MIRAGE-X ® e SHOWER AND TUB DOOR iIn NSTALLATION vedINSTRUCTIONS r L e s m e PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION a R e r s D ght © Ri All d e e in erv L s m e a R e r s D ght © Ri All ® MODEL #s SHDR-1948723L-## SHDR-1960723L-## SHDR-1960580L-## SHDR-1948723R-## SHDR-1960723R-## SHDR-1960580R-## ## = finish 01 - Chrome 04 - Brushed Nickel G - Gray Glass *Right-hand door installation shown IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time with
This model is treated with DreamLine’s exclusive ClearMax® Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots. Install the surface with the ClearMax® label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a ® soft cloth.
Section Title Page # ClearMax® Coating Information Warnings and General Preparation Model Specific Preparation Tools ® Detailed Diagram of Shower and Tub Door Components Parts List Installation Steps SafeStop™ Bumper Installation L-Bar™ Support Bracket Installation Bottom Roller Assembly Installation Guide Block Assembly Installation Handle and Bulb Vinyl Installation Deflector Vinyl and Vertical Vinyl Seal Installation Product Maintenance Troubleshooting Bottom Roller Assembly Adjustment Procedure Factor
©2020 DreamLine® All Rights Reserved WARNING DISCLOSURE STATEMENT d e e in erv L s m e a R e r s t D gh © Ri l l A ® GENERAL PREPARATION IMPORTANT • • • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2020 DreamLine® All Rights Reserved ! Model Specific Preparation REQUIRED: 1-1/2” minimum threshold d e e n v i r L e s m e a R e Dr ghts © Ri All ® ±0.0 ±0.0 1-1/2” minimum threshold ±0.0 *left-hand L-Bar™ Support Bracket shown NOTE Tile TIP ! Acrylic Tub This manual will describe the shower/tub door installation using the L-Bar™ Support Bracket in the left-handed orientation (as shown above). To reverse the L-Bar™ orientation please use the supplied right-hand L-Bar™ Support Bracket.
©2020 DreamLine® All Rights Reserved Tools Level Tape Measure Phillips Screwdriver Pencil 100% Silicone d e e n v i r L e s m e a R e Dr ghts © Ri All Power Drill ® Drill Bit Ø1/8" (3mm) Drill Bit Ø3/16" (4mm) Razor Knife Drill Bit Ø5/16" (8mm) Soft Head Hammer Professional-grade Glass suction cup Mitre Saw Extender Driver Bit Hacksaw Carpenter’s Square Safety Glasses TIP Measure the finished opening before proceeding with the installation to be sure that the correct model size has bee
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Detailed Diagram of Shower/Tub Door Components ® 09 d e e in erv L s m e a R e r s t D gh © Ri All 04 13 07 05 17 01 02 Inline panel Door 03 12 11 ® inside 19 18 e r n i L e s m e a sR e r D ght © Ri l l A d e v *Right-hand door installation shown inside 16 10 5 © 2020 DreamLine® All Rights Reserved
©2020 DreamLine® All Rights Reserved Parts List 01 02 03 d e e n v i r L e x1 x1 s m e a R e Dr ghts © R05i 06 l Al ® Inline Panel Glass 04 Handle Door Glass x1 07 ST4.
©2020 DreamLine® All Rights Reserved Parts List 14 15 16 d e e n v i r L e x1 x1ea s m e a R e Dr ghts © R18i 19 l Al ® PVC Glass Spacer 0.5mm (x 36” roll) 17 U-Channel 1” Aluminum Allen Wrench (2.5, 3 mm) x1 20 Roller Installation Tool ST4.0 x 30mm Pan Head Screw Deflector Vinyl (with VHB tape) x3 Vertical Vinyl Strip x3 x1 21 d e e x3 n v i r L e s m e a R e Dr ghts © Ri All x1 ST4.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Installation Steps ® 1 Top *at model height ________” d e e in erv L s m e a R e r s t D gh © Ri All Middle ________” Bottom ________” d e e n v i r L e Fig 1 m s e a R e r s t D gh © Ri l l A W ® NOTE This model will provide up to 3/8” of adjustment for out-of-plumb conditions within the U-Channel (#17) on the panel side only. NOTE Decide on the handing of the shower door based on your bathroom configuration.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 2 After determining the handing of the installation: Only cut from the end of the Bottom Guide Rail (#03) that will® be installed on the door side of the opening.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 3 d e e in erv L s m e a R e r s t D gh © Ri All ® d e e n erv Fig 3 Li s m e a R e r s t D gh © Ri l l A ® NOTE Mark the position of the Bottom Guide Rail (#03) on the threshold. Use a tape measure to align the rail parallel with the outside edge of the threshold. Mark the holes for drilling through the predrilled holes in the Bottom Guide Rail (#03).
