User Manual
Table Of Contents
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. GETTING TO KNOW YOUR ARMOR X7
- Processor and Operating System
- Data Storage
- Dual Screen Display
- Video Graphics
- Wireless
- Optional GPS Capability
- Audio
- Batteries
- ARMOR Flexspace™
- ARMOR X7 Specifications
- Front Panel Features
- Rear Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Accessories for Your X7
- 3. GETTING STARTED
- Installing and Charging the Batteries
- Turning On Your X7 for the First Time
- Turning the Computer On Normally
- Putting the Computer in Sleep Mode
- Turning the Computer Off Normally
- Emergency Shutdown
- Indicator State Summary
- Activating your Wireless Radios
- Installing a Micro SD or SDHC Card
- Accessing and Using the GPS Receiver
- Operating the X7 Display
- Working with the Pen Screen
- Working with the Touch Screen
- Entering Data Using the Input Panel
- Using the FPS as a Simple Mouse Device
- Configuring Your Speakers
- Operating with the ARMOR X7 Vehicle Dock
- Using the Webcam
- Using the Screen Magnifier
- Tips for Proper Use and Care Of Your X7
- 4. NETWORKING
- 5. YOUR ARMOR X7 SOFTWARE
- Getting Started with Windows 7
- ARMORutils Program
- ARMORutils Main Dialog Window
- Backlight Setup Dialog Window
- Wireless Devices Dialog Window
- Programmable Button Settings Dialog
- Configuration Dialog Window
- Battery Monitor Dialog Window
- Screen Mode Setup Dialog Window
- Diagnostics Dialog Window
- ARMORutils About Window
- Pen and Touch Utility
- Tablet PC Settings Utility
- Pen Tablet Properties Utility
- Picasa 3®
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. BACKUP AND RESTORE PROCEDURES
- 8. MAINTAINING YOUR ARMOR X7
- 9. DISPLAY MANAGEMENT
- 10. BATTERY MANAGEMENT
- Safety and Handling Considerations for Your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating under Low Battery Conditions
- Battery Capacity
- Discharge/Recharge Cycles
- Battery Conditioning
- How to Optimize Battery Operating Time
- How to Monitor Battery Usage
- When to Replace a Battery
- Battery Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Batteries
- 11. DRS TECHNICAL SUPPORT
SECTION 3 GETTING STARTED PAGE 72
9711-26400-0001
EXPORT CONTROLLED – SEE PAGE 3
Rev -
Using the Webcam
Capturing Images and Video
Image and video capture is performed using the built-in webcam and image capture software.
Your X7 is provided with a version of Picasa 3™ image editor to demonstrate the image capture
process.
Follow the procedure in Table 12 to capture and save a still image or movie using this software.
NOTE
Remove the
blue protective film from the webcam lens before
using the camera.
Table 12. Capturing a Still Image or Video
STEP ACTION
1.
Double-click on the Picasa 3 icon on the desktop to open the Picasa application
window, as shown in Error! Reference source not found..
2.
Click on the “Capture photos or video…” button in the options bar. A Capture dialog
window will open displaying the current webcam image.
3.
To capture the image as a still image, click on the camera button below the image.
Each capture will appear as a thumbnail at the bottom of the window.
4.
When finished, click on the Done button to access editing and correction options or to
save or upload your images.
5.
To capture moving video, click on the Record button below the image. The capture
window will change to a viewer with options to view, save and upload your captured
video.
6.
To return to the main window, click on the Back to Library button.
7.
Refer to the Picasa Help resources for detailed instructions.