Specifications

ManualsBrandsDSC ManualsHome building and DecorPC 5010

System Introduction

S E C T I O N 1

1.1 Specifications

Control Panel Specifications

Flexible Zone Configuration:

• 8 Fully Programmable Zones

• 38 Access Codes: 32 User, 1 System Master, 2 Partition Master, 2 Duress and 1 maintenance

• Expandable to 32 Zones

• Keypads with zone inputs available (PC/KP5508Z, PC/KP5516Z, PC/KP5532Z, LCD/KPL5500Z)

• Hardwired expansion available using the PC5108 Eight Zone Expansion Module

• Wireless expansion available using the PC5132 Wireless Zone Expansion Module (up to 32 wireless

zones, 900MHz, True Spread Spectrum Technology, Fully Supervised)

• Normally Closed, Single EOL, or Double EOL zone supervision

• 2-Wire Smoke Input (via PGM2 input)

• 27 Zone Types, 8 Programmable Zone Options

• 2 Partitions

Audible Alarm Output:

• Supervised Bell Output (current limited at 3 amps), 12 V

• Steady or Pulsed Output

EEPROM Memory:

• Will not lose programming or system status on complete AC and Battery failure

Programmable Outputs:

• Up to 14 Programmable Voltage Outputs, 23 programmable options

• One High Current (300 mA) PGM output with 2 wire smoke detector capability on main panel

• Maximum Loop Current is 1.5 mA when the 2-wire smoke detector configuration is used

• One Low Current (50 mA) PGM output on main panel

• Eight Additional Low Current (50 mA) PGM outputs available using the PC5208 module

• Four High Current (1 Amp) PGM outputs Available Using the PC5204 module

• 1 PC5204 Output Fully Supervised for Siren Output

Powerful 1.5 Amp Regulated Power Supply:

• 500 mA Auxiliary Supply, 12 V

• Positive Temperature Coefficient (PTC) components replace fuses

• Supervision for loss of AC Power, Low Battery

• Internal Clock Locked to AC Power Frequency

Power Requirements:

• Transformer = 16.5 VAC, 40VA

• Battery = 12 volt 4 Ah minimum rechargeable sealed lead acid

Remote Keypad Specifications:

• 8 Different Keypads Available:

- PC5508(Z)/KP5508(Z) 8 Zone LED Keypad - PC5532(Z)/KP5532(Z) 32 Zone LED Keypad

- PC5516(Z)/KP5516(Z) 16 Zone LED Keypad - LCD5500(Z)/KPL5500(Z) Alphanumeric Keypad

• Each Keypad has 5 Fully Programmable Function Keys • Connect up to 8 Keypads

• Four Wire (Quad) Connection to Keybus • Built in Piezoelectric Buzzer

Digital Communicator Specifications:

• Supports all Major Formats including SIA and Contact ID • Event Initiated Personal Paging

• 3 Programmable Phone Numbers • 2 Account numbers

• Supports LINKS1000 Cellular Communication • DTMF and Pulse Dialing

• DPDT Line Seizure • Anti-jam Feature

• Split Reporting of Selected Transmissions to Each Telephone Number

System Supervision Features

The PC5010 continuously monitors a number of possible trouble conditions including:

• AC Power Failure • Trouble by Zone • Fire Trouble

• Telephone Line Trouble • Low Battery Condition • Bell Output Trouble

• Loss of Internal Clock • AUX Power Supply Fault • Tamper by Zone

• Failure to Communicate • Module Fault (Supervisory or Tamper)

Summary of content (48 pages)

