INSTALLATION MANUAL PC1150 This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MADE IN CANADA Plug Type : RJ31X FCC Reg. No.: FSCAN-73151-AL-E REN = O.
NOTES FOR UL INSTALLATIONS This equipment is UL listed in accordance with UL 1023 (Household Burglar Alarm System Units). This equipment has not been investigated for compliance with UL 294, Access Control System Units. This equipment has the capability of being programmed for operational features that are not allowed for UL recognized installations. To stay within the standard for household applications, the installer should stay within the following guidelines when configuring the system. 1.
TABLE OF CONTENTS INTRODUCTION 3 Features ............................................................................................................................................... 3 Specifications ....................................................................................................................................... INSTALLATION 4 Mounting the Panel ..............................................................................................................................
PROGRAMMlNG SECTlONS [01] 1st Phone Number ..................................................................................................................... 14 [02] 1st Account Code ...................................................................................................................... 14 [03] 2nd Phone Number.. .................................................................................................................. 14 14 [04] 2nd Account Code ....................................
INTRODUCTION FEATURES SPECIFICATIONS Keypad Programmable The PC1 150 comes complete with a default program so that it is operational straight from the box with a minimum of programming. The control panel is completely programmable from the keypad.
INSTALLATION Mounting the Pane/ The keypad should be located close to the designated “Entry-Exit” door and be mounted at a height convenient for all users. Select a dry location close to an unswitched AC source and close to the telephone line connection. Remove the printed circuit board, the mounting hardware and the keypad from the cardboard packaging.
Burglary Zone Wiring Burglary zone definition, (for example, Delay, Instant, 24-Hour, and so on) is programmed using the keypad. Refer to Programming Guide Section [ll]. NOTE: For UL installations, zone inputs must be terminated with 1 kQ end-of-line resistors. 10lslsJ Burglary Zone Wiring Chart ~1 -1 I I END OF LINE RESISTOR 1kQ 0.
KEYPAD FUNCTIONS Introduction The PC1 150 keypad provides complete control of the PC1 150 control panel. The panel can be completely programmed from the keypad. The 4 zone lights provide alarm and status indication for the alarm circuits, and three function lights advise the user of system status. The built-in sounder lets the user hear correct key entries and other alert signals. The 12-digit keypad is used for code entry and other programming functions.
Arming Without Entry Delay To eliminate the Entry Delay, arm the system by entering [*][9][any Access Code]. An exit through a Delay Zone may be made as in normal arming. The system will arm as described in Auto-Bypass/ Home-Away arming whether an exit is made or not. The “Armed” light will FLASH to indicate that the system is armed and that there is no entry delay. If any zone is activated, an alarm will sound immediately. Disaming Enter the premises through the designated Entry-Exit door.
To display trouble conditions, enter [*][2]. Trouble conditions are represented with the following lights: Light Zone 1 Zone 2 Low Battery. lfthe batteryisdisconnected, itsvoltageis loworthe batteryfuseisopen, atrouble will be displayed and can be reported. AC Failure. On loss of AC power, the “System” light will come ON but the keypad buzzer will not sound. The keypad buzzer will sound if AC power remains off and the battery reaches a low voltage.
f*]+fsl: User Programming Command The [*][5] programming command allows the user to program Access Codes. The first Access Code is the Master Code and the installer may program the panel so that the user not able to change the Master Code; refer to Section [13]. The 6th code may be changed from a regular code to a One-Time Use code; refer to Section [13] Light 5. The One-Time Use code allows someone, such as maintenance personnel, to enter a code to disarm and then later re-arm the system.
Setting the Clock [*]+[G]i[Mas ter Code]+[ I] The System Clock uses a 24-hour clock format. For example, 8:05 AM would be entered as 0805; 1:30 PM would be entered as 1330. If the system is without power (both AC and battery), it cannot continue to keep time. When the panel is powered up, the system clock must be reset. If the time needs to be reset, the “Armed” light will come ON when [*][2] is entered to display trouble conditions.
Utility Output Command [*I+[71 or [*]+p]+[Access Code] The Programmable Output (PGM terminal) can be programmed to be activated by a keypad command. This output can be used to operate devices such as door strikes or special lighting. Depending on the option chosen, the [ $][7] commandmayormaynotrequireanAccessCodeto beentered. Whenthe[*][7]commandisentered,thesounder and the PGM output will be activated for 5 seconds.
