Use and Care Manual

DRYLOK® Extreme Masonry Waterproofer
Latex Base DRYLOK EXTREME Masonry
Waterproofer is the Next Generation in
waterproof coatings. Features Flexible
Encapsulated Polymers which squeeze into
the masonry for the ultimate in waterproof
protection.
Specially formulated to resist mildew growth
on the dry paint lm with the incorporation
of an environmentally friendly green
biocide. Fully transferable 15 year warranty.
Tested to ASTM D-7088 Resistance to
Hydrostatic Pressure at 15 psi and ASTM D-
6904 Resistance to Wind Driven Rain.
Reduces radon gas penetration.
Bright white, smooth finish
Resists mildew growth on the dry paint film
Resists 15 psi, equivalent to a wall of water
33 ft. high
Fully transferable 15 year warranty
Guaranteed to stop water, even under
pressure
Features flexible encapsulated polymers
Reduces radon gas penetration
White is tintable
Ideal for interior, exterior, above or below
grade masonry walls, basement walls,
retaining walls, foundations, landscape walls,
cinder blocks, concrete blocks, bare
concrete swimming pools, stucco and brick.
DRYLOK Extreme may be applied over
previous coatings in sound condition, but the
warranty is void. Not formulated for
horizontal surfaces subject to foot traffic.
COMPOSITION:
Latex base
SHEEN:
N/A
% WEIGHT SOLIDS:
64-66%
% VOLUME SOLIDS:
55-57%
DENSITY (LBS./US GAL.):
9.8-10.0
VISCOSITY:
110-120 Ku@77ºF
pH:
9.0-9.9
COLOR:
• White – ready mixed formula
DRY TIME:
• 2 hours
• To recoat: 3 hours
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
Note: When painting the inside of
concrete non-potable watertanks, allow
to dry at least 1 week before puing
into service.
CLEAN UP:
Warm soapy water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 75-100 sq. ./gallon
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
• 13-21 wet mils/coat
FLASH POINT:
N/A
SHELF LIFE:
5 Years
FREEZE/THAW:
ree cycles
CONTAINER SIZES:
One quart (US), One gallon (US), and
ve gallon (US) containers
Does not exceed 100 g/L
Use alkali-proof universal tinting colorants.
Use only 50% of color normally
recommended. Do not use more than 2 .
oz. of colorant per gallon.
Masonry surfaces must be clean and free from
dirt, dust, grease, oil, form release compound,
frost or paint. Patch all holes or cracks with
DRYLOK FAST PLUG®, a fast seing hydraulic
cement, and smooth the patch evenly with
the surface around it. Check the joint where
the oor and wall meet and ll any breaks
with DRYLOK FAST PLUG®.
EFFLORESCENCE, a white, powdery,
crystal-like deposit visible on the masonry
surface must be removed.
DRYLOK ETCH or muriatic acid, used
according to manufacturer’s directions, are
effective efflorescence removal agents. All
masonry surfaces are subject to occurrences
of efflorescence.
May be applied on slightly damp surfaces, but
best results are obtained when applied over
dry surfaces. For best waterproong results,
wait for a dry (rain-free) period.
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
S
o
a
p
DRY TIME:
2 Hours
Recoat 3 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Minimum
SPREAD RATE:
100 Sq. Ft./Gallon