User Manual

ManualsBrandsDreams ManualsFurnitureJasmine Bedstead Double and King Size

Assembly Instructions

1. We suggest you spend a short time reading through this leaflet and

then follow the simple step by step instructions.

2. If you follow the instructions carefully the end result should be worth

the effort.

3. Do not discard any of the packaging until you have checked that you

have all the parts and the pack of fittings.

4. To ensure an easier assembly, we strongly advise that all fittings are

only finger tightened during initial assembly. Only upon completion

of the assembly should all fixing points be fully tightened.

5. We recommend a periodic check on all fixing points to make sure

they remain fully tightened.

6. Keep glue and fittings out of children's reach.

7. In the unlikely event that this product has missing or damaged parts,

please call 0844 292 0000, followed by selecting Option 4 to obtain

spares.

Before you

start, here

is some

helpful advice

hour

minutes

JASMINE BED

211-01079 (DOUBLE-WHITE)

211-01081 (DOUBLE-BLACK)

211-01080 (DOUBLE-PINK)

215-00994 (KING-WHITE)

215-00996 (KING-BLACK)

215-00995 (KING-PINK)

Minimum No.of people

recommended to assemble

this product:

Approx assembly time:

Page 1 of 4

KING

DOUBLE

Summary of content (4 pages)

PAGE 1
211-01079 211-01081 211-01080 215-00994 215-00996 215-00995 JASMINE BED (DOUBLE-WHITE) (DOUBLE-BLACK) (DOUBLE-PINK) (KING-WHITE) (KING-BLACK) (KING-PINK) Assembly Instructions KING 2 Minimum No.of people recommended to assemble this product: Approx assembly time: 45 hour DOUBLE minutes Before you start, here is some helpful advice 1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. 2.
PAGE 2
Fittings Parts A M6x13mm Allen screw 4pcs B M6x25mm Allen screw 8pcs C M6x40mm Allen screw D Part 9 Donble(13pcs) King (14pcs） Washer-Ø16 Part 10 Double(26pcs) King (28pcs) (INCLUDES PRE-ASSEMBLED PLASTIC CAPS) Part 8 Double(26pcs) King (28pcs) (PRE-ASSEMBLED ONTO SLATS) 4pcs Part 6 16pcs E Rubber washer 8pcs F Nut 4pcs G Part 6 Part 1 Allen key 2pcs H M6x25mm Short stud Part 3 Part 4 2pcs Part 6 Part 5 Part 7 Part 3 Part 6 Part 7 Part 2 Part 4 Page 2 of 4
PAGE 3
Assembly 1) Assemble side rails 3 in between headboard 1 and footboard 2 using fixings B D and E . STEP 1 1 3 2 G E D 1) Assemble end support 4 to the underside of side rails 3 using fixings A D and F . B A D 3 STEP 2 Repeat for both ends. 4 2) Screw short studs H into the underside of central support 5 . F 4 Screw support legs 7 onto the short studs and tighten . 5 5 3) Assemble central support 5 in between end supports 4 using fixings C and D .
PAGE 4
1) Fit wooden slats 10 into the side rails 3 as shown. STEP 3 10 Note：Plastic caps 8 are already pre-assembled onto one end of wood slats 10 . 3 2) Fit wooden slats 10 into both side of plastic cap 9 ， before pushing cap 9 into central support 5 . 10 9 10 5 1) Fit finials 6 to headboard and footboard.