PRISM PLUS ® d SHOWER ENCLOSURE INSTALLATION I e e n v NSTRUCTIONS i r L e s TO INSTALLATION PLEASE REVIEW THIS ENTIRE MANUAL PRIOR m e a R e r s t D gh © Ri All MODEL #s d e e in erv L s m e a R e r s t D gh © Ri All ® (Left-swing door installation shown) SHEN-2634340-## SHEN-2636360-## SHEN-2638380-## SHEN-2640400-## ##=finish 01- Chrome 04- Brushed Nickel 06- Oil Rubbed Bronze 09- Satin Black G - Gray Glass IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time w
TM that prevents the build up of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. Do not remove ClearMax stickers until after the glass is installed. For best results, squeegee the glass after ® each use and dry with a soft cloth.
Section Title Checking Dimensions Important Information Model-Specific Preparation Tools Detailed Diagram of Shower Door Components Parts List Installation Steps Adjustable Hinge Information Product Maintenance Troubleshooting Factory Parts Information Page # d e e in erv L s m e a R e r s D ght © Ri All TIP ® 2 3 4 5 6 7-8 9-29 30 31 32 33 Measure the finished opening before proceeding with the installation to be sure the correct model size has been ordered d e e in erv L s m e a R e r s D ght © Ri
NOTE: This enclosure must be installed at the model size dimensions shown in Table A on page 2 and page 9. Be sure that the correct size shower enclosure has been ordered to fit the finished dimensions of the base or threshold where the enclosure will be installed. NOTE: The thickness of the finished wall treatment will affect where the enclosure will align upon the threshold.
d e e in erv L s m e a R e r s t D gh © Ri All IMPORTANT • • • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2022 DreamLine® All Rights Reserved ! Model-Specific Preparation REQUIRED: ±0.0 ±0.0 d e e in erv L s m e a R e r s D ght © Ri All ® ±0.0 ±0.0 ! ! DO NOT install the handle onto the door glass until instructed. Acrylic Tile TIP 1-1/2” minimum threshold DO NOT lift the glass using the handle. This could result in damage to the glass and/or serious personal injury. Always use an assistant or a professional grade glass suction cup when handling heavy glass.
Tape Measure Level Pencil #2 Phillips Screwdriver d e e in erv L s m e a R e r s D ght © Ri All ® 100% Silicone* Drill bit (Ø1/8") (3mm) *Quick-drying/fast-curing Power Drill silicone recommended for the installation of hinge panels. Screw Gun 13/16” shims Professional-grade Glass Suction Cup 4mm Hex Bit #2 Phillips Driver Bit Razor Knife Soft Head Hammer Drill bit Drill bit (Ø3/16") (Ø5/16") (4.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 Detailed Diagram of Shower Door Components d 14 e e n v i r L e s m e a R e r s D ght © Ri l l A ® 13 05 03 09 01 02 06 11 12 07 ® 17 04 e r n i L e s m e a sR e r D ght © Ri All d e v 08 15 6 (Left-swing door installation shown) © 2022 DreamLine® All Rights Reserved
©2022 DreamLine® All Rights Reserved Parts List 02 01 Return Panel Glass x1 03 Door Glass 05 04 L-Bar™ Support Bracket (Right & Left) x2 x1 Wall Anchor 8mm (5/16”) x8 130º Glass-to-Glass Hinge Assembly U-Channel 1” Stainless Steel for 10 mm (3/8”) glass x2 Handle x2 Decorative Cover and washer 13 2 ea d e e in erv L s m e a R e r s t D gh © x2Ri x1 l l A Bottom Glass Bracket PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 ® 10 ST4.
15 14 ©2022 DreamLine® All Rights Reserved Parts List 16 d e e in ex1rv L x1 s m e a R e r s D ght © Ri All ® 135º Strike Vinyl for 10mm (3/8”) glass 17 ST4.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 1 Installation Steps ® ® d e d e e n v e Table A i r n v L i r e L s e m W1 W2 Glass Box Code s e m a e R a e rre ttss R! D h D ig h © g © ll R i R l l A A SHEN-GLP2601-343410 SHEN-GLP2601-363610 SHEN-GLP2601-383810 SHEN-GLP2601-404010 34" 36" 38" 40" W1 NOTE: The Stainless Steel U-Channels (#11) must be installed at the correct dimensions for the model size indicated in Table A.
© 2022 DreamLine® All Rights Reserved 2 W1 d 1 e e in erv L s m e a R e r s D ght © Ri All W2 ® 2 W1 W2 d e e in erv L s m e a R e r Fig 2 s D ght © Ri All ® Parts Needed 11 x2 Tools Needed PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 10
NOTE Install the U-Channels (#11) (on both sides of the opening 1 2* d e v ® W1 W1 © 2022 DreamLine® All Rights Reserved 3 e r n i L e s m e a R e Dr ghts © Ri All 3 W2 4 W2 Fig 3 Parts Needed 11 is present behind the wall: ® *◾Ifdrilla aStud Ø3/16”(4mm) hole up to the stud, NOTE d e v e r n i L e s m e a R e Dr ghts © Ri All drill an Ø1/8” (3mm) pilot hole into the stud and use the ST4.