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 4 1 2 3 d e e in erv L s m e a R e r s t D gh © Ri All ® *see NOTE Parts Needed 16 x3 d e e n 4 erv iFig L s m e a R e r s t D gh © Ri l l A ® NOTE ◾For installation into an Acrylic Threshold: drill a Ø1/8”(3mm) hole and use the ST4.0 x 30mm Pan Head Screw (#16) OR ◾For installation into a Tile Threshold: drill a Ø3/16”(4mm) hole up to the stud and use the ST4.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 5 d e e in erv L s m e a R e r s t D gh © Ri All ® ±0.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 6 1 2 d e e in3 erv L s m e a R e r s t D gh © Ri All ® Ø3/16” or Ø5/16” *see NOTE 4 5 Parts Needed 06 *see NOTE x4 07 d e e in erv Fig 6 L s m e a R e r s t D gh © Ri l l A ® NOTE x4 Tools Needed ◾If a stud is present behind the wall: drill a Ø3/16”(4mm) hole and use the ST4.2 x 40mm Countersunk Screws (#07) OR ◾If no stud is present behind the wall: drill a Ø5/16”(7mm) hole and insert the Wall Anchors (#06) and use the ST4.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 SafeStop™ Bumper Installation 7 d e e in11 erv L s m e a R e r s D ght © Ri All ® 11.2 11.1 11.4 11.3 Item Item Description Quantity 11.1 11.2 11.3 11.4 Bumper Insert Bumper Base ST4.2 x 40mm Countersunk Screw Wall Anchor 1pc 1pc 1pc 1pc TIP 3M™ Tape The surfaces need to be clean and free of construction debris before installing the SafeStop™ Bumper(s) (#11). Clean the area with an alcohol swab before installation.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 7 1 inside 1” 4 d e e in erv L s 1” m e a R e r s t D gh © Ri All 2 3 ® insid e u-channel 5 6 *see NOTE Ø3/16” or Ø5/16” REMOVE 3M™ TAPE *see NOTE 7 8 Parts Needed 11 d e e in erv Fig 7 L s m e a R e r s t D gh © Ri l l A ® NOTE TIP Extender driver bit recommended for screw installation. x1 Tools Needed 15 ◾If a stud is present behind the wall: drill a Ø3/16”(4mm) hole up to the stud and use the ST4.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 8 1 REMOVE 3M™ TAPE 2 3 d e e in erv L s m e a R e r s t D gh © Ri All u-ch ® ann el bot to rail m outsid insid e d e e in erv L s m e a R Fig 8 e r s t D gh © Ri l l A e ® TIP For the bottom SafeStop™ Bumper (#11): The Adhesive installation method is shown. Attaching the bottom SafeStop™ Bumper with a screw is optional. Follow the procedure shown in Step 7 for installing the bottom SafeStop™ Bumper (#11) with the ST4.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 9 d e e in erv L s m e a R e r s t D gh © Ri All ® Widt h e Pa of nel G lass d e e in Fig 9erv L s m e a R e r s t D gh © Ri l l A Inlin NOTE ® Tools Needed Apply 100% silicone caulk into the vertical U-Channel (#17) and into the Bottom Guide Rail (#03).
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 10 d e e in erv L s m e a R e r s t D gh © Ri All ® 2” (50.8mm) Fig 10 ® ! e r n i L e s m e a sR e r D ght © Ri l l A d e v Cut several 2” - 3” pieces of the the PVC Glass Spacer 0.5mm (#14). DO NOT install one long continuous piece into the Bottom Guide Rail (#03).
