See Fig 1. NOTE: This model is reversible for left or right hand installation. This manual will show the left hand installation. For a right hand installation, simply begin on the opposite wall and reverse the orientation of the parts as necessary. Fig 1 2.
3. Mark the drill holes on the wall through the predrilled holes in the Wall profile (01). Now drill holes in the wall using a Φ5/16 drill bit and insert the Wall anchors (03). Apply silicone along the back of the Wall profile and into the drill holes. Fasten the Wall profile to the wall with the Big head Screw ST4.2x40 (04). See Fig 3. Φ8mm Φ5/16” 1 4 2 5 3 Fig 3 4. Slide the assembled Glass door with Hinged glass profile (02) into the groove of the Wall profile (01) and level it vertically (Fig 4.
5. Snap the Aluminum threshold (08) into the Threshold connector (07) and Threshold end cover (10). Left hand installation shown Run a bead of Waterproof silicone along the bottom of the Aluminum threshold. Attach the Aluminum threshold onto the tub, parallel to the tub edge with the Threshold connector tight to the bottom and even with the outside of the Hinged glass profile (Fig. 5.4). Run a bead of Waterproof silicone along the connection of the Threshold connector and Hinged glass profile. See Fig 5.
Fig 8 8. Allow 24 hours for the silicone to fully cure before using your new shower. See Fig 9 and See Fig 10.
Product Maintenance BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.
EXTENDER Panel (EX) / RETURN Panel (RT) EX / RT STATIONARY PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
Table of Contents Section title Page # Aqua Series with Extender (EX) or Return (RT) Panel Model #s 3 Preparation Tools 4 Parts Diagram/Packing List Installation Steps 6 7-14 Product Maintenance 15 ©2017 DreamLine.
Aqua Tub -EX Aqua Tub -RT AquaLux-Tub -EX AquaLux-Tub -RT SHDR-3148586-EX-01 SHDR-3148586-EX-04 SHDR-3148586-RT-01 SHDR-3148586-RT-04 SHDR-3348588-EX-01 SHDR-3348588-EX-04 SHDR-3348588-RT-01 SHDR-3348588-RT-04 Aqua-Ultra Tub-EX Aqua-Ultra Tub-RT Aqua Uno-Tub-EX Aqua Uno-Tub-RT SHDR-3534586-EX-01 SHDR-3534586-EX-04 SHDR-3534586-RT-01 SHDR-3534586-RT-04 SHDR-3448580-EX-01 SHDR-3448580-EX-04 SHDR-3448580-RT-01 SHDR-3448580-RT-04 Aqua Fold-Tub -EX Aqua Fold-Tub -RT Aqua Swing-Tub-EX Aqua Swin
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Silicone Power Drill Pencil Phillips Screwdriver Drill bit (Ø=5/16”) Drill bit (Ø=1/8”) Hammer ©2017 DreamLine. All Rights Reserved Level Tape Measure NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in this manual as a reference. Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine® for replacement.
Parts Diagram Parts Diagram A Parts Diagram B 9” x 58” Extender Panel (EX) 30” x 58” Return Panel (RT) 1 1 4 4 5 6 3 5 3 6 2 2 Packing List PART# DESCRIPTION QTY PART# DESCRIPTION QTY 01 02 03 U-Channel 1 (58” wall profile) U-Channel 2 (9” bottom profile) Extender panel glass 1pc 1pc 1pc 04 05 06 Ø5/16” Wall anchor Countersunk screw ST4.2x40 Countersunk screw ST4.
Installation steps 9” In-Line Extender Panel Installation (EX) NOTE: The following panel installation instructions apply to all of the Aqua series tub doors. Please install whichever Aqua model tub door you purchased prior to proceeding with the following Stationary Glass installation instructions. Please see the Shower / Tub Door Installation manual included in the door packaging for complete tub door installation instructions. NOTE: Use Parts Diagram “A” for the EX panel assembly and installation.
2. Remove the U-Channel 1 (wall profile) (#01) and U-Channel 2 (bottom profile) (#02) from the Extender Panel Glass (#03) and carefully set the Extender Panel Glass (#03) aside. Place the U-Channel 2 (bottom profile) (#02) back onto the tub surface in line with the inside U-Channel mark. Mark the drill holes on the tub surface through the pre-drilled holes in the U-Channel 2 (bottom profile) (#02) and drill the holes using an Ø1/8” drill bit.
4. Apply waterproof silicone into both U-Channels. (Fig 5) NOTE: The surface needs to be clean and free of debris before applying silicone. 1 2 Fig 5 5. Slide the Extender Panel Glass (#03) into the installed U-Channels. NOTE: If you have difficulty sliding the Extender Panel Glass (#03) into the U-Channels, you can use a small block of wood and a rubber mallet to lightly tap on the Extender glass until the glass is firmly set in the U-Channel.
6. Apply a good quality mildew-resistant waterproof silicone along the connection of both U-Channels to the wall and tub surface from the inside of the shower. (Fig 7) ! Allow 24 hours for the silicone to fully cure before using the shower. ©2017 DreamLine.
30” Return Panel Installation (RT) NOTE: The following panel installation instructions apply to all of the Aqua series tub doors. Please install whichever Aqua model you purchased prior to proceeding with the following Return Glass installation instructions. Please see the Shower / Tub Door Installation manual included in the door packaging for complete tub door installation instructions.
8. Place the U-Channel 2 (bottom profile) (#02) onto the tub surface in line with the inside U-Channel mark. Mark the drill holes onto the tub ledge through the predrilled holes in the U-Channel 2 (bottom profile) (#02) and drill the holes using a Ø1/8” drill bit. Apply waterproof silicone along the bottom surface and around the holes of the U-Channel 2 (bottom profile) (#02) and fasten it to the tub ledge with the Countersunk Screws ST4.2×25 (#06).
10. Apply waterproof silicone into both U-Channels. (Fig 12) NOTE: The surface needs to be clean and free of debris before applying silicone. 1 2 Fig 12 11. Slide the Return Panel Glass (#17) into the groove of the installed U-Channels. NOTE: If you have difficulty sliding the Return Panel Glass (#17) into the U-Channels, you can use a small block of wood and a rubber mallet to lightly tap on the Extender glass until the glass is firmly set in the U-Channel.
12. Apply a good quality mildew-resistant waterproof silicone along the connection of both U-Channels to the wall and tub surface from the inside of the shower. (Fig 14) ! Allow 24 hours for the silicone to fully cure before using the shower. ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
©2017 DreamLine. All Rights Reserved TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.