PAGE 1
System Introduction S 1.
PAGE 2
S Y S T E M I N T R False Alarm Prevention Features • Audible Exit Delay • Audible Exit Fault • Quick Exit • Swinger Shutdown • Communication Delay • Rotating Keypress Buffer O D U C T I O N • Urgency on Entry Delay • Recent Closing Transmission • Cross Zone Police Code Alarm Additional Features • Auto Arm by Partition at Specified Time • Keypad Activated Alarm Output and Communicator Test • Keypad Lockout • Audio Capability using the PC5928 Audio Interface Module which allows local inte
PAGE 3
S Y S T E M I N T R O D U C T I O N WLS907 Wireless Slimline Universal Transmitter The wireless Slimline Universal Transmitter can be used with the PC5132 Wireless Receiver to add wireless door or window contacts in a smaller package. The unit comes with three ‘AAA’ batteries and has built-in contacts. WLS908 Wireless Panic Pendant The wireless Panic Pendant can be used in conjunction with the PC5132 Wireless Receiver to include personal wireless protection.
PAGE 4
S Y S T E M I N T R O D U C T I O N Three additional devices are available (These devices are not UL Listed): PC5921 Intercom Audio Station (This device is not UL Listed) can be used in conjunction with the PC5928 Audio Interface Module. PC5921 EXT Door Box Audio Station (This device is not UL Listed) can be used in conjunction with the PC5928 Audio Interface Module.
PAGE 5
Getting Started S E C T I O N 2 The following sections provide a complete description of how to wire and configure devices and zones. 2.1 Installation Steps The following steps are provided to assist with the installation of the panel. It is suggested that you read over this section briefly to get an overall understanding of the order of installation. Once this is done carefully work through each step.
PAGE 6
G 2.2 E T T I N G S T A R T E D Terminal Descriptions AC Terminals - AC The panel requires a 16.5 volt, 40 VA transformer. Connect the transformer to an unswitched AC source and connect the transformer to these terminals. Do not connect the transformer until all other wiring is complete .
PAGE 7
G E T T I N G S T A R T E D Ensure the plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C.F.R. Part 68, SubPart F. For proper operation there must be no other telephone equipment connected between the control panel and the telephone company facilities. Do not connect the alarm panel communicator to telephone lines intended for use with a FAX machine.
PAGE 8
G E T T I N G S T A R T E D Other Devices Read the manufacturer’s literature carefully to determine the maximum current requirement (during activation or alarm) and use this value for loading calculations. Do not allow connected devices to exceed the system capabilities during any possible operational mode. 2.5 Assigning Zones to Zone Expanders The main panel contains zones 1 to 8. Additional zone expanders may be added to increase the number of zones on the system.
PAGE 9
G 2.6 E T T I N G S T A R T E D Keypad Assignment There are 8 available slots for keypads. LED keypads by default are always assigned to slot 1 while the LCD5500Z is always assigned to slot 8. Keypads can each be assigned to a different slot (1 to 8) which offers two advantages. The panel can supervise the keypad connection to indicate a trouble condition if it is removed. Also keypads can be assigned to operate a specific partition or operate as a global keypad. 2.6.
PAGE 10
G 2.8 E T T I N G S T A R T E D Removing Modules If a module is no longer required on the system the panel must be told to no longer supervise the module. To do this remove the module from the Keybus and perform the Enable supervision function again (See Section 2.7 “Enable Supervision”). The panel will see the module has been removed and will no longer supervise it. 2.9 Zone Wiring For a complete description of the operation of all zone types, please refer to Section 5.
PAGE 11
G 2.9.4 E T T I N G S T A R T E D Fire Zone Wiring - 4 wire Smoke Detectors All zones defined as Fire (See Section 5.1 “Zone Definitions”) must be wired according to the following diagram: For a complete description of how fire zones operate, see Section 5.1 “Zone Definitions”. 2.9.5 Fire Zone Wiring - 2 wire Smoke Detectors If PGM2 has been programmed for 2 Wire Smoke Detector connection (See Section 5.
PAGE 12
G 2.10 E T T I N G S T A R T E D Keypad Zones Keypads with zone inputs can be connected to devices such as door contacts. This saves you from running wires back to the control panel for every device. To install the keypad, open the keypad plastic by removing the screw at the bottom of the unit. Locate the five terminals on the keypad circuit board. Connect the four Keybus wires from the control panel: the red wire to R, the black to B, the yellow to Y and the green to G.
