PC4020 v3.3 (US, UL) • Installation Manual DLS-3 v1.3 WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
WARNING Please Read Carefully N o t e t o I n s t a l l e rs This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. Sy st e m F a il u res This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
Ta ble of Contents Section 1: Introduction 1.1 1.2 Section 2: Installation and Wiring 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 18 Partition Keypads .................................................................... 18 Global Keypads ....................................................................... 18 Keypad Toggle Options ......................................................... 18 Keypad Time-out ....................................................................
P C 40 2 0 Wi r i n g D i a g r a m ii
S ec tion 1: Intro d u cti o n 1.1 Out Of The Box Please verify that the following components are included in the PC4020 package. ❑ 1 PC4050C or PC4001C cabinet ❑ 1 Version 3.3 main control module ❑ 1 Hardware package which includes: ❑ 32 EOL resistors (5600Ω) ❑ 1 Black cabinet plug ❑ 1 Green ground strap ❑ PCB mounting standoffs ❑ 1 set of documents which includes: ❑ 1 Installation Manual ❑ 1 Programming Worksheets ❑ 1 Instruction Manual 1.
Section 2: Installation and Wi ring 2.1 Planning the System The speed and efficiency of installing a MAXSYS system will be greatly enhanced by planning the installation. As a minimum, the following checklist should be used to ensure that all of the details have been considered: ❑ Draw a diagram of the installation showing the location of the main panel, all keypads, zone inputs, bell outputs, relay outputs and annunciators. ❑ Indicate all partitions on the diagram.
I n s t a l l a t i o n W i r i n g Quantity Total (mA) Combus Current Selection Chart PGM1 (50/170mA max.*) Item PGM2 (50/170mA max.*) Combus (500mA max.)** Current (mA) x PC4850 135 x PC4936* 65 T-Link 150 Skyroute 30 Total Combus Current = Total (must not exceed 500mA) *PGM1/PGM2 (Standard Output) = 50mA max. NOTE: PGM1/PGM2 (Addressable Loop) = 170mA max. NOTE: To calculate Addressable Loop current, see 2.9 ‘AML Device Wiring‘. **See ‘Combus Current Calculation Chart’ below.
Capacitance Limits An increase in capacitance on the Combus will affect data transmission and will cause the system to slow down. Capacitance will increase for every foot of wire added to the Combus. The capacitance rating of the wire used will determine the maximum length of the Combus. For example, 22-gauge, non-shielded, 4-conductor wire has a typical capacitance rating of 20 picofarads per foot (which is 20nF/1000’).
I n s t a l l a t i o n NOTE: Only normally closed detection devices can be used with this type of zone supervision. Only one normally closed contact can be connected to each zone; multiple detection devices/ ontacts on one loop are not allowed, the tamper condition will not be monitored. W i r i n g LINKS Supervisory Zone This zone is for use with a LINKS1000/LINKS2150/ LINKS2450 only.
Addressable Devices The following addressable devices are available: • AMS-220/220T smoke detector with optional temperature sensor* • AMB-300 PIR detector • AMB-500 ceiling PIR detector • AMB-600 dual PIR detector • AMA-100 glass break detector • AMP-700 magnetic door/window contact • AMP-701 contact input module • AMP-702 fire alarm contact input module • AMX-400 repeater/isolator module • AML-770 isolator module *Fire alarm devices cannot be placed on the same loop as burglary devices.
I n s t a l l a t i o n a n d W i r i n g 2.11 Telephone Line Wiring The telephone terminals provide connections to the incoming telephone lines for central station reporting. The wires from the RJ-31X jack must be connected in the following manner: 2.13 Earth Ground Wiring NOTE: There must be no other telephone equipment connected between the control panel and the incoming telephone line (e.g. answering machines, fax machines, telephones, etc.).
The control panel monitors the presence of AC. Upon the loss of AC power a trouble condition will be generated. The keypad trouble light will turn on. If programmed, the keypad will also beep. For more information regarding AC options, see 10.1 ‘AC/DC Power Options‘. Applying Power to the Main Panel Once all field wiring has been completed and checked for opens, shorts and grounds, power can be applied to the panel as follows: 1. Connect the battery leads. 2. Connect the AC transformer.
Section 3: How to Program 3.1 Introduction to Programming The PC4020 is programmed via a menu system. Use the arrow keys (<>) to scroll through different menu options and press the [*] key to select the menu option displayed. Continue this procedure until the required program section is displayed, then press the [*] key to select it. To arrive at a program section where data can be entered may require scrolling and selecting items from several menus. Press the [#] to return to the previous menu.