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 11 d e e in erv L s m e a R e r s t D gh © Ri All ® d e e in erv L s m e a R e r s Fig 11 t D gh © Ri l l A ® Widt h e Pa of nel G las Inlin s TIP Save the remaining 2” pieces of the PVC Glass Spacer 0.5mm (#14) for later use.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 12 3/8” MAX + 3/8” max d e e in erv L s m e a R e r s t D gh © Ri l 1Al ® 2 d e e in erv L s m e a R e Fig 12 r s t D gh © Ri l l A ® NOTE NOTE Leave the corner protectors on the glass until it is necessary to remove them. Parts Needed 01 x1 Tools Needed The panel-side U-Channel (#17) will allow for up to 3/8” of out-of-plumb adjustment. Use a level to confirm that the Inline Panel Glass (#01) is installed plumb and level.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 L-Bar™ Support Bracket Installation ® 13 d e e in erv 05 L s m e a R e r s t D gh © Ri All 5.6 5.5 5.8 5.4 5.7 5.2 5.3 5.1 Left-handed L-Bar™ Support Bracket shown* Item 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 NOTE Item Description Rubber Pad M5 Rubber Tip Set Screw L-Bar™ Bracket L-Bar™ Bracket Decorative Cover Wall Anchor L-Bar™ Bracket Wall Plate Truss Head Screw ST4.2×40 M5×14.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 14 1 2 5 6 ® in3e d e rv L e s m e a sR e r D ght © Ri All 4 7 Fig 14 Left-hand L-Bar™ Support Bracket shown* d e e in erv L s m e a R e r s t D gh © Ri l l A ® TIP Tools Needed Leave the L-Bar™ decorative cover attached when marking the L-Bar position on the wall to allow space to re-attach the cover plate after installation.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 15 d 3 e e in erv L s m e a R e r s t D gh © Ri All 1 ® 2 Max 3/16” (4mm) 5 0 - 1/16” (2mm) 4 Max 3/16” (4mm) 6 d e e in erv L s m e a R e r s t D gh © Ri l l A ® Fig 15 Left-hand L-Bar™ Support Bracket shown* NOTE Confirm the Inline Panel Glass (#01) is level and plumb with the attached L-Bar™ (#05) by adjusting the angle (+/-) 3/16”. Firmly tighten the set screws before re-attaching the Decorative Cover.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 16 d e e in erv L s m e a R e r s t D gh © Ri All ® Trim Bottom Channel Insert (#12) to: (W) (-) 1/16” W- 1/16 ” PVC Glass Spacer 0.5mm (#14) OR Fig 16b W- 1/16 ” ® Fig 16a TIP ! Use a metal file to deburr the cut end W e r n i L e s m e a sR e r D ght © Ri l l A d e v To prevent glass-to-metal contact, insert a small piece (1/4” +/-) of the leftover PVC Glass Spacer 0.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Bottom Roller Assembly Installation 17 d e e in erv L s m e a R e r s t D gh © Ri All ® 10.8 10.6 10.9 10.4 10.2 10.7 10.5 10.6 10.3 10 10.1 NOTE ! DO NOT completely disassemble the Bottom Roller Assembly (#10) during installation. outside Item Item Description Quantity 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 17 1 2 4 ® i3ne L e s m e a sR e r D ght © Ri All 5 inside d e rv inside 6 inside inside Fig 17b d e e in erv L s m e a R e r s t D gh Fig 17c © Ri l l A ® NOTE TIP Parts Needed 02 Leave the corner protectors on the door glass until it is necessary to remove them. Make certain that the bolts are facing inside the shower and the Bottom Roller Assemblies (#10) are installed squarely onto the glass as shown in Fig 17c.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 18 For the next steps, have an assistant available to hold the Door Glass (#02) in position during the installation of the® Guide Block Assembly (#09). ! d e e in erv L s m e a R e r s t D gh © Ri All ! inside d e e in erv L s m e a R e r Fig 18ts D gh © Ri l l A ® 27 ! Tools Needed Use caution to prevent the door glass from making contact with the installed Inline Panel Glass or the wall during installation.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Guide Block Installation 19 1 2 3 inside 4 d e rv ® p an e el se n i L © am ts Re e r D Righ All inside do or Fig 19 9.7 9.1 9.3 9.2 09 9.8 9.6 ! 9.5 9.4 Use caution to prevent the unprotected edge of the door glass from making contact with the wall during installation. 9.2 Item Item Description Quantity 9.1 Exterior Slider Bracket (for panel) 1pc 9.2 Gasket 2pcs 9.3 Rubber Sleeve 2pcs 9.4 Shaft 2pcs 9.5 Sliding Pad 1pc 9.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 20 Handle and Bulb Vinyl Installation d e e in erv L s m e a R e r s t D gh © Ri All doo ® r outside d e e in erv L s m e a R e r Fig 20 s t D gh © Ri l l A ® inside Parts Needed 04 x1 13 29 x1 ©2020 DreamLine® All Rights Reserved
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 21 d e e n erv i L 2 am 3 s e R e r s t D gh © Ri All ® 1 1/16” inside d e e in erv L s m e a R e r s t D ghFig 22 © Ri l l A ® 30 ©2020 DreamLine® All Rights Reserved
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Deflector Vinyl and Vertical Vinyl Seal Installation 22 d e e in erv L s m e a R e r s t D gh © Ri All ® door glass remove tape backing inline panel glass top view of Vertical Vinyl Seal (#19) installed onto Door Glass Inline panel Door door Parts Needed 18 inside ® Door inside e r n i L e Door s m e a sR e r D ght Fig 23 © Ri l l A inside sideview of Deflector Vinyl (#18) installed onto Door Glass d e v x3 19 x1 Tools Needed 31 ©20
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 23 The surfaces need to be clean and free of debris before applying silicone. NOTE d e e in erv L s m e a R e 24 r s t D ghHours © Ri All ® d e e in erv L s m e a R e r s t FigD 24 © Righ l l A ® 32 ! Tools Needed Allow 24 hours for the silicone caulk to cure before using shower.
