Use Instructions

The DryBuddyFLEX 3 is designed in USA. Assembled in China.
©2020 by Enuresis Solutions, LLC
Enuresis Solutions, LLC
51 W. Fairmont Avenue, Suite 2
Savannah, GA 31406 USA
1-912-352-8854
[e-mail]
• The DryBuddy alarm is intended for use as a bed-wetting
and enuresis alarm by children of age ve and older, or as
recommended by a medical authority. It can be used by older
patients as a urine sensor and wetness alarm and as an
incontinence alarm.
• The DryBuddy system is a medical device and should be
treated as such. Do not use roughly or damage.
• Do not use as a potty training aid for babies, toddlers and
young children.
• Make certain that no parts of the DryBuddy or sensor are put
in the mouth for any reason as this could cause choking or
other harm.
• Observe all sanitary precautions to keep the sensor clean and
the alarm parts clean and dry.
• Do not use the sensor for more than one user without
thorough cleaning.
• Do not strike the magnetic sensor or cap on hard surfaces or
make them hot as this can reduce magnetism.
• The DryBuddy system is designed to sense urine or salty
water. It is less eective in sensing plain water.
A7
Good Things Happen with DryBuddy
�
Raising the Standards for
Convenience, Performance and Value.
Caution when Using the DryBuddy System
Introduction & Quick-Use Instructions
FLEX 3
DryBuddyFLEX 3 Quick-Use
Instructions (Con’t)
DryBuddyFLEX 3 Quick-Use
Instructions (Con’t)
A4 A5
A6
Attaching the wireless Sensor to optional DryBuddy Wetness
Sensing briefs:
1. The patient (child) wears the briefs.
2. The Sensor’s male snaps are inserted into the female
snaps at the waist of the briefs and rmly attached.
3. The Velcro is rmly strapped around the Sensor to help keep it in
place.
Synchronizing allows the Sensor, Transceiver and optional Remote
to recognize each other and work together. A DryBuddyFLEX
3 system must be synchronized. A new system, consisting of a
further synchronizing. Synchronizing is required whenever
• A NEW Transceiver, Sensor or Remote is to be used, or
• Synchronization has been lost for any reason.
When detaching the sensor from the snaps on the briefs please hold
the briefs at one sensor location and gently detach the sensor with
the other hand. Do this for both snaps. Pulling the sensor o without
holding the snaps on the briefs can damage the snaps and briefs.
Note: A new DryBuddyFLEX 3 system, consisting of a boxed
Sensor, Transceiver and Remote, has been synchronized at the
factory and is ready to use.
To synchronize:
1. Attach the Transceiver to its power supply, and conrm that
the Transceiver is in its SLEEP state (Yellow light).
2. Press the Synch button on the side of the Transceiver. The
light under the Power button on the Transceiver will become
ashing BLUE. While the light is BLUE (15 seconds), the
Sensor and Remote (if used) must be synchronized.
3. First trigger the Sensor. This can be done by dipping both
sensor magnets in a cup of salt water, or by pressing a clean
and non-oily key or knife against both magnets. A beep will
be heard and the light continues ashing BLUE.
4. If a Remote is not being used, let the Blue light continue
ashing. It will stop ashing within 15 seconds and the
Transceiver light will turn GREEN.
5. If a Remote is being used, press the OFF button on the
Remote while the BLUE light is ashing. Two beeps will be
heard and the ashing BLUE light will turn GREEN.
Once the Transceiver light turns GREEN, the system is synchronized. If
the synchronizing is not completed in the 15 seconds while the BLUE
light is ashing, start the synchronizing process from the beginning.
While synchronizing or using the DryBuddyFLEX system, please
remember that triggering the Sensor makers it dormant for 2
minutes. So please wait abut 2.5 minutes before attempting to use
the Sensor again.
If the DryBuddyFLEX 3 is perceived to not work or has stopped working,
please synchronize it rst as it may have lost its synchronization. Without
synchronizing, the DryBuddyFLEX 3 system will not work.
The DryBuddyFLEX 3 has many useful features which can be
individually set and controlled by the user. Understanding the
features can help to use them successfully. Signicant relevant
information about the DryBuddyFLEX 3 and its use is provided
on www.DryBuddy.com under
Our Products → DryBuddyFLEX → DryBuddyFLEX 3
Instructions
Please refer to the DryBuddyFLEX FAQ section in www.DryBuddy.
com for additional information, advice and many answered questions:
www.DryBuddy.com → FAQ → DryBuddyFLEX
Note: The feature-rich DryBuddyFLEX 3 is the most sophisticated
bedwetting alarm available today. Please contact DryBuddy at
1-912-352-8854 or [e-mail] with any questions,
comments or issues.
Synchronizing the DryBuddyFLEX 3
System is necessary.
Other DryBuddyFLEX 3 Features, Controls and
Operations
Please read the DryBuddyFLEX 3 Supplemental
Instructions To Help in its Successful Use.
Attaching the wireless Magnetic Sensor to standard cotton briefs:
1. The Sensor is attached on the outside of the briefs at the point
of urination. Position the Sensor carefully on the briefs. The alarm
will only alert when the material of the briefs at the gap between
the two magnets is quickly wet.
2. The stainless steel magnets point towards the body.
3. The magnetic Cap is placed on the inside of the briefs and
directly opposite the magnets so that the briefs are clamped
between the Sensor and the Cap.
4. With male briefs having a pouch, the Sensor should be placed
inside the pouch with the magnets pointing towards the body.
or
Attaching the Wireless Magnetic Sensor
These provide additional insights and advice that can be very
helpful in using the DryBuddyFLEX 3 system.
the devices synchronized at the factory and can be used without
Sensor, Transceiver and Remote packed in a box, comes with