3.4 Programming Hexadecimal Data Hexadecimal or ’Hex’ digits are often required for a programming item, such as telephone numbers and reporting codes. To insert a Hex digit into a given entry, press the [*] key to enter the Hex menu. Use the arrow keys to scroll through the each Hex digits (A through F). When the desired letter is displayed, press the [*] key.
Section 4: Module Enrollment 4.1 Enrolling Keypads and Modules Once the wiring of all keypads and modules is complete, they must be enrolled on the system. Apply power to the system by first connecting the battery, followed by the AC transformer. All LCD keypads will display the software version of the keypad. NOTE: Make sure all power to the system is OFF when connecting modules. NOTE: Record the location and number of each module for future reference.
4.3 Confirming Modules Ref # [0202] then scroll to desired module In case module numbers were not recorded, you can verify this information through the ’Confirm Module’ menu in the ’Module Hardware’ programming section in installer’s programming. This works just like enrolling modules. You will be prompted to ’Press Any Key On Desired Unit’ in the case of keypads and ’Create Tamper on Desired Unit’ in the case of modules. Once the correct action is taken, the keypad will display the module number (e.g.
Section 5: Partitions and Zones 5.1 Zone Supervision Ref # [000204] ’Zone Supervision’ The control panel must be instructed to supervise either No End of Line, Single EOL or Double EOL zone loops. These three options are described in Section 2.5 ’Zone Wiring’. To program this option, perform the following: 1. Enter installer’s programming by pressing [*] [8] [Installer’s Code]. 2. Enter reference number [000204] and press [*]. 3. Scroll through the three supervision types.
NOTE: When a partition is deleted, the zones assigned to it are removed from the Zone Assignment. Copying Partitions Ref #: [0102] Enter this section to copy the programming from one partition to another one. The programming that will be copied includes the Customer ID Code, Partition Toggles, Partition Times, Access Code Levels and Command Output Labels. The zone assignment will not be copied. To copy a partition: 1. The panel will prompt ’From Which Partition’.
P a r t i t i o n s Zone Types The following is a description of each zone type: Standard Delay (00) Standard Delay zones have an entry and exit delay. The exit delay will begin as soon as arming is initiated. The delay zone may be opened and closed during the delay time without causing an alarm. After the exit delay time has expired, the zone is armed. Opening the zone will start the entry delay. If the panel is disarmed before the entry time expires, no alarm will be generated.
• • • • • • • • • • the burglary outputs; if disarmed it will activate the keypad buzzer. When the partition is disarmed, this zone will not activate the verbal alarm feature on the PC4936. 24 Hr Buzzer (14): This zone, when violated, will activate the keypad buzzer. 24 Hr Technical (15): This zone is silent. 24 Hr Gas (16): This zone is audible. 24 Hr Heat (17): This zone is pulsed audible. 24 Hr Medical (18): This zone is silent. 24 Hr Emergency (19): This zone is audible.
P a r t i t i o n s Function Key Zone (33) The Function Key Zone definition, when selected, causes the panel to prompt the function key list and allow the installer to select the following list of functions: (00) Null Key (01) Stay Arm (02) Away Arm (03) No-entry Arm (04) Chime On/Off (05) System Test (06) Quick Exit (07) Arm Interior (08) Command O/P 1 (09) Command O/P 2 (10) Command O/P 3 (11) Command O/P 4 (12) Command O/P 5 (13) Command O/P 6 (14) Command O/P 7 (15) Command O/P 8 (16) Silence Trouble
Section 6: Keypad Operation 6.1 Partition Keypads A partition keypad is a keypad that can access one partition. You can assign a keypad to a partition when you enroll it (see 4.1 ‘Enrolling Keypads and Modules‘), or in the Partition Assignment section (see below). The partition keypad will primarily control the partition to which it is assigned. However, a user will also be able to control other partitions from the partition keypad, if that user’s access code allows it.
On each keypad, you can program each function key so that users will need to enter an access code before the panel performs the function. To do this, turn on the ’Funct. X Code’ toggle option for that key. The default setting is OFF for each key. NOTE: Some function key types will require an access code entry regardless of the programming in this section. See section 6.11 ‘Function Key Programming‘ for more information. 6.
lowed by the number of incorrect codes. Valid entries are from 000-255. The default setting is 005. The Lockout Duration is the length of time during which a keypad will be locked after the number of bad codes is reached. To program the lockout duration, enter reference number [00020201] followed by the lockout time. Valid entries are from 000 to 255 minutes. The default setting is 015. 6.8 Keypad Tampers Ref #: [000200] Enable this system toggle option if keypad tamper plates are being used. 6.
