Installation manual

ManualsBrandsDSC ManualsComputer equipmentPC580 - V2.3

If you are intending to use DLS-3 software with this product, a new DLS-3 driver must be

downloaded from the DSC web site at http://www.dscsec.com/dls3drivers.htm. Install

this driver on your computer in the same directory as your DLS-3 software.

W A R N I N G

This manual contains information on limitations regarding

product use and function and information on the limitations as

to liability of the manufacturer.

Section 1: IntroductionSection 1: Introduction

Section 1: Introduction

This manual describes how to install, program and maintain the PC5102-433. Before you

install the PC5102-433 module, you should complete the following steps in your system

installation:

1. Plan the installation and wiring of the security system (see your system

Installation Manual

2. Install the control panel, and install and enroll at least one keypad to use for programming.

Program the PC5102-433 from a system keypad or using DLS-3 v1.3 with the PC5102-433

v1.0 Driver Pack. Read your system

Installation Manual

for more information.

1.1 How to Use this Manual

Read this manual before you begin installing the PC5102-433. To install and set up the

PC5102-433 and wireless keys, follow these steps. Refer to the sections listed below.

1. Temporarily mount and wire the PC5102-433 module (see

Section 2

2. Enroll and program wireless keys (see

Section 3

3. Complete PGM and other programming on the system (see

Section 4

4. Test the placement of all the wireless keys

(see Section 5).

5. Permanently mount the PC5102-433 receiver

(see Section 5).

For additional information on trouble conditions and battery replacement, see

Section 6.

For help with troubleshooting, see

Section 7.

1.2 Specifications and Features

• Current Draw: 50mA (standby) 200mA maximum (both outputs active)

• Frequency: 433 MHz

• Receiver can receive signals from up to 8 wireless keys

• Antenna - internal. Installation not required

• Location

- can be wired up to 750 ft/230m. from the main panel with 22 gauge wire

- connects to Keybus

- for longer wire runs, thicker gauge wire must be used

• Compatibility: The PC5102-433 v1.X can be connected to the following panels:

PC501X, P832/DL, PC5020, P-8+, PC1555, P-6B, PC1555MX, P-6BMX, PC580, P-48

1.3 Compatible Wireless Keys

Please refer to the instruction sheets of the following keys for more information.

The PC5102-433 v1.X can receive signals from the following keys:

• WLS909-433 Wireless Key • WLS919-433 Wireless Key

• PWLS909-433 Wireless Key • PWLS919-433 Wireless Key

PC51O2-433NA v1.0 Installation Manual

Summary of content (12 pages)

PAGE 1
PC51O2-433NA v1.0 Installation Manual If you are intending to use DLS-3 software with this product, a new DLS-3 driver must be downloaded from the DSC web site at http://www.dscsec.com/dls3drivers.htm. Install this driver on your computer in the same directory as your DLS-3 software. Section 1: Introduction This manual describes how to install, program and maintain the PC5102-433. Before you install the PC5102-433 module, you should complete the following steps in your system installation: 1.
PAGE 2
1.4 Batteries The PWLS909-433/WLS909-433 use three A-76 batteries and the PWLS919-433/WLS919433 use two CR2032 lithium batteries. Section 2: PC5102-433 Set Up & Wiring This section describes how to set up and wire the PC5102-433 module. 2.1 Choose a Mounting Location for the PC5102-433 NOTE NOTE: Mount the PC5102-433 receiver and wireless keys after you have done placement tests with the wireless keys (see sections 5.1 and 5.2).
PAGE 3
2.5 Connecting a Garage Door to the PC5102-433 Connect an output of the PC5102-433 across the wall-mounted push button or directly at the motor of the garage door opener (please consult the garage door opener instructions for proper connections). Set up the system and wireless key so Garage door that it is programmed to pulse an output for a short pushbutton or motor duration (5 seconds) so that every time the programmed key is pressed the garage door is opened or closed.
PAGE 4
3.2 Enroll & Program Wireless Keys For wireless keys to work on the system, you need to enroll them and then program the function buttons, if the default values are not the functions desired. Wireless keys are not assigned to zones and require no zone programming. You can enroll up to 8 wireless keys on the system. Enroll Wireless keys 1. At a system keypad, enter [✱][8][Installer’s Code] to go to the installer’s programming section. 2. Enter programming section [804]. 3.
PAGE 5
Opening/Closing By Wireless Key Reporting NOTE NOTE: The Identified Wireless Key Closing option is only available with the PC5020, P8+, PC501X v2.0 and higher, P832/DL v2.0 and higher, PC1555(MX), P-6B(MX), PC580 v2.0 and higher, P-48 v2.0 and higher by turning section [015] option 4 off. To enable the reporting of openings and closings by identified wireless keys: • Make sure the control panel is v2.
PAGE 6
The system will generate a General System Supervisory trouble if the module is removed from the Keybus. If you need to remove the PC5102-433 module from an existing system, you will have to disable supervision of the PC5102-433. NOTE NOTE: Deleting all wireless keys from the PC5102-433 or defaulting the PC5102-433 will cause a supervisory fault. To disable PC5102-433 supervision: 1. Disconnect the PC5102-433 from the Keybus 2. Enter [✱][8][Installer ‘s Code]. 3. Enter [902].
PAGE 7
Testing Individual Wireless Keys To ensure that the PC5102-433 receiver is receiving transmissions from these devices, use the function keys on the (P)WLS909-433/(P)WLS919-433 at several different locations in the installation. 5.2 Mount the PC5102-433 When you have tested reception of the PC5102-433 with all the wireless devices (see section 5.1) and you have a good mounting location, mount the PC5102: 1. Pull the Keybus wires through the hole at the bottom of the back part of the cabinet. 2.
PAGE 8
Section 7: Troubleshooting 1. When I enter Sections [41] - [48] to add a wireless key, the keypad sounds a long beep. You cannot enter ESNs unless a PC5102-433 wireless receiver is connected to the Keybus. See section 2 for instructions on setting up and wiring the PC5102-433 module. 2. I have entered the ESN for the wireless key but when I press the function keys, the panel does not perform the desired function. Check the following: • Ensure the ESN has been entered correctly.
PAGE 9
P R O G R A M M I N G W O R K S H E E T Wireless Key Options En t r y 00 00 01-02 Key Des c r i p t i o n En t r y Key Des c r i p t i o n Null Key 17 17 [✱][1] Reactivate Stay/Aways For Future Use 18 18 For Future Use 03 03 Stay Arm 19 19 [✱][7][3] Command Output #3 04 04 Away Arm 20 20 For Future Use 21 21 [✱][7][4] Command Output #4 05 05 [✱][9] No-Entry Arm 06 06 [✱][4] Chime ON/OFF 07 07 [✱][6][ 22-26 ][4] System Test 27 27 For Future Use Disarm (OFF) F
PAGE 10
P R O G R A M M I N G W O R K S H E E T S Partition 8 Wireless Key Options [68] Function Key 1 03 l____l____l Function Key 3 27 l____l____l Function Key 2 04 l____l____l Function Key 4 30 l____l____l [91] Wireless Keys (1-8) Partition Assignments Default = 01 Wireless Key 01 l____l____l Wireless Key 02 l____l____l Wireless Key 03 Wireless Key 04 l____l____l l____l____l Wireless Key 05 l____l____l Wireless Key 06 l____l____l Wireless Key 07 l____l____l Wireless
PAGE 11
WARNING Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. System Failures This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
PAGE 12
LIMITED WARRANTY Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.