Use and Care Manual
LR413
Fast Plug® – Gray
1
1
⁄2 LB. 6/Case . . . . . . . . . . . . . . . .00919
4 LB. 4/Case . . . . . . . . . . . . . . .00917
10 LB. 2/Case . . . . . . . . . . . . . . .00924
50 Lb. 1/Case . . . . . . . . . . . . . . .00930
DISCLAIMER:This information is furnished without warranty,
representation, inducement or license of any kind, except that it
is accurate to the best of UGL’s knowledge, or obtained from
sources believed by UGL to be accurate, and UGL does not
assume any legal responsibility for use or reliance upon same.
Before using any product, read the label.
PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-
a
pproved respirator to control lead
exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start,
nd out how to protect yourself and your
f
amily by contacting the National Lead
Information Hotline at 1-800-424-LEAD or
l
og on to www.epa.gov/lead.
For Active Leaks (the presence of owing
water through a break in the surface): Mix
appropriate amount of Fast Plug. In
approximately 2
1
/2 - 3 minutes, the mixture
will become warm to the touch which
indicates it is commencing to set. At this time
force the Fast Plug into the opening with the
palm of the hand. Hold in place for 3-5
minutes, assuring a complete set and sufficient
bond to stop the ow of water. e patched
area may be smoothed and trimmed to the
surrounding area in approximately 5 minutes.
Fast Plug may be painted when set with
DRYLOK Masonry Waterproofer, Latex Base
DRYLOK Masonry Waterproofer, DRYLOK
Powdered Masonry Waterproofer or
DRYLOK Concrete Floor Paint.
For Inactive Leaks, Patching, Anchoring:
oroughly soak the area to be patched. is
will prevent the surface from sucking the
water out of the patching material. Apply with
knife or trowel. Use the surface to smooth the
patch evenly. When anchoring, chisel or drill
hole in the masonry surface slightly larger than
item to be anchored. Make certain mixed Fast
Plug is tamped rmly into hole and around
metal part.
Cancer hazard: Contains Crystalline Silica,
which can cause cancer. Risk of cancer
depends on duration and level of exposure
to dust generated from sanding surfaces or
grinding.
Use only with adequate ventilation. Do
not breathe dust. Avoid eye contact or
prolonged contact with skin. Avoid exposure
to dust by wearing an appropriate (NIOSH
approved) particulate respirator during
mixing, application and clean up. Follow
r
espirator manufacturer's directions for
respirator use. Close container aer each
use. Avoid contact with eyes, skin and
clothing. Wash thoroughly aer handling.
First Aid: If you experience difficulty in
b
reathing, leave the area to obtain fresh air.
If continued difficulty is experienced, get
m
edical aention immediately. In case of eye
contact, ush with plenty of water for at least
15 minutes. Consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN
is product contains a chemical known to
the State of California to cause cancer.
EYES: Immediately ush eye throughly with
water, continue ushing eye for at least 15
minutes, including under lids, to remove all
particles. Call a physician.
SKIN: Wash skin with cool water and pH –
neutral soap or mild detergent. See a
physician if irritation is present.
INGESTION: Do not induce vomiting. If
conscious, drink plenty of water. Call a
physician.
INHALATION: Remove to fresh air, restore
breathing. If breathing is difficult, administer
oxygen. If not breathing, give articial
respiration.
For additional health and safety information
please refer to the “Safety Data Sheet”.
N/A.
Compressive strength of cured material at:
1 Hour 311 PSI
3 Hours 365 PSI
8 Hours 396 PSI
24 Hours 2650 PSI
7 Days 3050 PSI
28 Days 11975 PSI