K e y p a d Quick Exit (11) Pressing this key will cause the panel to activate the Quick Exit feature. This feature must be enabled in order for the function key to operate (see Instruction Manual, Section 3.2 ’Quick Exit’). Arm Interior (12) This function key provides the user with a simple method for adding Stay/Away zones back into the system.
Section 7: Installer and Access Codes NOTE: Security codes should be changed from their default settings to ensure the security of the system. Do not program codes that can be easily guessed. 7.1 Installer’s Code Ref #: [000000] The installer’s code must be entered to access the installer’s programming mode. The default installer’s code is [5555] for the 4-digit option and [555500] for the 6digit option. Enter a new code using numbers from 0 to 9 only.
Program A New Code To program the new access code, perform the following: 1. From the Program Code menu, use the arrow keys to scroll to the first message: ’Select (0) Program Code’. Press [0] or [*] to program the access code. 2. The display will indicate ’Enter Digits’ followed by ’AAAA’. This is the default setting for the access code. Enter four or six digits for the new code. 3. The display returns to ’Select (0) Program Code’. The new code has been programmed.
[1] Dial tone search: This character will force the panel to search for a dial tone at that point in the telephone number. A ’D’ on the display represents a dial tone search. A dial tone search is already programmed as the first digit for each telephone number. [2] Pause 2 Seconds: This will add a 2-second pause to the dialing sequence, represented by the letter ’A’ on the display. [3] Pause 4 Seconds: This will add a 4-second pause to the dialing sequence, represented by the letter ’E’ on the display.
I n s t a l l e r Default Settings* GM 2M SM S System Master Select this option to program a System Master Code Yes Supervisor Select this option to program a Supervisor code. You must also program the partition mask for this code. Yes✦ Yes AC Arm Allows arming of the assigned partition(s). Yes Yes Yes Yes Yes Disarm Allows disarming of the assigned partition(s). Yes Yes Yes Yes Yes Bypass Allows bypassing of zones on the assigned partition(s).
7.8 Guard Code Ref #: [000004] The Guard code can only be changed in this section and cannot be altered by the user. The Guard code can always be used to silence alarms and arm all partitions. The code can only be used to disarm partitions the code is assigned to. In addition, the Guard code can also be used to bypass zones, activate command outputs and access the [*][6] System Master Options Menu when the code is active.
Section 8: Arming and Disarming 8.1 Arming and Disarming Options Ref #: [0100XX01] where XX = Partition 01-08 The following arming and disarming options are programmed by partition. If the Bell Squawk option is enabled, outputs will activate once briefly when the partition is armed and twice when the partition is disarmed. All outputs programmed for ’Fire and Burg,’ ’Inv Fire/Burg,’ ’Burg Only’ or ’Inv Burg Only’ will squawk (default=No). In an attempt to reduce false alarms, the Audible Exit Fault (Aud.
Section 9: Entry and Exit Delay Upon arming, the panel will begin the Exit Delay. If the ’Exit Delay Aud’ option is enabled, the keypad will beep every second until the exit delay expires (see 9.2 ‘Entry and Exit Delay Options‘). The keypad will beep rapidly for the last 10 seconds of the exit delay to warn the user that the system is about to arm. Upon entry, if a Delay type zone is violated, the panel will begin an Entry Delay. The keypad will emit a steady tone.
Section 10: System Programming 10.1 AC/DC Power Options Ref # [000200] The following options are used to determine the power settings for the system. Press [*] to toggle each option on or off. • Power Up Shunt: If enabled, all zones will be inactive during the first two minutes of power up to prevent causing false alarms (default=Yes). NOTE: Do not disable the Power Up Shunt option if AML devices are used. • AC Trouble Displayed: If enabled, the system keypads will display an AC trouble.
Clock Adjust Ref #: [00020308] This option is to compensate for any timebase inaccuracy. The panel will replace the last minute of each day with the number of seconds programmed in this section. For example, if the panel seems to lose nine seconds per day, program this section as [051]. Valid entries are 000-255 seconds. The default value is [060]. NOTE: Do not schedule events to occur during the clock adjust time. 10.
S y s t e m Ref #: [000401] Scroll to the TLM Enabled option. The panel will monitor the presence of the telephone line and will indicate a trouble condition if disconnected. If the TLM Enabled option is selected, the system will test for telephone line faults. The keypads will indicate any faults detected (default=Yes).
