000 SERIES DP1000(B) OWNER� MANUAL Please read this manual carefully prior to operating your Drinkpod. Retain for future reference.
Temperature Please use the product in a dry place within the temperature ranges of 40 ° and 100 °. Electrocution Prevention Safety caution & usage Troubleshooting Should your appliance ever fail, please disconnect the power and water immediately before calling for assistance. Maintenance To avoid leakage and damage, never remove appliance parts. Child Supervision Unsupervised children should not be allowed to operate the machine.
6 Water Filtration System 7 Setup & Getting Started Table of Contents 17 Removing/Replacing Filters 1 Safety, Caution, & Usage 21 Indicator Lights 3 What’s Included 22 Filter Cycles 5 Features & Specifications 23 Maintenance Notes 20 Flushing Filters 2
P What's X included A W I N aa Y J z v K u Q R b l s t BOTTOM P H M CC C d bb DD o K f g o e 3
A 25’ Industrial Grade PVC Tubing b 3/4” x 3/4” x 1/4” Steel Union Adapter C 1/4” PVC Shutoff Valve d S Cold Water Selector T Dispense Water Button Flush Connector u Quck Fill Mode Selector (10 Seconds) e Service & Support Letter V Condenser Active Status Light f Quickstart Guide W Heater Active Status Light g Feedback Request Letter X Eco Mode Active Status Light H Pod Filter Magnetic Door Y UV Light Filter Active Status Light I Cooling Mode Switch z Pod Filter Status Light
Features Model DP1000(B) Rated Power 555 Watts Heating Power 420 Watts Cooling Current 2.0 A Hot Water Production & Storage Rate: 1.01 gal/hr (4 L/h) ≥ 185° F (85° C) Storage: 0.24 gal (0.9 liter) Cold Water Production & Storage Rate: 0.79 gal/hr (3 L/h) ≤ 50° F (≤ 10° C) Storage: 0.34 gal (1.3 liters) Environmental Requirements Temperature: 40 ° F - 100 ° F (4° C - 38° C) Humidity: ≤ 90% Water Pressure Requirements 14.5 psi - 58psi (0.1 MPa - 0.
water Filter system UF Inline & Purification Flowchart 6
What You’ll Need: • 1x Nearby Waterline Optimally a kitchen sink. • 1x Pair Of Pliers Setup & Getting Started • 1x Drill & Drill Bit If you’ll need/want to create a more direct route for your Drinkpod’s water source line). • 1x Sick Beat (song)* Recommended for jamming along with, to ensure best installation experience. * Country music should be avoided if possible, and only utilized with extreme caution.
C A Step 2 b Unpack product. Remove accessories & papers and set aside. Remove Drinkpod, and place on ground.
Step 3 Insert R drip tray & collector into the slot underneath the dispensers. When choosing where to place the appliance, ensure there is 4” of clearance on the right & back sides to allow for airflow. R 9 Read Before Proceeding Unlike most of our competitors, we’ve upgraded our installation kit to include a premium b Steel Union Adapter, rather than the traditional selfpiercing saddle joint.
Step 4 Gather pliers, A 25’ PVC tubing, b brass tee union adapter, and drill + drill bit (if hole is required and unavailable to connect watersource to Drinkpod). Step 5 Identify cold water line source.
Step 6 Twist cold water source valve clock-wise to turn off. Step 7 Unscrew (counterclockwise) kitchen sink faucet hose from cold water shutoff valve. Use pliers carefully if required to loosen tight connection.
Step 8 Screw b union adapter (clockwise) down onto cold water shutoff valve. Do not tighten with pliers more than 1/4 turn. 8 9 Step 10 Screw kitchen sink faucet hose (we unscrewed in step 7) onto the top of b union adapter (clockwise) . Do not tighten with pliers more than 1/4 turn. Step 9 Ensure b union adapter is closed.
Step 11 Unscrew compression nut from b quick connect adapter. Step 12 Thread A 25’ x 1/4” PVC tubing through b quick connect adapter’s compression nut.