PROGRAMMING GUIDE With the panel disarmed, enter [*][8][lnstaller’s Code]. The default installer’s Code is 1212. The Installer’s Code should be changed after the system is installed; refer to Section [20] Installer’s Code. Note that the panel can only be programmed while it is disarmed. When the Installer’s Programming Command is entered, the “System” light will FLASH to indicate that the panel is ready for programming.
Binary Data Display Zone lights 1 through 4 are used to display the value of each digit of data in a binary format as shown here: HEX data entry Refer to HEX Data Programming I I I Value Zone 1 Zone 2 Zone 3 Zone 4 I Zone Light ON 0 Zone Light OFF HEX Data Programming Some programming sections require that data be entered in a HEX (hexadecimal, or base 16) format. HEX numbering uses the digits 0 through 9 and the letters A through F.
PROGRAMMING SECTIONS [Of] 1st Phone Number This is the first telephone number the Communicator will dial; refer to Section [25] Communicator Call Direction. Enter the telephone number the same way it would be dialled it on a touch-tone phone. Press [#] after the last digit to complete the telephone number programming. A second dial tone search, as required in a PBX system, can be added by entering HEX ‘D’ between digits in the phone number. To enter HEX ‘D’, press [*] [4] [*I.
3/f format - Non-extencfed reporting Requires: l 3-digit account code in sections [02] or 1041. For example, enter 1230 for account code 123 l Format Code [0], [l], [2], [3], [4] depending on receiver type in section [23]. l Single line digit Alarm Reporting Code Section [05]. For example, enter [30] for single digit code 3 (0 = no pulses) TRANSMISSION SENT: 123 3 4/2 Format - Non-extended reporting Requires: l 4-digit account code in sections [02] or [04].
Opening [Disamingj Reporting Codes /After Alarm Reporting Code Opening Reporting Codes are transmitted to indicate disarming of the system by Access Codes 1 through 6. When the system is disarmed by one of the Access Codes, the corresponding reporting code in this section is transmitted. [OS] Refer to Section 1071 for examples of reporting code programming.
Zone Definitions Digit 2 Digit 2 determines the zone type as described below: PI Standard Delay: Entry and Exit Delays are normally used for Entry/Exit doors. The Exit Delay starts when the system is armed; the zone may be opened and closed during the delay without causing an alarm. When the Exit Delay expires, opening the zone will start the Entry Delay. During the Entry Delay, the keypad buzzer will sound steadily to indicate that the system should be disarmed.
[12] 1st System Option Code When Section [12] is entered, the 4 Zone Lights, “Ready” and “Armed” lights will indicate which options are enabled. If a light is ON, that option is enabled; if a light is OFF, that option is disabled. To enable or disable an option, press a number from [l] to [6]; [5] is used for the “Ready” light, and [6] is used for the “Armed” light. If the light indicating the option was OFF, it will come ON; if the light indicating the option was ON, it will go OFF.
1143 3rd System Option Code Refer to Section [12] for programming information.
El “Slow” Zone Response Time (01 to 99 x IO ms) Location [5] determines the “slow” zone response time; this time is programmable from 10 ms to 990 ms. The default Slow Zone Response Time is 500 ms. NOTE: The fast zone response time is fixed at 10 ms. 161 Test Transmission Cycle Time (01 to 99 days) Location [6] determines the frequency, in days, of the test transmission made through the communicator or by calling the downloading computer.
1231 Communication Formats This section determines the communication format to be used when transmitting information to the two telephone numbers programmed in Sections [Ol] and [03]. For each telephone number, enter one digit from the list below. Refer to “HEX Data Programming” for instructions on entering HEX numbers. The format for each phone number is determined by the type of receiver being called. Enter the format number for the 1st telephone number first.
Radionics Format For conventional Radionics 3/l format, the communications mode should be set on either Radionics rounds [B] or Radionics parity [Cl. The extended version of the Radionics format is normally used. Use the following guidelines to configure the PC1 150 for Radionics format: The customer account code must be only 3 digits with a zero making up the 4th digit. For example, enter 1230 to program the account code as 123.
