Table of contents Tabulation Product description Scope . . For your own safety. important information . . Motes conceding the storage smarmy, battery charger and hand control . . important safety rules. . Notes conceding Electromagnetic Compatibility (EMC) Installation and use Unpacking . . First installation in the bath .. Attaching and removing the covers. . installing the headrest {optional} Hand control Operating the Bratislava in the bath . Removing the luff from the bath Maintenance and care. ..
Bella vita — Product description Thank you for deciding to buy a product made by Drive Medical. From now on, this lightweight, high-quality bath lift will make it a ot easier for you to get in and out of your bath. This bathing conforms fo the legal standards DiN EN 18O 10535:2006 and DIN EN The Bella vita is bully with high-quality, recyclable lightweight plastic. This makes our product says to transport and stow away — and ideally sifted for use in the home or away.
For your own safety ATTENTION VITAL INFORMATION! Fully read the Instructions In this manual prior 1o use. Failures 1o do so may result In damage and/or Injury. B important information * Aver use the Bella vita 1o climb in or out of the bath. Never use it as a stand, lifting device, ladder, support, or for any similar purposes outside of the bath. The lift is to be used only in order o take 2 bath.
For your own safety if the device Is not used for long peddler of Hume, the battery should be re-charged every 3 months In order {o Increase the longevity of the devise. = Do not insert any conductive objects (e.g. neediest, metal pins, to) inch the jack socket of the hand control. = Always disconnect the mains plug from the socket before cleaning the battery charger. = (lean the battery charger with a dry cloth only.
For your own safety © Notes concerning Electromagnetic Compatibility (EMC) This product is compliant with the protection requirements set forth in the Council Directive for the Harmonization of Legal Stipulations of the Member States conceding Electromagnetic Compatibility (EMV, IEC 80601-1-2) (89/336/ GEWGAW.
Installation and use [ First installation in the bath 1. Attach the suction cups to the underside of the seat unit (breastplate. The tongues of the rear suction caps must be directed outwards — this ensures better access when the lift has to be removed from the bath. Press the tongues of the front suction cups int the provided recesses {front} in the base plate. Important note: The suction cups held the bathing firmly in place on the bottom of the bath.
Installation and use 4. Now insert the drive unit with integrated back. Now hold the backrest at the hand grips and rest into the bearing blocks of the seat unit using the other hand it it backwards {see {see illustration). illustration) until the drive unit rests against the base plate. O Hand grip Attention! It is very important that both guide pins ars inserted into the bearing blocks! @ Bearing block + @ Guide pin Please make sure that the red stop reversible the correct position. & .
Installation and use €. Connect the hand control to the bath lift. To do this, plug the jack socket onto the j Jack plug until it catches In and the red ring st the {ack Iz unseen. The bathing is now ready for movement. Note: if there Is a risk of the backrest colliding with the back of the bath, repetition the base further away from the end of the bath. 7. Marks sure that the lifting rod is positioned correctly in the unlock ramp.
Installation and use 3 Attaching and removing the covers +To attach the cover, place # correct on the The covers can be attached and removed very surface of the backspin and pres the easily buttons completely into the holes provided in the backrest and seat {or seal and side flaps see illustration. Wackest cover Backrest cover Seat cover (comfort cover shown) Seat cover + To remove the covers, lift the two fastening but The bathing can also be used without covers. tons with two fingers; then pull them out.
Installation and use installing the headrest {optional} Insert the two rods of the headrest into the openings at the top of the backrest pale. The headrest can be effortlessly adjusted to the desired height.
Installation and use [ Hand control Depending on the weight of the person bathing, the capacity of the fully charged battery is for a maximum of 6 baths. During the bathing process the green control lamp of the hand control is it up green. When the charging level of the battery falls to a factory-defined level, the lamp color changes to orange and the lamps stairs to blink slowly.
Installation and use Operating the Bella vita in the bath . Before using your bathing, make sirs tha! the hand control is connected properly via the plug-type connection on the bathing. The red ding at the jack is now unseen. Press the ON button (green) on the hand control. The green control lamp is fulminated. . Now press the UP bitten (yellow). The backrest moves o an upright position first; then the [ift rises o His end position and switches off automatically.
Installation and use §. After bathing, press the UP button {yellow} on the hand control to move the sift to a convenient height {max. upper stop position}. Make sure that the side fiats do not get caught on bath fittings or hen dies. 7. Now the person bathing can leave the bath by sliding sideways from the seat surface. The Bellatrix switches off automatically after approx. 30 minutes. 1f you wish to switch off the bath lift manually, press red bunion on the hand control {the control lamp will go out}.
Installation and use 3. Hake resolutely sure that the sifting red Is always retracted completely. correct Incorrect 4. Now the drive unit can be removed from the seat unit in the direction of the arrow (see illustration). Note: The drive unit can only be removed at a specific angle. When R is completely folded down and locked, it can not be removed from the seal unit. Bring the backrest into the position shown in our Illustration; then remove the drive unit in the direction of the arrow. 5.
Maintenance and care Maintenance of the bathing The Bella vita is equipped with maintenance-free bearings and does not need any lubrication. A periodic maintenance check of the bailiff has to be conducted at least every 12 months. This check includes a visual inspection of all parts in particular clad-bearing parts. 1t also includes all the necessary function tests.
Maintenance and Care Maintenance of the battery charger The charging unit does not require any maintenance. The housing must only be cleaned with mild detergents that ave free from solvents, or by means of a damp cloth. Make sure that no liquid enters info the charging unit. Before using the charging unit again, always make sure that the unit is completely dry. If necessary, store the unit in a dry, ventilated place for several hours without connecting it to mains power.
Transport / mobile use Please observe the following instructions for mobile use: 1. Remove the hand control! from the bathing and transport separately. 2. Always protect the bathing against sliding or slipping during the transportation (e.g. in a car}. U Transport as two separate units The seat and drive units can be transported easy with two hand grips. 18 English 2. 1f the battery is subjected 1o low temperatures {e.g.
Appendix " Technical! Data Bella vita bathing Overall length (with backrest in & reclined position) Overall width (seat incl. side flaps) Width of seat Depth of seat Overall length of seat Sitting height min. Sitting height max. Height of spaciest Width of backrest Backrest adjustment Width of base plate Length of base plate Load capacity max. Total weight {ax. hand control} Total wait {incl. hand control} Weight of hand control! incl.
Appendix B Troubleshooting Error Possible cause H Remedy Lift does not move o Battery is flat — Charge battery * Contacts on hand control — Unplug hand control; wipe are contaminated contacts with a dry cloth and plug hand control in again * Hand control is not Check plug-lye connections connected properly Lift stops repeatedly =« Battery is flat — Charge battery « Excessive filing load — Traduces lifting load {(not max.
Appendix b warranty Q Our warranty for the Believable bathing will be in accordance with regal stipulations and/er regulations valid in the different countries. The warranty applies to Commercial and Domestic applications, subject to the conditions stated here. In the event of any part/product developing a manufacturing fault or design fault within the warranty period, replacement parks will be supplied free of charge. In all instances the warranty is provided to the first time purchaser or user only.
Appendix | Accessories and spare parks The st below shows the order numbers {part numbers} for original accessories and original spare pairs supplied by Drive Medical: Article Order Number * Seat and backrest covers Cover-Set Classic, white 460800252 Cover-Set Classic, blue 460800312 Cover-Set Classic, Grey 460800432 Cover-Set Comfort, white 450800252 Cover-Set Comfort, blue 450800312 Cover-Set Comfort, Grey 450800432 * Spare parts Power supply EU, Bella vita 450800401 Power supply UK, Bella vita 450800402