©2020 DreamLine® All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
©2020 DreamLine® All Rights Reserved Troubleshooting Problem/Symptom Missing Parts Bottom Guide Rail (#03) was cut too short or was cut from the wrong end during installation. Suggested Solution •Check all shipping/packaging material for missing parts/components. •If not found, contact DreamLine Customer Support [1-866-731-2244] to order factory part replacement. •Contact DreamLine Customer Support [1-866-731-2244] to order factory part replacement.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Bottom Roller Assembly Adjustment Procedure d e e in erv L s m e a R e r s t D gh © Ri All ® 1 loosen inside 2 1/16” rotate inside 3 tighten 1/16” d e e in21a erv L Fig s m e a R e r s t D gh © Ri l l A ® inside NOTE 35 ! Adjust the door glass to create a good seal with the wall by using the adjustment feature in the Roller Assemblies.
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e ITEM DESCRIPTION n erv i L 010260001 Inline Panel Glass s m e a R e 010260004 Door Glass r s t D gBottom 04170011-1270 / 04170041-1270 h Guide Rail for 10mm (3/8in) Glass © i 07221041 /07224041 R Single Sided 8" Handle Assembly wKnob l l 07121048 / 07124048 L-Bar Support Bracket 12in for 10mm (3/8in) Glass A MIRAGE-X 48x72 SHDR-1948723L-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 20 21 ® FACTORY P
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e v DESCRIPTION in eITEM FACTORY PART NUMBER r L s m 010260001 Inline Panel Glass e a R e r 010260004 DoorsGlass t D ghBottom Guide Rail for 10mm (3/8in) Glass 04170011-1270 / 04170041-1270 © Ri Single Sided 8" Handle Assembly wKnob 07221041 / 07224041 All 07121049 / 07124049 L-Bar Support Bracket 12in for 10mm (3/8in) Glass MIRAGE-X 48x72 SHDR-1948723R-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 20
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e in erv FACTORY PART NUMBER L s m 010260002 Inline PaneleGlass a R e r 010260005 Door Glass s t D ghBottom Guide Rail for 10mm (3/8in) Glass 04170011-1574 / 04170041-1574 © i R 07221041 / 07224041 Single Sided 8" Handle Assembly wKnob l l A 07121139 / 07124139 L-Bar Support Bracket 18in for 10mm (3/8in) Glass MIRAGE-X 60x58 SHDR-1960580L-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 20 21 07550045 09
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e in erv FACTORY PART NUMBER L s m 010260002 Inline PaneleGlass a R e r 010260005 DoorsGlass t D ghBottom Guide Rail for 10mm (3/8in) Glass 04170011-1574 / 04170041-1574 © i R 07221041 / 07224041 Single Sided 8" Handle Assembly wKnob l l A 07121140 / 07124140 L-Bar Support Bracket 18in for 10mm (3/8in) Glass MIRAGE-X 60x58 SHDR-1960580R-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 20 21 07550045 0921
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e v DESCRIPTION in eITEM r FACTORY PART NUMBER L s m 010260003 Inline PaneleGlass a R e r s 010260006 Door Glass t D ghBottom Guide Rail for 10mm (3/8in) Glass 04170011-1574 / 04170041-1574 © Ri 07221041 / 07224041 Single Sided 8" Handle Assembly wKnob l l A 07121139 / 07124139 L-Bar Support Bracket 18in for 10mm (3/8in) Glass MIRAGE-X 60x72 SHDR-1960723L-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 2
MIRAGE-X Shower and Tub Door Manual Ver 1 Rev 6a 082020 Factory Parts Information d e e v DESCRIPTION in eITEM r FACTORY PART NUMBER L s m 010260003 Inline PaneleGlass a R e r s 010260006 Door Glass t D ghBottom Guide Rail for 10mm (3/8in) Glass 04170011-1574 / 04170041-1574 © Ri 07221041 / 07224041 Single Sided 8" Handle Assembly wKnob l l A 07121140 / 07124140 L-Bar Support Bracket 18in for 10mm (3/8in) Glass MIRAGE-X 60x72 SHDR-1960723R-## ITEM # 01 02 03 04 05 06 07 09 10 11 12 13 14 15 16 17 18 19 2
d e e in erv L s m e a R e r s t D gh © Ri All ® d e e in erv L s m e a R e r s t D gh © Ri All ® TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.