User Manual
Table Of Contents
- Manufacturer: DRS Tactical Systems
- 9711-26020-0001D_ARMOR X10gx User's Guide-r.pdf
- WARNING SUMMARY
- 1. WELCOME AND INTRODUCTION
- 2. LEARNING ABOUT YOUR ARMOR X10GX
- Front and Top Panel Features
- Rear Panel Features
- Left Side Panel Features
- Right Side Panel Features
- Bottom Panel Features
- Included Components, Accessories and Support
- Optional Add-ons and Accessories for Your X10gx
- X10gx Specifications
- 3. GETTING STARTED
- Installing the Batteries
- Turning on your X10gx for the First Time
- Turning the X10gx On Normally
- Turning the Computer Off Normally
- Emergency Shutdown
- Putting the Computer into Sleep Mode
- Putting the Computer into Hibernate Mode
- Indicator State Summary
- Configuring and Controlling your Wireless Radios
- Configuring your Audio System
- Operating the X10gx Display
- Entering Data Using the Input Panel
- Using the Fingerprint Sensor (FPS)
- Using the Webcam
- Screen Magnifier
- Tips for Proper Use and Care Of Your X10gx
- 4. NETWORKING
- 5. YOUR ARMOR X10GX SOFTWARE
- ARMORutils™ Application
- Backlight Setup Dialog
- Getting Started with Windows 7
- Windows Display Utilities
- TrueSuite™ Fingerprint Recognition Software
- Realtek® HD Audio Manager Application
- Picasa 3® Image Capture
- Virtual Magnifying Glass™
- 6. TROUBLESHOOTING
- 7. MAINTAINING YOUR ARMOR X10GX
- Replacing the Solid-State Drive (SSD)
- Removing and Replacing the Batteries
- Installing a SIM Card
- Removing and Replacing a Memory Module
- Changing the BIOS Settings
- Setting the X10gx for Power Operation with Legacy Docks
- Changing the Power Button Default Action
- Creating an Event Log
- Caring For the Display Screen
- Cleaning the Tablet Case
- 8. DISPLAY MANAGEMENT
- 9. BATTERY MANAGEMENT
- Safety and Handling Considerations for your Batteries
- When to Charge a Battery
- How to Charge Your Batteries
- How to Tell When Batteries Have Finished Charging
- Battery Operating Time
- Operating Under Low Battery Conditions
- Battery Capacity and Charge
- Discharge/Recharge Cycles
- How to Optimize Energy Use
- Monitoring Battery Status
- Battery Conditioning/Calibration
- When to Replace a Battery
- Your Battery’s Warranty
- Where to Purchase Replacement Batteries
- How to Store Batteries When Not in Use
- Battery Tips for Best Performance
- Disposing Of Your Used Batteries
- 10. DRS TECHNICAL SUPPORT
- ACRONYMS
- GLOSSARY
- APPENDIX A
9711-26020-0001
Export Controlled – See Page 3
Rev D
SECTION 3
GETTING STARTED
Page 83 of 234
ARMOR X10gx Tablet Computer
Using the Fingerprint Sensor (FPS)
To initially set up your FPS software, double-click on the TrueSuite icon on the desktop and
click on Get Started to begin. This will take you through the steps to enroll, or register, your
fingerprint(s). The fingerprint sensor is located on the right side of the tablet in the middle of the
row of buttons.
Installing the FPS Software
Once you have enrolled your fingerprints, you will need to swipe in each time you restart the
computer.
To use the fingerprint sensor, swipe your finger or thumb from side to side at medium speed
across the sensor.
Using the Fingerprint Sensor
Open the TrueSuite application by double-clicking on the TrueSuite icon on the desktop or by
selecting Start
à All Programs and clicking on the TrueSuite folder in the programs list (you
may have to scroll down to see it). Click on the TrueSuite option to open the application, as
shown in
Using the TrueSuite Application
Figure 44. There are five user panels available. Click on the navigation icon in the
upper right corner to open a panel.
Figure 44. TrueSuite Application Window