User Manual

Filament
Guide
PRESS
LIFT
IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
For English Version Version française Versión en español
See page 2 Voir page 37 Ver la página 73
Operating/Safety Instructions
Consignes de sécurité/d’utilisation
Instrucciones de funcionamiento y seguridad
1-844-4DRML3D (1-844-437-6533) www.dremel.com
Call Toll Free for
Consumer Information
& Service Locations
Pour obtenir des informations
et les adresses de nos centres
de service après-vente,
appelez ce numéro gratuit
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
P.O. Box 081126 Racine, WI 53408-1126
3D20
Idea Builder
3D20 Quick Start Guide
WARNINGWARNING
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
0
.
3
m
m
C
L
E
A
R
A
N
C
E
LEVELING SHEET
TURN LEFT TO RAISE
THE BUILD PLATFORM
TURN RIGHT TO LOWER
Adjust the platform until
leveling tool slides between
the extruder and platform
with some resistance
0.3mm
LEVELING TOOL
3D20 Quick Start Guide
Unboxing
1
Getting to Know Your Dremel 3D20
3
Getting Ready to Build
4
1. Lid
2. Door
3. Touch Screen
4. Build Platform
5. Build Platform Clips
6. Filament Spool
7. Filament Spool Holder/Lock
8. Extruder Tip
9. Extruder Fan
10. Extruder
11. Extruder Intake
12. X-Axis Guide Rails
13. Stepper Motor (1 of 3)
14. Z-Axis Guide Rail
15. Filament Guide Tube
16. Y-Axis Guide Rails
17. SD Card Input
18. USB Input
19. Power Switch
20. Power Input
FILAMENT INSTALLATION
1. Ensure the power switch is in the off position, remove the lid
and remove the build platform.
2. Place filament spool onto spool holder with spool being fed from
the bottom towards the back of the Dremel 3D20. Insert spool
lock into spool holder and rotate 90 degrees to lock in place.
3. Thread filament through filament guide tube.
4. Insert the filament coming from the filament guide tube into
the extruder intake (top).
5. Adhere build tape over the build platform.
6. Install platform using 3 clips. Place the table under the two
back clips then snap it in with the front clip.
7. Plug power cord into outlet and turn on power switch.
8. Tap “Tools” on your Dremel 3D20’s touch screen, then tap
“Filament”, then tap “Load Filament” and wait for the extruder
to heat.
9. Once heated, filament will be drawn through the extruder. Allow
filament to exit the extruder for 10 seconds before tapping the
return arrow to complete.
Kit Contents
2
TIP: Save your Dremel 3D20 packaging for future transportation
and storage.
Firmly lift the build platform
to the top position
Dremel 3D20 Instruction Manual Quick Start Guide 1 Filament Spool
Power CableSpool Lock USB Cable SD Card
Build Tape Object Removal Tool Unclog Tool Leveling Sheet
WARNINGWARNING
READ ALL OPERATING/SAFETY INSTRUCTIONS IN THE MANUAL AND FAMILIARIZE YOURSELF WITH THE
DREMEL 3D20 BEFORE SETUP AND USE. FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS
MAY RESULT IN FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY.
1
2
3
4
5
6
7
8
9 1011 12
13
14
15
16
17 18
19 20
WARNINGWARNING
OBSERVE ALL PROVIDED WARNINGS AND SAFETY
INSTRUCTIONS WHEN USING THE DREMEL 3D20.
FAILURE TO DO SO MAY RESULT IN FIRE, EQUIPMENT DAMAGE,
PROPERTY DAMAGE OR PERSONAL INJURY.
2
3
5
1
8
4
1
2
3
4
5
6
ENGLISH
SIDE 1