User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 5
YOUR ARMOR X10GX SOFTWARE
Page 127 of 234
ARMOR X10gx Tablet Computer
Charge Lowest First
If you choose Charge Lowest First, the battery with the lowest charge will be charged to
80%, followed by the next lowest battery. Once both are at 80%, the first charged battery will
be charged to 100%, followed by the second charged battery.
Click on OK to save the new default setting. Select CANCEL to exit without changing the
policy.
Conditioning Menu Button
Click on the Conditioning Menu button to open the Battery Conditioning window shown in
Figure 73. This window will display the conditioning cycle information for each battery. It also
allows you to select a single battery to condition, or to select both batteries.
Your X10gx batteries are self conditioning/calibrating and do not normally require conditioning.
NOTE
Conditioning, or calibration, should only be performed if you notice
that the levels reported by Windows or ARMORutils are
consistently different from actual battery performance, as this adds
to the total cycle count of the battery.
The conditioning process consists of first charging the battery to a full charge, then drawing the
charge down to its minimum, followed by charging the battery back to a full charge. The entire
conditioning process takes about 8 hours for two batteries.