OPERATING INSTRUCTIONS & DRILL INFORMATION MODEL 750SP CONTENTS US Patents D385567, & 4,471,581 5,735,732 & 5,400,546 other Patents Pending Warranty Congratulations Quick Steps Instructions Maintenance Quick Facts Replacement Parts Troubleshooting 1 2 3 4 7 8 9 10
US DEPARTMENT OF LABOR Form Approved Occupational Safety and Health Administration OMB No.
You have just purchased the finest, most accurate and best engineered drill bit sharpener ever created for home and professional use. It is likely that your experience with this sharpener will be unlike any sharpener you have used before. We hope that in the next several minutes you will discover how Professional Tool Manufacturing LLC and the Drill Doctor® help to SIMPLY improve the quality of your life (and your drill bits’ too!).
QUICK STEPS QUICK OPERATING STEPS A-1 Models 500SP & 750SP A. Setting for split point style (full instructions page 4) 1. Determine the point angle of your drill by placing the drill point in the point angle gauges. See A-1 A-2 2. Insert a chuck (without drill) into the sharpening tube and pull the loop handle out. Move point angle indicator to the setting needed (118° or 135°). Make sure the loop seats properly. See A-2 3.
INSTRUCTIONS DRILL DOCTOR® INSTRUCTION MANUAL Fig. 2 If possible, the first couple of drill bits you sharpen should be about 3/8" in diameter, or large enough to see how the point looks. Study Figure 1 on page 2 and the Figures 26 and 27 on page 8. Various Drill Doctor® and drill bit parts will be referenced in the following sections. Angle Gauges Step 1: Drill Identification and Sharpener Set Up A. Place the drill in the point angle gauge (see Figure 2).
INSTRUCTIONS STEP 2: Aligning Drill Bit For Sharpening (continued) E. Look into the opening in front of the paddle. Note the location of the two spring steel pawls. Rotate the drill bit until the pawls slip in and grab the flutes at the narrowest point. Continue to push the drill bit against the drill stop (see Figure 9). F. With the drill point against the drill stop and the pawls in their correct position, tighten the chuck by turning the chuck knob CW with the other hand.
INSTRUCTIONS STEP 4: Splitting The Drill Point Fig. 14 You can split either a 118° or 135° drill point. Refer to Figure 31 on page 10 for a drawing and definition of a properly split drill bit point. A. After sharpening the drill point, do not remove the drill bit from the chuck. Align the flats on the chuck with flats in the splitting tube and insert to the point where the flats are touching (See Figure 14). B.
MAINTENANCE DRILL DOCTOR® MAINTENANCE Fig. 21 After sharpening many drill bits, the drill bit grinding dust will accumulate in the grinding compartment. Grinding particles will promote wear in the three tubes and chucks, so cleaning on a consistent basis can add life to your machine. Before any maintenance or cleaning is performed, be sure to unplug your Drill Doctor®. Chuck Grooves Cleaning The Drill Doctor ® Unplug the Drill Doctor®.
QUICK FACTS Quick Facts About Drill Bits Fig. 25 118° 118° STANDARD POINT: This drill bit point angle is considered a standard general purpose geometry . It is used for drilling soft or mild materials such as cold rolled steel, aluminum, and wood. Typically the standard drill bit is made of High Speed Steel (HSS). The tip of the drill bit can easily be split making it a High Performance drill bit.
" - 3/ 4 " 3/3 9 MM Hub Wrench 3/32" to 1/2" Chuck part # PPO1460SF # PPO1500PA partpart #SA01500PA MM 1/ 2 - 1 /2 " 2" 13 - 1 User Replacable Parts 2 .5 - 1 3 REPLACEMENT PARTS Fig.
You can take less material off of a drill bit. The sharpener will remove approximately .015” to .025” depending upon the point angle that is sharpened. To align the drill bit to remove less material, merely insert a shim or feeler gauge between the drill bit point and the metal stop where the drill bit normally touches during alignment. TROUBLESHOOTING 1. I aligned the drill bit and sharpened it, but no material gets removed. You may have allowed the paddle to knock the drill back into the chuck.
Dear Customer, We appreciate the confidence you have placed in us by purchasing the Drill Doctor ® and we want you to be as excited about this remarkable tool as we are. It’s easy to use correctly, if you follow the instructions. We have created this manual and video in order to give you the information you need to effectively master its operation and get the satisfactory results you expect from Professional Tool Manufacturing LLC. MODEL 500SP 3/32” - 1/2” CHUCK 1/2” DIAMOND WHEEL 110V 60Hz 1.