Waterflow Delay Ref #: [00020311] This delay is to prevent false alarms due to surges in the sprinkler system. The Maximum delay allowed is 90 seconds. The default is 000 seconds (disabled). The Waterflow Delay must be 90 seconds or less. This delay affects all zones programmed as Waterflow, zone type (10). See 5.4 ‘Zone Programming‘. 10.
Section 11: Programmable Outputs 11.1 Main Panel Outputs The main panel has four programmable outputs: Bell, SAUX+, PGM1 and PGM2. Adding PC4216/PC4204/ PC4204CX/PC4702 modules can expand the number of outputs. All outputs can be individually programmed to activate according to any of the programmable output options (listed in Section 11.2 ’Programmable Output Options’). SAUX+ Output Ref #: [0005] The SAUX+ output can supply up to 300 mA at 12VDC. It can be programmed as one of the output options (see 11.
closed. In order for the output to activate, the door chime feature must be enabled. TLM Only (13) The output will activate when a telephone line trouble is present. TLM and Alarm (14) The output will activate when a telephone line trouble is present and an alarm occurs on any of the selected partitions. Failure To Communicate (15) The output will activate when a Failure to Communicate trouble is present. The output will stay activated until a successful communication is sent to the central station.
P r o g r a m m a b l e HINT: If you program more than one PGM for the same command output (eg. command output 1), make sure that either: a) the PGMs are enabled for all the same partitions OR b) the partitions the PGMs are enabled for do not overlap. If the ’Inv Cmd Out #X’ system toggle option is enabled, the output will be inverted (i.e. the output will normally be energized, and will de-energize when activated). (Ref # [000200]) By default, this option is only enabled for Command Output #2.
Kissoff Pulse (00) Any output programmed for ’Kissoff’ can be active from 000 to 255 seconds. The default setting is 003 seconds. Ground Start (01) Any output programmed for ’Ground Start’ can be active from 000 to 255 seconds. The default setting is 000 seconds. NOTE: The panel will wait until the end of the Ground Start before dialing. This feature must not be used on UL listed systems. Chime Pulse (02) Any output programmed for ’Chime Pulse’ can be active from 000 to 255 seconds.
S e c t i o n 1 2 : C o m m u n i c a t i o n s P ro g r a m m i n g All options concerning communications can be programmed in the following sections, including telephone numbers, reporting codes, account numbers, communicator toggle options and miscellaneous communicator options. By default, the Comm Enabled toggle option is on to enable communications. To disable communications, enter reference number [000401]. ’Comm Enabled’ will appear on the display. Press [*] to toggle the option to [N]o.
disabled, the panel will send the restoral immediately when the zone is restored (default=No). NOTE: DO NOT enable this feature if the previous ’Restore on Bell Time Out’ option is enabled. NOTE: If Bell Shutdown is to be used, DO NOT enable this option. • Shut Down 24HRS: If enabled, the swinger shutdown counters will be reset every day at midnight, or when the partition is armed. These counters keep track of how many alarms have occurred on each zone, shutting them down if they reach their limit.
C o m m u n i c a t i o n s 12.5 Dialer Direction Ref #: [000400XX02] where XX = telephone number 00-02 The Dialer Direction programming section determines which reporting codes will be sent to which telephone number. Three groups of reporting codes can be selected: • alarms and restorals • openings and closings • all other miscellaneous codes These groups can be programmed to communicate to any or all telephone numbers. By default, all reporting codes are sent to the first telephone number only.
Contact ID Identifier Toggle Options • Partial Closing Identifier: This toggle option controls whether the Partial Closing reporting code will be transmitted with an identifier of 4 or 5 when using Contact ID. • Opening After Alarm Identifier: This toggle option controls whether the Opening After Alarm reporting code will be transmitted with an identifier of 4 or 5 when using Contact ID.
Section 13: Downloading NOTE: DLS-3 v1.3 or higher is required. Downloading is not to be enabled on UL Listed systems. 13.1 Downloading Options Automatic Upload of Event Buffer when %75 full Ref #: [000300] This option allows the installer to choose if the panel will automatically call the downloading computer when the Event Buffer %75 full event occurs.
Section 14: Event Scheduling Event scheduling allows for a variety of timed events to occur on specific dates and at specific times. Openings and closings can be suppressed during high traffic times, outputs may be programmed to follow date schedules and partitions may be auto-armed and auto-disarmed at specific times 14.1 Date Schedules Ref #: [001001] The panel uses date schedules to control the period during which an event will occur. There are 99 date schedules, each containing four intervals.
