User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 4
NETWORKING
Page 104 of 234
ARMOR X10gx Tablet Computer
The u-center GPS Application Window
The diagram in the center shows the approximate positions of satellites relative to your location
that are within range of the receiver. The graph at the bottom of the page shows the signal
strength of each satellite. A green bar indicates acceptable signal strength; a blue bar indicates
marginal reception. You must have at least four satellites with acceptable signal strength to
generate reliable position data.
u-center User’s Guide
A complete description of the u-center software is beyond the scope of this manual. However,
an online User’s Guide is provided with your u-blox installation. To access the user’s guide,
select Start
à Computer à Local Disk (C:) à Program Files (x86) à u-blox à u-center à
Documentation
à User’s Guides and double-click on the u-Center_User_Guide pdf file.
NOTE: We recommend you create a shortcut to this file on the desktop.
Figure 58. U-Center GPS Application Window
Assisted GPS
Assisted GPS (AGPS) is an option that uses your wireless network connection to quickly
download the GPS almanac and ephemeris information your system needs to compute a first fix
on your location. This greatly reduces the time to first fix (TTFF).
With AGPS, your system can acquire an accurate fix in less than 30 seconds. Without AGPS,
the TTFF can take as long as 15 minutes depending on surrounding structures and the strength
of the satellite signals.