PAGE 13
Keypad Commands S E C T I O N 3 All keypads provide complete information and control of the alarm panel. The panel can be completely programmed via any keypad on the system. LED keypads provide function indicator lights and individual zone indicator lights for the alarm circuits. The LCD keypad provides function indicator lights and word descriptions for zone status. The following sections describe how to arm, disarm and perform other keypad functions. 3.
PAGE 14
K 3.3 E Y P A D C O M M A N D S Auto Bypass When the system is armed and any zone or zone(s) on the system have been programmed as Stay/Away the panel will immediately turn on the ‘Bypass’ light. It will then monitor all zones programmed as Delay 1 and Delay 2. If no delay type zone is violated by the end of the exit delay the panel will bypass all Stay/ Away type zones.
PAGE 15
K E Y P A D C O M M A N D S A description of the various troubles are as follows: Trouble [1] - Service Required This light will be on if any of the following trouble conditions are detected by the control panel; Low Battery, Bell Circuit Trouble, General System Trouble, General System Tamper, General System Supervisory, PC5204 Low Battery and PC5204 AC Failure. If a ‘Service Required’ trouble is present press [1] to determine the specific trouble present.
PAGE 16
K [✱]+[4] [✱]+[5] E Y P A D C O M M A N D S Door Chime On/Off If enabled the keypad will beep 5 times rapidly when a zone is tripped and restored. The panel will only do this for zones with the Door Chime attribute enabled and if the door chime feature is enabled (See Section 5.2 “Zone Attributes”). To turn Door Chime on/off: 1. Press [✱] [4]. 2. The keypad will beep 3 times rapidly when the Door Chime feature is enabled and one long beep when the feature is disabled.
PAGE 17
K E Y P A D C O M M A N D S How to erase Access Code: Select the code to be erased and press [✱]. [✱]+[6] User Functions This keypad command can be used to program several different functions. The following are the items programmable: [1] - Time and Date [4] - System Test [6] - User Initiated Call-Up [2] - Auto-Arm Enable * [5] - Enable DLS (Downloading) [7] - For future use [3] - Auto-Arm Time * Auto-Arm items (noted with the “ * ” symbol) are programmable by Partition.
PAGE 18
K E Y P A D C O M M A N D S [✱ ✱ ] [7] Command Output Functions There are four output functions available to the user. Each function can be performed when the system is either armed or disarmed. [✱] [7] [1-4] – Command Output Option #1-4: Press [✱] [7] [1-4] [Access Code, if required] to activate outputs programmed as PGM output option [19][22]. These outputs can be used for operating devices such a garage door opener, lighting or door strikes.
PAGE 19
K E Y P A D C O M M A N D S “Chime” - Door Chime On/Off Pressing the key will toggle the Door Chime feature ON or OFF. One solid beep means the feature has been disabled, three short beeps means it has been enabled. “Reset” - Reset Smoke Detectors Pressing this key will cause the panel to activate for 5 seconds any output programmed as Sensor Reset. In addition two wire smoke detectors connected to PGM2 will also be reset (See Section 3.4 “[✱] Commands, [✱][7][2]”).
PAGE 20
K E Y P A D C O M M A N D S [14] - [✱]+[7]+[2] Smoke Detector Reset This function key provides the user with a simple method for activating a PGM output programmed as either option [03] Sensor Reset or [20] Command Output option 2. [15] - General Voice Prompt Help This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are being used. When the function key is pressed, the intercoms will perform a Help page.
PAGE 21
How to Program S E C T I O N 4 The following section of the manual describes how to enter Installer Programming and how to program the various sections. It is extremely important that you read the following section of the manual to completely understand how to program the panel. 4.1 How to Enter Installer Programming Installer Programming is used to program all communicator and panel options. The Installer Code is [5010] at default but may be changed to prevent unauthorized access to programming.
PAGE 22
H O W T O P R O G R A M If you are using a pulse format, a decimal zero [0] does not transmit. Programming a zero [0] tells the panel not to send any pulses for that digit. Decimal zero [0] is a filler digit. To make a zero [0] transmit, it must be programmed as a Hexadecimal ‘A’. Example: for the three digit account number ‘403’, you would enter [4], [✱] [1] [✱] [3], [0].
