Use and Care Manual

DRYLOK® FAST PLUG® Hydraulic Cement
DRYLOK Fast Plug is a quick seing hydraulic
cement. It sets in 3-5 minutes to stop active
leaks, even under pressure. Seals open joints,
very large cracks in masonry walls and oor
and wall joints.
Fast setting hydraulic cement
Sets in 3-5 minutes
Stops water, even under pressure
Patch mortar joints, cracks and holes in
masonry walls
No top-coat required
Anchors metal to concrete. Ideal for sealing
oor and wall joints and selement cracks in
masonry walls and swimming pools. is fast-
seing hydraulic cement patches holes even
where water is actively owing through
them.
Mix only enough for immediate use, because
DRYLOK Fast Plug sets in 3-5 minutes.
Cannot be reworked once it has set.
COMPOSITION:
Sand and cement
SHEEN:
N/A
% WEIGHT SOLIDS:
100%
% VOLUME SOLIDS:
100%
DENSITY (LBS./US GAL.):
24.0 ± 0.3%
VISCOSITY:
N/A
COLORS:
• Gray – ready mixed formula
SET TIME:
• 3-5 minutes
Note: Maximum cure and dry time will
be prolonged when slightly humid and
when damp, cool conditions prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 16 cu. in./lb.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
N/A
FLASH POINT:
N/A
SHELF LIFE:
Unlimited in tightly closed container
FREEZE/THAW:
N/A
CONTAINER SIZES:
One and a half pound (US), four pound
(US), ten pound (US) and y pound
(US) containers
N/A
N/A
Wear eye protection, rubber gloves and a
dust mask. e area to be patched should
be cleaned thoroughly by wire brushing,
scraping or any other effective process.
Back chisel out the area to be patched to the
shape of an inverted “V” (the point at the
surface). is allows the patch to expand and
lock into the surface. Wet down the area
prior to patching to help the DRYLOK Fast
Plug cure properly.
DRYLOK Fast Plug and clean mixing water
should be at room temperature prior to
mixing. Mix 3 parts Fast Plug and 1 part
water thoroughly to a puy or heavy
troweling consistency. is mixture will set in
3-5 minutes. e use of colder water will
retard the seing time. Mix only enough for
immediate use due to the quick seing time.
DRYLOK Fast Plug cannot be reworked once
it has set. In cold weather, use warm (90°F.)
water for mixing; also soak surface with warm
water before application.
Mix only enough for immediate use, because
DRYLOK Fast Plug sets in 3-5 minutes.
Cannot be reworked once it has set.
Mix in small batches only. Mix only enough
for use in 3 minutes. Discard all le over
mixed patching material prior to starting a
new batch. Le over patching material will
chemically react with new material in the
mixing receptacle.
If you scrape, sand, or remove old paint, you
may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE
SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
SET TIME:
3-5 Minutes
CLEAN-UP:
Soap and Water
COVERAGE:
1 Application
SPREAD RATE:
16 Cu. In./Pound
correct
incorrect