Step 13 Firmly slide A 25’ x 1/4” PVC tubing over b quick connect adapter up to (but not overlapping) the threads. Step 14 Firmly screw the compression nut back on to b quick connect adapter. Do not tighten with pliers more than 1/2 turn.
Before You Continue Step 15 In our next steps, we will connect and setup your new Drinkpod. Before proceeding, please ensure that A 25’ x 1/4” PVC can reach from your water source to the Drinkpod. Ensure Drinkpod is located where you plan to use it, and that A 25’ x 1/4” PVC tubing has been laid so that it reaches M Water Inlet with at least several feet of slack. Should this require drilling holes along the path, please proceed with caution, and at your own risk.
Step 17 Step 16 Connect one end of new tubing section, into one end of C 1/4” Shutoff Valve, and free end of A 25’ x 1/4” PVC tubing, into the other end. Firmly push the tubing into the push-fitting until you cannot push it any further. Some resistance is normal. Use scissors or knie to cut approximately 1’ section off the end of A 25’ x 1/4” PVC tubing at a 90° angle. Step 18 Firmly pull outward on both ends of tubing, to extend quickgripping seals on shutoff valve. Ensure valve is closed.
Removing & Replacing Filters Step 19 Step 21 Open Y Drinkpod Cabinet Door to ensure Filters N , o , P , and Q are properly mounted. Firmly push the open end of new short tubing into M Cold Water Inlet, on the back of your Drinkpod until you cannot push it any further. STOP!!! Step 20 Firmly pull outward on new short tubing section to engage quick-gripping seals.
Step 22 To Remove: 1. Pull back filter pod. 2. Twist counter clockwise. 3. Gently pull filter out/down. Step 24 Step 23 To Replace: Open C 1/4” Shutoff Valve by twisting clockwise. 1. Gently insert filter upwards. 2. Twist clockwise. 3. Gently push filter back in/up.
Step 25 Open b quick connect adapter. Step 26 Open cold water source line.
Always Flush New Pre & Post Carbon Filters Prior To Use Step 28 Step 27 Plug in. Outlet should always be grounded. You must flush the ULTRA + 3 pod filter until it discharges clean water, to ensure any loose particulates are removed prior to using. This will take about 10 minutes. See page 25 for alternative method to extend filter life.
Indicator & STATUS Lights 21
Filter CYCLES Filters can be ordered from our website at drinkpodusa.com, Amazon, Ebay, and other online retailers. The times below are for reference only. Data is based on 2.5 Gallons / 10 Liters usage per day. The actual lifespan of filters varies based on local water quality, and usage. ALWAYS USE 6-9 MONTHS 100hrs* LIFETIME * 100 hours of actual use, which only occurs when water is being dispensed. It is recommended that should this filter require replacement, it be done by a trained professional.
Additional MAINTENANCE NOTES • Rear of appliance should be at least 9” / 12 cm away from the wall it backs up to. • Never put appliance on paper or foam, which could retain water, and lead to creepage. • Never use appliance outdoors, or somewhere it could be splashed by water. 23 • Never place anything flammable next to the machine. • Remember to shut down heating and cooling mods, if appliance will go extended time without use.
• Never use chemical solvents like gasoline to clean appliance. Only clean with tap water and soft cloth. • Every Drinkpod comes with a limited 12 month warranty from the date of purchase. • Never pull the power plug from wall socket prior to turning off machine’s power switch. • Never modify power cord. • If power cord ever becomes damaged, cord should only be replaced by qualified technician. • The tap water is the intended water source for this appliance.
Aternative Flushing Method To extend your filters lifespan, you can follow the steps below as an alternative flushing method. This method is specifically for the pod filter. When using this method, filters should be flushed with H for an additional 10 minutes after they discharge clean water, to ensure any loose particulates are removed prior to using.
Copyright © Drinkpod, LLC. All rights reserved. The Drinkpod brand and logo are trademarks of Drinkpod, LLC.
R K O