TDS

DRYLOK® Original Basement & Masonry Waterproofer
DRYLOK® Original Basement & Masonry
Waterproofer is the manageable way to
solve water seepage problems. Reduces
radon gas penetration by reducing vapor
transfer.
Guaranteed to stop water
No pre-mixing or pre-wetting
Resists 10 PSI, equivalent to a wall of water
22 ft. high
Fully transferable 10 year warranty
Resists 98 MPH wind-driven rain
Tintable
Formulated for waterproong all interior,
exterior, above or below grade masonry
walls, cinder and concrete blocks, stucco
and brick, retaining walls, sh ponds,
birdbaths, planters, water features,
basement walls, and foundations.
DRYLOK® Original Basement & Masonry
Waterproofer® may be applied over
previous coatings in sound condition, but
the warranty is void. Not formulated for
horizontal surfaces subject to foot traffic.
COMPOSITION:
Latex base
SHEEN:
Flat
% WEIGHT SOLIDS:
65-67%
DENSITY (LBS./US GAL.):
12.7-12.8 (1.52 g/L)
VISCOSITY:
120-130 Ku @ 77ºF (25ºC)
pH:
9.5-9.9
COLORS:
• White – ready mixed formula
• 3 ready mixed colors
DRY TIME:
• 2-3 hours
• To recoat: 2-3 hours
• Top coat with latex paint: 24 hours
Note: Maximum cure and dry time
will be prolonged when slightly
humid and damp, cool conditions
prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container, and unused contents in
accordance with local, state, and
federal regulations.
COVERAGE (SQ. FT./GAL.):
First coat: Wet: 21 Dry: 10 mils @ 76
sq. ./gal.
Second coat: Wet: 13 Dry: 7 mils @
125 sq. ./gal.
Note: Actual coverage will vary
depending upon application
method, surface texture, and
porosity.
RECOMMENDED FILM THICKNESS/COAT:
21-13 wet mils/2 coats
(533-330 microns)
SHELF LIFE:
5 Years unopened container
FREEZE/THAW:
ree cycles
CONTAINER SIZES:
One quart (946 mL), one gallon
(3.785 L), two gallon (7.5 L) and ve
gallon (18.9 L) containers
Does not exceed 100 g/L
Tint to light shades with alkali-proof
universal tinting colors. Use only 25% of
color normally recommended. Do not use
more than 2 . oz. (15 g/L) of colorant per
gallon.
Surface must be clean and free from dirt,
dust, grease, oil, form release compound, or
paint. Patch all holes, or cracks, and the
oor/wall joint with DRYLOK® Fast Plug®, or
a fast seing hydraulic cement, and smooth
the patch evenly with the surface around it.
Check the joint where the oor and wall
meet and ll any breaks with DRYLOK® Fast
Plug®.
EFFLORESCENCE, a white, powdery,
crystal-like deposit visible on the masonry
surface must be removed.
DRYLOK® Etch (liquid or powder) or
muriatic acid, used according to
manufacturer’s directions, are effective
efflorescence removal agents. All masonry
surfaces are subject to occurrences of
efflorescence.
Old paint in poor condition must be
removed by wire-brushing, sand blasting,
or by using other suitable means.
May be applied on slightly damp surfaces,
but best results are obtained when applied
over dry surfaces. For best waterproong
results, wait for a dry (rain-free) period.
If you scrape, sand, or remove old paint,
you may release lead dust. LEAD IS
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.UGL.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
S
o
a
p
DRY TIME:
2-3 Hours
Recoat 2-3 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Minimum
SPREAD RATE:
100 Sq. Ft./Gallon
07 14 16 COLD FLUID-APPLIED WATERPROOFING
09 91 13 EXTERIOR PAINTING | 09 91 23 INTERIOR PAINTING
DIV. 07 & 09