User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 5
YOUR ARMOR X10GX SOFTWARE
Page 124 of 234
ARMOR X10gx Tablet Computer
Battery Monitor Dialog
The Battery Monitor dialog window is shown in Figure 70. This window provides the following
information about each battery:
• Current charge level (% of the maximum energy capacity)
• Current status – whether the battery is CHARGING, DISCHARGING, FULLY
CHARGED, FULLY DISCHARGED, READY or NOT READY. A READY status indicates
a waiting state, such as the batteries are fully charged and waiting to discharge or a
second battery is waiting for the first battery to reach a particular charge level.
NOTE: If the status is NOT READY, the system cannot read the battery status and a
fault condition exists.
• Estimated time to 90% of full charge
• Estimated time to full charge (if external power is connected) or the estimated remaining
operating time (if on batteries only)
There are also four buttons on this window that open additional dialogs or information windows:
Battery 1 Details, Battery 2 Details, Charger Settings and Conditioning Menu. The
functions of these buttons are described in the following paragraphs.
Figure 70. ARMORutils Battery Monitor Dialog Window