Warranty

2
!,(+(5+<5+,9:;(5+(3305:;9<*;065:. Failure to follow all instructions listed
below, may result in electric shock, fire and/or serious personal injury.
"%#""#!$#"
!
WARNING
63+ ;663 )@ 05:<3(;,+ .907705. :<9-(*,:
>/,5 7,9-69405. (5 67,9(;065 >/,9, ;/,
*<;;05.;663 4(@ *65;(*; /0++,5>0905. 69
0;:6>5*69+ Contact with a “live” wire will
make exposed metal parts of the tool “live” and
shock the operator. If cutting into existing walls
or other blind areas where electrical wiring
may exist is unavoidable, disconnect all fuses
or circuit breakers feeding this worksite.
3>(@:4(2,:<9,;/,>692:<9-(*,0:-9,,
-964 5(03: (5+ 6;/,9 -69,0.5 6)1,*;:
Cutting into a nail can cause the bit and the
tool to jump and damage the bit.
,=,9/63+;/,>69270,*,0565,/(5+(5+
;/, ;663 05 ;/, 6;/,9 /(5+ >/,5 05 <:,
,=,9 73(*, /(5+: 5,(9 69 ),36> *<;;05.
:<9-(*, Clamping the material and guiding
the tool with both hands is safer.
,=,9 73(*, ;663 >0;/ )0; 796;9<+05.
;/96<./ )(:, 65 ;67 6- ),5*/ 69 >692
:<9-(*,(@;/,;663650;::0+,699,;9(*;
;/,)0;),-69,:,;;05.65),5*/69>692:<9
-(*, Protruding cutting bit may cause tool to
jump.
3>(@: >,(9 :(-,;@ .6..3,: (5+ +<:;
4(:2  $:, 653@ 05 >,33 =,5;03(;,+ (9,(
Using personal safety devices and working in
safe environment reduces risk of injury.
-;,9 */(5.05. ;/, )0;: 69 4(205. (5@
(+1<:;4,5;:4(2,:<9,;/,*633,;5<;(5+
(5@6;/,9(+1<:;4,5;+,=0*,:(9,:,*<9,3@
;0./;,5,+ Loose adjustment device can
unexpectedly shift, causing loss of control.
Loose rotating components will be violently
thrown.
,=,9:;(9;;/,;663>/,5;/,)0;0:,5.(.,+
05;/,4(;,90(3 The bit cutting edge may grab
the material causing loss of control of the
cutter.
3>(@:/63+;/,;663>0;/;>6/(5+:+<905.
:;(9;<7The reaction torque of the motor can
cause the tool to twist.
#/, +09,*;065 6- -,,+05. ;/, )0; 05;6 ;/,
4(;,90(30:=,9@04769;(5;(5+0;9,3(;,:;6
;/,+09,*;0656-)0;96;(;065&/,5=0,>05.
;/,;663-964;/,;67;/,)0;96;(;,:*36*2
>0:,  ,,+ +09,*;065 6- *<;;05. 4<:; ),
*6<5;,9*36*2>0:,NOTE: Inside and outside
cuts will require different feed direction. Refer
to section on feeding the router. Feeding the
tool in the wrong direction causes the cutting
edge of the bit to climb out of the workpiece
and pull the tool in the direction of the feed.
3>(@: <:, ;/, ;663 >0;/ ;/, 96<;,9 )(:,
:,*<9,3@ (;;(*/,+ (5+ 76:0;065,+ -3(;
(.(05:;4(;,90(3),05.*<;Having the base
securely positioned on the material improves
the stability and control of your tool.
,=,9<:,+<3369+(4(.,+)0;:"/(97)0;:
4<:;),/(5+3,+>0;/ *(9, Damaged bits
can snap during use. Dull bits require more
force to push the tool, possibly causing the bit
to break.
,=,9;6<*/;/,)0;+<905.69044,+0(;,3@
(-;,9<:, After use, the bit is too hot to be
touched by bare hands.
,=,93(@;/,;663+6>5<5;03;/,46;69/(:
*64,;6*6473,;,:;67 The spinning bit can
grab the surface and pull the tool out of your
control.
6 56; <:, ;/, ;663 -69 +903305. 7<976:,:
This tool is not intended to be used with drill
bits.
,=,9<:,)0;:;/(;/(=,(*<;;05.+0(4,;,9
.9,(;,9;/(5;/,67,505.05;/,)(:,
(2,:<9,;69,(+(5+<5+,9:;(5+;/,>5,9A:(5<(3-69@6<99,4,3!6;(9@#663
;;(*/4,5;-69<:,>0;/9,4,3!6;(9@#6636+,3:

6>,9#663"(-,;@!<3,:
"(-,;@!<3,:-69!6<;,9:
DM 2610920458 05-12_DM 2610920458 08-10 5/14/12 11:18 AM Page 2