PAGE 23
Program Descriptions S E C T I O N 5 The following section explains all the programmable features including how the feature operates, options that pertain to the feature and a summary of program locations that require programming. 5.1 Zone Definitions These sections will allow you to select how each of the 32 zones will operate. Each zone requires a 2 digit entry. In addition to selecting how each zone will operate, attributes may be programmed by zone (See Section 5.2 “Zone Attributes”).
PAGE 24
P [09] R O G R A M D E S C R I P T I O N S 24 Hour Supervisory Zone If this zone is violated, whether armed or disarmed, the panel will report to the central station, and log the zone fault. Do not wire 24-Hour Supervisory zones on keypad zone terminals. 24 Hour Supervisory Buzzer Zone Whether armed or disarmed, when this zone type is violated the panel will immediately latch the keypad buzzer until a valid user code is entered and will communicate immediately to the central station.
PAGE 25
P R O G R A M D E S C R I P T I O N S Swinger Shutdown Enable (Shall not be enabled on UL Listed systems) Determines if the panel will shut down the communicator for the zone after the swinger limit is reached (See Section 5.17 “Swinger Shutdown”). Transmission (TX) Delay Enable Determines if the panel will delay communicating the alarm reporting code to the central station (See Section 5.18 “Transmission Delay”).
PAGE 26
P 5.5 R O G R A M D E S C R I P T I O N S Communicator - Account Numbers There are two Partition Identifier Codes (or Account Numbers) programmable, one for each Partition. The Account Number is used by central station to determine which panel is calling. If the panel is programmed as two Partitions both Account Numbers must be programmed. The panel will report to the central station by Partition.
PAGE 27
P R O G R A M D E S C R I P T I O N S If the SIA Sends Automatic Reporting Codes option is disabled the panel will operate as follows: 1. If the reporting code for an event is programmed as [00] or [FF] the panel will not attempt to call central station. 2.If the reporting code for an event is programmed as anything from [01] to [FE] the panel will send the programmed reporting code. 3.Bypassed zones will never be identified, regardless of reporting code for “partial closing”.
PAGE 28
P R O G R A M D E S C R I P T I O N S A Partial Closing Reporting Code will be transmitted if a Partition is armed with zones manually bypassed. The code will also be transmitted if a Partition Auto Arms with zone(s) in violation.
PAGE 29
P R O G R A M D E S C R I P T I O N S The Auxiliary Power Supply Trouble Alarm Reporting Code will be transmitted if the AUX output is shorted. The AUX output control incorporates a fuseless design. When excessive current is drawn the panel will automatically shut off the output. The panel will constantly check the AUX output and when the excessive current draw is removed the panel will reset the output and transmit an Auxiliary Power Supply Trouble Restoral Reporting Code.
PAGE 30
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Reporting Codes ......................................................................................... Sections [320] to [353] Delinquency Follows Zone Activity ............................................................ Section [380], Option [8] Delinquency Transmission Cycle ...............................................................
PAGE 31
P R O G R A M D E S C R I P T I O N S Keypads can be assigned to work on either partition or can be assigned for Global operation (See Section 2.6 “Keypad Assignment”). Each partition can be programmed to report using a different Account Number (See Section 5.5 “Communicator - Account Numbers”). Some of the Programmable Output options are also selectable by Partition (See Section 5.10 “PGM Outputs”). The Partition 2 Enable option must be programmed before Partition 2 will operate.
PAGE 32
P R O G R A M D E S C R I P T I O N S [10] Latched System Event (Strobe Output) The output will activate when any of the selected system events (alarms) occur on the system. In the armed state, the output will deactivate only once the system is disarmed. If an alarm activates this output in the disarmed state, the output will deactivate if a user enters a valid access code while the Bell Cut-off timer is counting down.
PAGE 33
P 5.10.2 R O G R A M D E S C R I P T I O N S PGM Output Attributes In addition to programming the output type, you must also program the PGM output attributes for each output. PGM output options [09] “System Trouble” and [10] “Latched System Event” have their own unique set of attributes listed below the description of each output type.