© 2022 DreamLine® All Rights Reserved 4 d e e in erv L s m e a R e r s D ght © Ri All ® inside inside Fig 4 5 Parts Needed 01 1 d e e in erv L s m e a R e r s D ght © Ri All 2 ® Fig 5 x1 03 x1 12 x2 Tools Needed (Left-hand swing installation shown) PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 12
© 2022 DreamLine® All Rights Reserved 6 ® ved e r n i L e s m e a R e Dr ghts © Ri All 1 2 Fig 6a 1/4” MAX 1/4” MAX 23-15/16” ! d e e The distance between n v i r L e the edges of both s m e stationary panels needs a R e r to be 23-15/16” s D ght 23-15/16” © Ri All ® Parts Needed 01 x1 03 x1 Tools Needed 23-15/16” (Left-hand swing installation shown) PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 Fig 6b 13
© 2022 DreamLine® All Rights Reserved 7 (Overhead View) 1/4” MAX Adjustment in UChannel W2 d e e in erv L s m e a R e r s D ght © Ri All ® W1 1/4” MAX Adjustment in UChannel 23-15/16” d e e in erv L s m e a R e r s D ght © Ri All ® Tools Needed PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 14
© 2022 DreamLine® All Rights Reserved 8 1 NOTE d e e in erv L s m e a R e r s D ght © Ri 2 l l A NOTE Repeat these steps to install the panel glass on the opposite threshold ® 3 d e e in erv L s m e a R e r s D ght © Ri All ® NOTE For installation into an Acrylic threshold: ◾ Drill an Ø1/8”(3mm) hole and use the ST4.0 x 25mm Countersunk Screw (#08). For installation into an Tile threshold ◾ Drill a Ø3/16” (4mm) hole up to the stud, drill an Ø1/8” (3mm) pilot hole into the stud and use the ST4.
© 2022 DreamLine® All Rights Reserved 9 *1 d e e n v i r L e s m e a R e Dr ghts © Ri 2 l Al ® *Fast-drying 100% silicone recommended for the installation of hinge panels. 3 d e e n v i r L e 5 s m e a R e Dr ghts © Ri All screw 4 NOTE washer Repeat these steps to install the panel glass on the opposite threshold. Maintain the required 23-15/16” spacing.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 L-Bar™ Installation ® 10 4.6 4.5 4.8 4.4 4.7 d e e in erv L s m e a R 05 Dre s t h © Rig l l A 4.2 4.3 4.1 Left-handed L-Bar™ Support Bracket shown Fig 10 d e e n v i r L e s m e a sR e r D ght © Ri l l A ® Item 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 Item Description PVC Spacer 0.5 mm M5 Rubber-Tipped Set Screw L-Bar™ Bracket L-Bar™ Bracket Decorative Cover Wall Anchor L-Bar™ Bracket Wall Plate Truss Head Screw ST4.2×40 M5×14.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 11 3 d e e n v i r L e s m e a R e r s D ght © Ri l l A 1 ® 2* 5 6 7 d e e n v i r L e s m e a R e r s D ght © Ri All Fig 11 4 Leave 1/16”-1/8” space between Bracket Wall Plate (#4.6) and U-Channel ® (Left-hand L-Bar™ Support Bracket shown) TIP *Leave the L-Bar™ decorative cover attached when marking the L-Bar™ position on the wall to allow space (1/16”-1/8”) to re-attach the cover plate after installation.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 12 1 d e 3* e n v i r L e s m e a R e Dr ghts © Ri All ® 2 Max 3/16” (4mm) 4* Max 3/16” (4mm) 5 d e e n v i r L e s m e a R e Dr ghts © Ri All ® (Left-hand L-Bar™ Support Bracket shown) * To adjust the angle of the L-Bar™: NOTE Loosen the M5 x 14.5 screws, rotate the appropriate set screw (See Fig 12.3 and 12.4) to adjust the angle of the L-Bar™ (up to 3/16” (4mm)) in the desired direction. Hand tighten the M5 x 14.
© 2022 DreamLine® All Rights Reserved 13 23-15/16” d e e in erv L s m e a R e r s D ght © Ri All ® 23-15/16” Return Panel Glass (#01) Fig 13 (Left-hand swing installation shown) TIP NOTE Before installing the Door glass (#02), attach the 135° Strike Vinyl (#14) to the edge of the Return Panel Glass (#01) to protect the edge of the glass during installation of the Door Glass (#02). Allow the silicone in the U-Channel holding the Hinge Panel Glass (#03) to set before hanging the door glass.
© 2022 DreamLine® All Rights Reserved Glass to Glass Hinges Hinge Installation Procedure (180º and 135º Hinges) Follow these installation instructions after the installation of the Stationary Hinge Panel Glass. The Hinge Panel Glass must be sturdy and secure before installing the hinges and Door Glass. ! 14 d e e n v i r L e s m e a R e r s D ght © Ri l l A 2 Remove the hinge screws, face plates and gaskets from both hinges. Set the thinner (1mm) gaskets aside for the next step.
