Data Sheet

ManualsBrandsDrive System Europe by MSW ManualsAutomationLinear actuator DSZY1Q-24-30-100-STD-IP65 Stroke length 100 mm Thrust 800 N 24 V DC

Linear actuator DSZY1Q-STD

(standard)

The electric linear actuators of the DSZY1Q series are especially

characterized by their smooth running and low noise level. They are

available in three models:

1. DSZY1Q-STD

(standard for all applications without position feedback)

2. DSZY1Q-POT

(with potentiometer for absolute position feedback)

3. DSZY1Q-HS2

(with 2-channel hall sensor for incremental position feedback)

Equipped with a trapezoidal screw spindle (ACME screw), these are

small, compact and lightweight DC linear drives. By means of an

integrated diode circuit, the direction is reversed quickly by simple voltage

reversal of the DC motor. As a standard, all DSZY1Q types have two

integrated, non-adjustable limit switches directly connected to the DC

motor. Overloading of the drive can be prevented by separate monitoring

and limiting of the current.

Type code (all options can be combined)

Optional

DSZY1Q

- 12 - 10 - 200 -

STD

- IP65 - C 1 1

Type Input

voltage

12 V

24 V

Reduction

ratio i

Stroke

25 mm

50 mm

100 mm

150 mm

200 mm

250 mm

300

Model

Standard

IP-

level

Front-

connector

(piston rod)

1 = standard

3 = univeral

6 = plastic

Rear-

connector

(gear cover)

1 = standard

3 = rotated 90°

Performance data: Load – Speed – Current

Reduction

ratio i

Dynamic

Load

(N)

Static

load

(N)

Typical speed *

(mm/s)

Typical current *

(A)

minimum

load

maximum

load

minimum load maximum load

12 V 24 V 12 V 24 V

20 500 2.500 5.8 3.9 0.2 0.1 1.0 0.5

30 800 2.500 3.8 2.6 0.2 0.1 1.2 0.6

Load – Speed – Diagram * Load – Current – Diagram *

(*) Average values

Summary of content (4 pages)

PAGE 1
Linear actuator DSZY1Q-STD (standard) The electric linear actuators of the DSZY1Q series are especially characterized by their smooth running and low noise level. They are available in three models: 1. DSZY1Q-STD (standard for all applications without position feedback) DSZY1Q-POT (with potentiometer for absolute position feedback) DSZY1Q-HS2 (with 2-channel hall sensor for incremental position feedback) 2. 3.
PAGE 2
Additional technical specifications • • • • • Operating voltage 12 V and 24 V Thrust and tensile force up to 800 N Static force 2,500 N Noise level: ≤ 55 dB Duty cycle 25 % (e.g.
PAGE 3
Front and rear connector Front connector (piston rod) 1 = standard 3 6 D=8mm - H=15mm - W=6mm Rear connector (gear cover) 1 = standard 3 D=8mm CAUTION: C11 is standard and will not be specified in the type code. If at least one connector is changed, option C must be attached to the type key (e.g.
PAGE 4
Mounting material Mounting Clamp DSZY1-H01 Mounting Bracket DSZY1-H02 Installation instructions It must be ensured that the load is not greater than shown in the diagram. To protect against overload, the voltage must be switched off when the maximum rated current is reached. This can be read in the force-current diagram depending on the selected reduction ratio. Please note the correct supply voltage, which is indicated on the electric linear actuator.