Open/Close Suppression Toggle If the Open/Close Suppression schedule is being used to suppress openings, toggle this option to [Y]. If it is to suppress closings, toggle this option to [N]. Date Schedule Enter the 2-digit number of the date schedule that will be used to suppress openings or closings.
Section 15: LINKS Communications 15.1 LINKS1000 (Cellular Communications) When using a LINKS1000 Cellular Communicator as a primary or backup means of communicating to the central station, the following sections must be programmed. For instructions on programming telephone numbers, please refer to Section 12.1 ’Telephone Numbers’.
Section 16: Diagnostics and Troubleshooting 16.1 General Diagnostics Ref #: [04] The diagnostics function is designed to help you track down any problems with the installed modules. If there is no problem the keypad will display ’PC40X0 System No Faults Found’. If there is a problem, the keypad will display ’Error... Module’. This message will be accompanied by either ’E’ ’T’ or ’LV’ followed by a number. The number represents the module (see list below).
occurs, the panel will not restore the trouble until it has been viewed using the [*][2] trouble display. The trouble will not be restored until it has been viewed, even if the cause of the trouble has been physically restored. If the option is turned off, the panel will restore these troubles as soon as the trouble condition is physically restored. The option is off by default. Trouble conditions can be transmitted to the central station, if programmed (see 12.7 ‘Reporting Codes‘).
Display Trouble Condition Alt. Comms AC Trouble The alternate communicator has lost AC power. Alt. Comms Battery TBL The battery connected to an alternate communicator module is low. Alt. Comms FTC Trouble The alarm control panel can no longer communicate with the central monitoring station. The trouble is generated after the programmed failed communication attempts. If a later attempt to communicate is successful, the trouble is cleared. Alt.
Appendix A: Reporting Codes Notes on Contact ID The following is a list of Contact ID reporting codes. The first digit (in parentheses) will automatically be sent by the control. The last two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the alarm reporting code could be programmed as [34]. The central station would receive the following: *BURG - ENTRY/EXIT - 1 In the above example, the ’1’ indicates the zone in alarm.
Dialer Direction* Contact ID SIA Auto Rep Codes** A/R (3) 73 ST-998/SJ-998 Ref. # Reporting Code Code Sent When... [00040309] Waterflow Trouble/Rest.
Dialer Direction* Contact ID SIA Auto Rep Codes** programmed number of days for delinquency has expired without partition being armed O (4) 54 CD-000 Walk Test Enabled walk test mode entered O (6) A7 TS-000 Walk Test Disabled walk test complete O (6) A7 TE-000 [00040316] General System Trouble/Rest. indicates one or more of following: PC4204/PC4204CX/PC4820/PC4702/PC4850***/ Alternate Communicator*** AC, battery and Aux Supply troubles/rest.
Appendix B: Zone Reporting Codes For notes on Contact ID and SIA reporting codes, see Appendix A. Zone Definition Contact ID Auto Rep Codes* Zone Alm/Rest. SIA Auto Rep Codes** Zone Zone Troub/Tam Fault/Rest. Alm/Rest. Zone Alm/Rest. Zone Troub/Tam Alm/Rest. Zone Fault/Rest.
Appendix C: ASCII Characters 52
Index A Access Code grand master 22 guard 26 options 26 second master 22 walk test 22 Access Levels 26 Account Number 13, 37 Addressable Loop current 6 enrolling devices 12 moving devices 12 panel key 12 removing devices 12 response time 6 wiring 6 AML.
UL Listed Commercial and Residential Installations The installation requirements listed below must be met for the following grades of service. Note: All modules, keypads and enclosures used with this control panel must be UL Listed/Labeled. Grade AA Central Station and Police Connect The installation must use T-Link module which communicates over LAN/WAN to the Sur-Gard MLR-IP receiver. Polling time must be 90 seconds. Compromise detection time must be 6 minutes.
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation.
Changes for PC4020 v3.3 The PC4020 v3.3 software incorporates several new features and changes. The most important additions are listed below: New Options & Features • Now has the ability to assign 128 addressable (AML) zones (See Section 2.9 “AML Device Wiring” on page 5). • T-Link (TCP-IP) module support (See Section 12.4 “Communicator Toggle Options” on page 37). • XSF card reader support (reader type 07). ©2002 Digital Security Controls Ltd. Toronto, Canada • www.dsc.