PAGE 34
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Bell Cut-off .............................................................. Bell Circuit Trouble Reporting Code ....................... Bell Circuit Trouble Restoral Reporting Code ........ Temporal Three Fire Signal Enable/Disable .......... Fire Bell Continuous ...............................................
PAGE 35
P R O G R A M D E S C R I P T I O N S For commercial applications Bell Squawk on Entry Delay may be enabled. The panel will squawk the alarm output once every second until the entry delay expires or the system is disarmed. This feature must not be used with 2 partitions. Since two Delay zones are programmable, and therefore two different Entry Delays, when the panel is armed it will use the Entry Delay for the first Delay zone violated.
PAGE 36
P 5.19 R O G R A M D E S C R I P T I O N S Keypad Backlighting The keys of all the keypads can be backlit to provide easy viewing in dim lighting conditions. If the Keypad Backlighting Option is enabled the keys will be illuminated. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Keypad Backlighting Option ................................... Section [016], Option [5] ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5.
PAGE 37
P 5.24 R O G R A M D E S C R I P T I O N S Loop Response The normal loop response time for all zones is 500 milliseconds. The panel will not consider a zone violated unless it is violated for at least 500 milliseconds. If Zone 1 is Fast Loop Response is enabled the loop response for zone 1 will be 40 milliseconds. Typically this can be used for vibration type sensors. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Zone 1 is Fast Loop Response .......................
PAGE 38
P R O G R A M D E S C R I P T I O N S Please refer to the LINKS1000 installation Manual for more information and connection diagrams. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ LINKS Preamble (First Telephone Number) ....................... Section LINKS Preamble (Second Telephone Number) .................. Section LINKS Preamble (Third Telephone Number) ...................... Section LINKS Preamble (All Telephone Number) ..........................
PAGE 39
P 5.29 R O G R A M D E S C R I P T I O N S On-Site Printer The panel, with the addition of the PC5400 printer module, will print all events as they occur to a local, onsite serial printer. All events printed will include the time, date, partition and the event. If a problem develops with the printer, such as power loss or paper outage the panel will store events until the problem is corrected, at which point it will print the events from the buffer.
PAGE 40
P 5.32 R O G R A M D E S C R I P T I O N S Installer Lockout If Installer Lockout is selected a hardware default cannot be performed. If a software default is performed all programming will restore to factory default. When Installer Lockout Disable is selected the panel will restore all programming to factory defaults if a hardware or software default is performed on the main control panel.
PAGE 41
Appendix A C O N T A C T I D Contact ID The Partition ID Codes must be 4 digits. All reporting codes must be 2 digits. The following is a list of Contact ID reporting codes. The first digit (in parentheses) will automatically be sent by the control. The last two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the alarm reporting code could be programmed as [34].
PAGE 42
Appendix B S I A V F O R M A T SIA Format Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - February 1993. This format will send the Account Code along with its data transmission.
PAGE 43
LIMITED WARRANTY Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
PAGE 44
© 1997 Digital Security Controls Ltd. 1645 Flint Road, Downsview, Ontario, Canada M3J 2J6 Tel. (416) 665-8460 • Fax (416) 665-7498 • Tech.
PAGE 45
Installation Manual PC5O1O WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Version 2.O DLS-1 version 6.
PAGE 46
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 47
Table of Contents PC5010 Control Panel Hookup Diagram ....................................... ii Section 1 - System Introduction 1.1 Specifications ....................................................................... 1 1.2 Additional Devices ............................................................... 2 1.2.1 Keypads ............................................................................... 2 1.2.2 PC5108 Eight Zone Expander Module ................................ 2 1.2.
PAGE 48
Hookup Diagram P C 5 0 1 0 C O N T R O L P A N E L ii