User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
![](/manual/drs-tactical-systems/633anh/user-manual-english/images/img-118.png)
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 5
YOUR ARMOR X10GX SOFTWARE
Page 117 of 234
ARMOR X10gx Tablet Computer
Radio ON/OFF Buttons
There is an ON and Off button for each radio that is installed or supported. When you first start
your ARMOR X10gx, all installed radios are ON or enabled (default condition). Each radio can
then be disabled by pressing its OFF button and re-enabled by pressing its ON button.
NOTE: Radios that are available but not installed appear here also and will not be grayed out.
Dock RF Switch
The Dock RF Sw button enables or disables the antenna configuration that is selected by the
Dock RF Mux switch. The initial setting for the Dock RF Sw is “Enable”. If the button is set to
“Disable”, the tablet will use its internal antennas.
Dock Power Switch
In earlier X10 series tablets, the 5 VDC power pins in the docking connector were always active
to ensure power to the docking stations. This is not necessary with the new X10gx docking
stations due to an automatic sensing circuit that turns off power to the docking connector
whenever the X10gx is undocked.
The initial setting for the Dock Power Sw is “Auto” to enable dock sensing. However, to use the
X10gx with some ARMOR legacy docks, the Dock Power Sw must be set to “Always On” (refer
to
Setting the X10gx for Power Operation with Legacy Docks).
Dock RF MUX Switch
Your X10gx contains an RF multiplexer circuit that is configured by the Dock RF Mux switch.
There are two RF coaxial docking connectors on the X10gx dock: one for an external WWAN
antenna and one for an external GPS antenna (see ARMOR X10gx Vehicle Docks
). Depending
on how it is configured, the RF multiplexer will automatically switch your GPS and/or WWAN
antennas to external antennas mounted on the vehicle whenever you dock the tablet.
You can select GPS only, WWAN only, or Both antennas. If only one external antenna is
selected, the other radio will operate on its internal antenna. The initial default setting for the
Dock RF MUX is “Both”.
Save Settings Button
Regardless of how you configure your radios and the Dock RF Switch during your session, they
will return to their default settings the next time you restart the computer unless you save your
settings using the Save Settings button.
Once you configure each radio and the RF switch to suit the way you normally use them (ON or
OFF), you can press the Save Settings button to save the current configuration as your new
default settings.
NOTE
If you exit ARMORutils completely or shut down your system with the
Radios ON/OFF Toggle set to OFF, this will be saved as the default setting
and the radios will all be off
the next time you start your computer.