User manual

21
SAFETY WARNINGS SPECIFIC TO
GRINDING AND ABRASIVE CUTTING-OFF
OPERATIONS
a. Use only wheel types that are recommended for

for the selected wheel. Wheels for which the power
tool was not designed cannot be adequately guarded
and are unsafe.
b. Wheels must be used only for recommended

side of cut-off wheel.Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
 
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
 
tools. Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and may
burst.
ADDITIONAL SAFETY WARNINGS
SPECIFIC TO ABRASIVE CUTTING
OFFOPERATIONS
a. Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut.Overstressing the wheel increases the
loading and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback or wheel
breakage.
b. Do not position your body in line with and behind
When the wheel, at the point of
operation, is moving away from your body, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
 
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
off wheel from the cut while the wheel is in motion
otherwise kickback may occur.Investigate and take
corrective action to eliminate the cause of wheel binding.
 
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
e. Support panels or any oversized workpiece to

Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
 
The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
SAFETY WARNINGS SPECIFIC TO
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the


the brush. The wire bristles can easily penetrate light
clothing and/or skin.
 

Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.
 
brushes.
ENVIRONMENT
DISPOSAL


ONLY FOR EC COUNTRIES







SPECIFICATIONS
GENERAL SPECIFICATIONS
  
  
  
  

  


EXTENSION CORDS


ASSEMBLY



GENERAL






 
 
 
 
 
 
 
 
 
 
k. Never lay the power tool down until the accessory
has come to a complete stop.The spinning
accessory may grab the surface and pull the power
tool out of your control.
 
side.Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
 The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
 
materials. Sparks could ignite these materials.
 
coolants.Using water or other liquid coolants may
result in electrocution or shock.
 
paper. Follow manufacturers recommendations,
Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing of
the disc or kickback.
 


Loose and spinning attachment strings can entangle
your ngers or snag on the workpiece.
KICKBACK AND RELATED WARNINGS

















 
position your body and arm to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
The operator can
control torque reactions or kickback forces, if proper
precautions are taken.
 
Accessory may kickback over your hand.
c. Do not position your body in the area where the
power tool will move if kickback occurs.Kickback
will propel the tool in direction opposite to the wheel’s
movement at the point of snagging.
 

accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
 
or toothed saw blade. Such blades create frequent
kickback and loss of control.