User Manual
Table Of Contents
- SAFETY INSTRUCTIONS
- BEFORE YOU BEGIN
- CONTROLS AND OPERATING INSTRUCTIONS
- Set unit upright
- Positioning a Dehumidifier
- Extend handle
- Set up drain hose
- NOTICE: Uncoil and straighten the entire drain hose. Do not leave any part of the hose coiled on the unit and do not place the end of the hose higher than 20 ft. (6 m) above the bottom of the unit. Also check for kinks or other obstructions that might...
- Plug in electrical cord
- HOW TO USE THE CONTROL PANEL
- Home Screen Views
- AT THE END OF THE JOB
- TRANSPORTATION AND STORAGE
- MAINTENANCE SCHEDULE
- Before each use
- Monthly
- As Needed
- Clean Pump Check Valve and Basin. This requires removal of the front housing.
- Fig. B: Disassembly for Cleaning
- TROUBLESHOOTING
- INSTRUCCIONES DE SEGURIDAD
- ANTES DE COMENZAR
- CONTROLES E INSTRUCCIONES DE OPERACIÓN
- Coloque la unidad en posición vertical
- Dónde colocar el deshumidificador
- Extienda el mango
- Instale la manguera de drenaje
- AVISO: Desenrolle y enderece toda la manguera de drenaje. No deje ninguna parte de la manguera enrollada en la unidad y no coloque el extremo de la manguera a más de 20 pies (6 m) por encima de la parte inferior de la unidad. Compruebe también que no ...
- Enchufe el cable eléctrico
- CÓMO USAR EL PANEL DE CONTROL
- Visualizaciones de la pantalla principal
- AL FINAL DE TRABAJO
- TRANSPORTE Y ALMACENAMIENTO
- PLAN DE MANTENIMIENTO
- Antes de cada uso
- Mensual
- Según sea necesario
- Limpie la válvula de retención de la bomba y el recipiente: Esto exige la extracción de la carcasa del frente.
- Fig. B: Desensamble para la limpieza
- RESOLUCIÓN DE PROBLEMAS
- INSTRUCTIONS DE SÉCURITÉ
- AVANT DE COMMENCER
- COMMANDES ET INSTRUCTIONS DE FONCTIONNEMENT
- Mettez l’unité debout en position verticale.
- Positionner un déshumidificateur
- Poignée d’extension
- Mise en place du tuyau de vidange
- Cet appareil pompe de l’eau automatiquement sur une base régulière. Ce déshumidificateur est équipé d’un raccord à connexion rapide pour l’attachement au tuyau de vidange fourni (12 m - 40 ft), situé sur le plateau sur le dessus de l’unité. Déballez l...
- NOTICE : Déroulez et redressez le tuyau de vidange entier. Ne laissez aucune partie du tuyau enroulée sur l’unité et ne placez pas l’extrémité du tuyau à une hauteur de plus de 6 m (20 ft), à partir du bas de l’unité. Vérifiez aussi qu’il n’y ait pas ...
- Brancher le câble électrique
- Affichages écran d’accueil
- À LA FIN DE LA TÂCHE
- TRANSPORT ET RANGEMENT
- PROGRAMME DE MAINTENANCE
- Avant chaque utilisation
- Tous les mois
- Si nécessaire
- Nettoyer le clapet antiretour de la pompe et le bac Cela nécessite le retrait du logement avant.
- Fig. B : Démontage pour le nettoyage
- DÉPANNAGE
108259F #103614 (F600) 4 Legend Brands, Inc.
ERRORS AND WARNINGS
If the control system detects a problem, it will display an "Alert" symbol in the upper right corner of the screen. Press
ON/OFF to view the message and OK to clear the message. NOTE: In the case of an error, the unit will not operate until
the problem is resolved. Refer to the explanations and solutions shown below. If these solutions do not fix the problem,
contact your local authorized service center for further assistance.
CONTROL PANEL
MESSAGE
EXPLANATION AND SOLUTION
ER4 Error
Defrost Thermistor Connect
—or—
ER4 Error
Outlet Thermistor Connect
Temp sensor is open, missing, or shorted. Check that temp sensors are
installed correctly on control panel. If error persists, contact service.
ER5 Error
Inlet RH1 Temp/RH Sensor
Inlet Temp/RH sensor is open, missing, or shorted. Check that inlet
temp/RH sensor is installed correctly on control panel and inlet shroud. If
error persists, contact service.
ER6 Error
Current Sensor Failure
Current sensor failure. If error persists, contact service.
ER9 Error
Pump Blocked
Check for obstructions in drain hose. Check the pump.
W1
Low BATTERY
Replace coin cell battery (3V, CR2032) on control panel.
W2
BLE Error
W3
Flash Reset
W4
WDT Reset
Cycle power to dehumidifier. If warning persists, contact service.
AT THE END OF THE JOB
To reduce the possibility of drips when moving the
unit, follow these additional steps to ensure that all
water is removed from the unit.
NOTICE: The unit will complete the defrost cycle even if
the unit is turned off but still plugged in. If the unit is
unplugged during the defrost cycle, excessive water may
accumulate in the unit and may drip out when you move
the unit.
NOTICE: To ensure the condensate tank empties
completely while purging, make sure the unit is placed
upright on a horizontal surface.
1. Do not turn unit off or move it until it has returned
to normal operating mode.
2. Gently rock the machine to ensure any water
remaining on interior surfaces falls into the sump
area.
3. Press the PURGE key. When the purge cycle is
complete, turn the unit off.
4. Remove the external drain hose, drain it carefully,
coil it and return it to the storage tray on the top of
the unit.
TRANSPORTATION AND STORAGE
IMPORTANT: Before moving, transporting or
storing, purge unit and stow hose and power cord as
described in the “At the End of the Job” section
above.
NOTICE: Handle the unit carefully. Do not drop, throw or
place the unit where it could fall. Rough treatment can
damage the dehumidifier and may create a hazardous
condition or void the warranty.
• Do not expose the control panel to moisture, snow
or rain.