Specifications

P R O G R A M D E S C R I P T I O N S
27
If the SIA Sends Automatic Reporting Codes option is disabled the panel will operate as follows:
1.If the reporting code for an event is programmed as [00] or [FF] the panel will not attempt to call central station.
2.If the reporting code for an event is programmed as anything from [01] to [FE] the panel will send the
programmed reporting code.
3.Bypassed zones will never be identified, regardless of reporting code for “partial closing”.
Refer to Appendix B for a list of SIA identifiers.
Communicator Format ............................................ Section [360]
SIA Sends Automatic Reporting Codes ................ Section [381], Option [3]
Communicator Call Direction Options ................... Section [361] to [368]
SIA Identifiers ......................................................... Appendix B
5.6.4 Pager Format
The Communicator Format option for either phone number can be programmed for Pager Format. If an
event occurs and the Communicator Call Direction options direct the call to a phone number with the
Pager Format selected the panel will attempt to page.
When calling a pager extra digits will be required to make it work properly.
The following is a list of Hex digits and what function they perform:
Hex [B] - simulates the [
] key on a touch tone phone Hex [E] - two second pause
Hex [C] - simulates the [#] key on a touch tone phone Hex [F] - end of phone number marker
Hex [D] - forces the panel to search for dial tone
The panel will attempt to call the pager one time. After dialing the digits in the phone number the panel
will send the account number and reporting code followed by the [#] key (Hex [C]).
There is no ringback when using Pager Format. The panel has no way of confirming if the pager was
called successfully which means a failure to communicate trouble will never be generated.
The Pager Format cannot be used with the LINKS1000 cellular communicator.
Do not use the digit C in a reporting code when using Pager Format. In most cases, the digit C will be
interpreted as a [#], which will terminate the page before it has finished.
If the panel detects a busy signal, it will attempt to page again. It will make the maximum number of
attempts programmed in section [160].
Force dialing should be disabled when using Pager format.
When using Pager format, you must program two hex digit E’s at the end of the phone number.
Communicator Format Options .............................. Section [360]
Communicator Call Direction Options ................... Section [361] to [368]
5.7 Communicator - Reporting Codes
The panel can be programmed to report events to a central station. The panel will send the reporting
code programmed for the event.
5.7.1 Zone Alarm
The panel will transmit the Zone Alarm Reporting Code for a zone when the zone goes into alarm. 24
hour type zones will go into alarm whether the panel is armed or disarmed and report to the central
station. All other zone types will only go into alarm if the panel is armed.
Reporting codes can be one or two digits and can use HEX digits (A through F). The following is a description of
the different reporting codes that can be programmed and when the events will be reported to central station.
The Cross Zone Police Code Alarm will be sent when two different alarms occur during any armed-to-armed
period. When an alarm occurs while the panel is armed and a second alarm occurs on a different zone during the
same armed period, or after the system is disarmed, this code will be sent. All zone types contribute to this alarm.
The cross zone police code will be transmitted immediately unless either or both zones have the Transmission
Delay attribute enabled. If so, the code will be delayed for the programmed transmission delay time.
Cross Zone Police Code Alarm.............................. Section [328]
5.7.2 Zone Restoral
If the Restoral on Bell Timeout option is selected the panel will send the Zone Restoral Reporting Code
for the zone when the alarm output times out AND the zone is secure. If the zone is not secured when the
alarm output times out the panel will send the restoral immediately after the zone is secured.
If the Restoral on Bell Timeout option is not selected the panel will immediately send the Zone Restoral Reporting
Code when the zone is secured or when the panel is disarmed, regardless if the alarm output is active or not.
24 Hour type zones will report the restoral immediately after the zone is secured.
5.7.3 Closings
The panel will transmit a Closing Reporting Code to indicate a Partition(s) is armed. A different reporting
code can be transmitted for each User Code, Partition Master Code and System Master Code to identify
who armed the Partition(s).