User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
![](/manual/drs-tactical-systems/633anh/user-manual-english/images/img-134.png)
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 5
YOUR ARMOR X10GX SOFTWARE
Page 133 of 234
ARMOR X10gx Tablet Computer
considerably by checking the Record only when data changes option. With this option
selected, the recorder will only enter a line of data when any data point changes.
Your Event Recorder is pre-configured from the factory with this option checked. Uncheck it
if you want to record data continuously.
Status
The Status panel displays the time the logging was started, the time remaining (if Auto
Logging is used) and the time logging was stopped (either at the end of an auto-timed
period or when the STOP LOGGING button was selected).
Timer
Here you can set the duration of your logging session by typing in the number of hours
directly or by using the up/down arrows. The current maximum auto-timed logging duration
is 168 hours (1 week).
Start Timed Button
Click on this button to start the timed logging period.
Start Manual Button
Click on this button to manually start the logging process. The logging process will continue
until you select the STOP LOGGING button or the computer is turned off.
Stop Logging Button
Click on this button to stop logging either in auto-timed or manual mode. NOTE: In manual
mode, the logging will continue until you stop it or turn power off to the computer.
Close Button
Click on this button to close the Event Recorder window. Your logging session will continue
in the background.
Using the Event Log File
In addition to temperature change, the event log also records other key information about
the batteries, such as their manufacturer, model number, serial numbers and a history of
their charging and discharging during the logging period. A sample event log printout is
shown in Figure 78. The battery status codes and column headings are defined in the
header.
You can open and view the log file in any text application. The file can be printed out or
exported to a database program like Microsoft Excel or Access and converted to a graph or
chart.