©2022 DreamLine® All Rights Reserved 16 NOTE NOTE Attach the Glass-to-Glass Hinges to the Stationary Panel Glass with the bolt openings facing the inside of the shower. Be sure the inside edge of the hinges are flush with the edge of the glass. Fig 16 d e e in erv L s m e a R e r s D ght © Ri All Install the vinyl spacers cut earlier from the spare gaskets between the Hinge and the Door Glass in the marked locations. Layer them if needed to fill the gaps.
NOTE © 2022 DreamLine® All Rights Reserved 17 Hanging the Door Glass Use a glass suction cup and a helper to hang the Door Glass (#02). Install the vinyl spacers cut earlier from the thinner/spare 1mm gaskets between the hinge and the Door Glass in the indicated locations. Layer them if needed to fill all the gaps. This will prevent contact between the hinge and the glass and help to keep the Door Glass level.
TIP © 2022 DreamLine® All Rights Reserved 18 Tighten the Hinge screws as firmly as possible with a screw gun. Door Glass Stationary Panel Glass d e e in erv L s m e a R e r s D ght © Ri All ® d e e in erv L s m e a R e r s D ght © Ri All ® Parts Needed 05 Medium-Strength Thread Lock (Not Included) NOTE Install the Caps on all Hinge scews.
© 2022 DreamLine® All Rights Reserved 19 NOTE These adjustable hinges are factory set to overclose for a tight seal and do not need adjustment. However, if an adjustment is required, see Page 30 for instructions regarding the adjustment features of these hinges. d e e in erv L s m e a R e r s t D gh © Ri l l A ® Adjustment Screws Fig 14b 20 Install the Door Handle (#06) Fig 15 d e e in erv L s m e a R e r s D ght © Ri l l outside A ® NOTE The larger knob on the door handle goes on top.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 21 Vinyl Seal Installation 2 d e e in erv L s m e a R e r s D ght © Ri l l A 1 ® 3 Fig 15 d e e n v i r L e s m e a R e r s D ght © Ri All ® Inside NOTE The deflector strip on the Sweep Vinyl must be installed toward the inside of the shower Parts Needed 15 Deflector Strip x1 26 © 2022 DreamLine® All Rights Reserved
© 2022 DreamLine® All Rights Reserved PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 Vinyl Seal Installation (Cont’d.
d e e n v i r L e s m e a R e r s D ght © Ri l l A 1 2 Notch vinyl to fit around back side of hinge Slit soft vinyl flap Slice the soft vinyl flap with a razor knife where the hinge and glass meet hinge panel Notch bottom of vinyl to fit around back side of the hinge door 3 Slice the soft vinyl flap with a razor knife where the hinge and the glass meet Notch top and bottom of vinyl to fit around back of hinge and around the sweep vinyl.
© 2022 DreamLine® All Rights Reserved 24 Surfaces need to be clean and free of debris before applying silicone. Apply to the entire interior perimeter of the panel glass. NOTE d e e in erv L s m e a R e r s D ght © Ri All ® 24 Hours d e e in erv L s m e a R e r s D ght © Ri All ® ! Allow 24 hours for the silicone to cure before using shower.
© 2022 DreamLine® All Rights Reserved 130° Adjustable Hinge Information HG-PRS30A 130° Adjustable Hinge NOTE The hinge assemblies are preset to overclose 5° beyond the normal closing position to create a tight seal against the strike vinyl. While it is not necessary to adjust the hinges, the adjustment feature on the hinge assemblies can be used to change the closing angle of the door only. Make any hinge adjustments prior to installing the Strike Vinyl. Both Hinge ®and to the same angle.
Product Maintenance ©2022 DreamLine® All Rights BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
Problem/Symptom Suggested Solution •Check all shipping/packaging material for missing parts/components. •If not found, contact DreamLine Customer Support (1-866-731-2244) to order factory part replacement. ® Missing Parts d e e n v i r L e s m e a R e Dr ghts © Ri All Water Leaks/Stationary Panels Water Leaks/Door Glass Door Glass does not create a good seal when closed. Door Glass does not open or close smoothly.
PRISM PLUS Shower Enclosure Manual Ver 2 Rev 2 012022 Factory Parts Information d e e n v i r L e s m e a R e r s D ght © Ri l l A SHEN-GLP2601 PRISM PLUS ITEM # 01 02 03 FACTORY PART NUMBER ® FACTORY PARTS INFORMATION ITEM DESCRIPTION QTY 014352028 Return Panel Glass (34" x 34") 1 014352021 Return Panel Glass (36" x 36") 1 014352023 Return Panel Glass (38" x 38") 1 014352025 Return Panel Glass (40" x 40") 1 014352026 Door Glass 1 014352027 Hinge Panel Glass (34" x 34") 1 014352
d e e in erv L s m e a R e r s t D gh © Ri l l A ® d e e in erv L s m e a R e r s t D gh © Ri l l A ® TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.