PI Strobe Output (Latched Alarm Output) The PGM switches to ground on an alarm and remains low until the panel is disarmed. to indicate that an alarm has occurred before entering the premises. It can be used WI Failure to Communicate The PGM output switches to ground if the system fails to communicate after 8 attempts to each phone number that will be tried according to Section [25] Communicator Call Direction Options.
[30] Reset to Factory Default Software Reset Entering Section [30] will reset the control panel’s programming to the default settings. When Section [30] is entered, the keypad will beep several times and the “Trouble” light will come ON during the reset sequence.
1321 5th System Option Code Refer to Section [12] for programming instructions. LIGHT Loss of AC will not cause an AC trouble Loss of AC will cause AC troublem ON = No siren during Auto-Arm PI . OFF = 1 burst of siren every 10 seconds during Auto-arm pre-alert ON = Home-Away zones will have an entry delay when tripped [31 .
I PROGRAMMING WORKSHEETS NOTE: In sections [Ol] to [lo], do not enter data into sections that are not used. 1st Phone Number Page i4 Enter [0] for the digit 0 in the phone number. Enter [*4*] (HEX D) for additional dial tone detection between number digits, as in local PBX systems. Enter [#] to end the phone number entry ist Customer Account Code Page 14 Enter [*cl*] (HEX A) for the digit “0” in the account code. For a 3-digit code, enter [0] for the 4th digit.
Closing (Arming) Reporting Codes /Partial Closing Reporting Code I Page f5 Access Code 1 - Access Code 2 - Access Code 3 Access Code 4 I l---L-- Access Code 5 / Access Code 6 - Partial Closing Code Opening (Disarming) Reporting Codes / After Alarm Reporting Code Page 16 The “after alarm” code is sent on disarming if an alarm occurred during the previous armed period.
Page 16 Maintenance Alarms & Restorals Default For automatic test code reporting, time between reports (in days) must be specified in Section [17], and time of day for the report must be entered in Section [ 191. L!3JL_.-.lA Low Battery Alarm 3.AJu-l AC Fail Alarm ,F,8,, Fuse Failure Alarm ,E,3,- Low Battery Restore Azz.A_l- AC Fail Restore l.!z.d%- Fuse Failure Restore LEJ.J- Automatic Test Code Zone Definitions Page 16 NOTE: When defining zones, assign delay zones first to zones 1,2,3...
2nd System Option Code Page 18 Default Zone Light ON Zone Light OFF ,oFF, - Zone Light 1 Zone 4 N.O. without EOL Zone 4 normal ,oFF, - Zone Light 2 Master Code not changeable Master Code changeable ,oFF, - Zone Light 3 Siren Squawk enabled.
System Times Page 79 Default l.lL.!L- Entry Delay (seconds) t?!i_zJ- Exit Delay (seconds) ,0,4- Siren Cut-off (minutes) J.J_r&u/ AC fail transmission delay (minutes) &_QJ- Slow zone response time ( x 10 ms) &_!JJ- Test transmission cycle or auto download cycle time (days) Valid entries are “01” to “99”; do not enter “00”. Auxiliary Delay Zone Times Page 20 Default ,0,4,5, I Entry Time (seconds) &&QJ I Exit Time (seconds) Valid entries are “001” to “255”.
[23] Communication Formats Page 21 Default &L l--J 1st Telephone Number L.BJ I 2nd Telephone Number A format for both numbers must be programmed, even if the second telephone number is not used.
a Communicator Call Direction Options Page 23 This section must be completely programmed; do not press [#] to exit until all entries are completed. Default LL L-_ Zone Alarms and Restorals ,1, L.-l Access Code Openings and Closings J-l L-- Priority Alarms and Restorals L.
4th System Option Code Page 24 Default Zone Light ON Zone Light OFF Zone Light 1 Enable download answer Disable answer Zone Light 2 Enable download callback Disable callback Zone Light 3 Answering machine over-ride Disable over-ride Zone Light 4 “System” flashes on alarm when armed “System” light normal. “Ready” Light Quick-Arm enabled Quick-Arm disabled “Armed” Light Restore on siren time out Restore as follower ,ON, ,oFF, / I ,ON, I ,ON, - ,ON, L-_.
LIMITED WARRANTY Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot.
I FCC COMPLIANCE STATEMENT This equipment generates and uses radio frequency energy, and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
